• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.3
• /
• pp.95-103
• /
• 2010

This paper presents a simulation model of a double-acting high-speed pneumatic cylinder with a relief valve type cushion mechanism. The model predicts piston motion, mass flow rate, pressure and temperature time histories of cushion chamber. Of interest here is to investigate the cushioning effect of varying the piston and piston-rod diameter, cushion ring diameter and length, and stoke in cushion mechanism. As a result, this cushion mechanism is found to be adequate under high-speed driving of pneumatic cylinders. The simulation model proposed here will be very useful to analyze the dynamic characteristics and to improve or design the better cushion mechanism in high-speed pneumatic cushion cylinders.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.1 no.1
• /
• pp.17-22
• /
• 2004

The goal of this paper is to improve the position control performance of pneumatic rotary actuator with variable brake using Magneto-Rheological Fluid. The air compressibility and the lack of damping of the pneumatic actuator bring the dynamic delay of the pressure response and cause the oscillatory motion. In this study, a variable rotary brake comprising Magneto-Rheological Fluid is equipped to the joint of a pneumatic manipulator. Experiments of step response have proved that the transient response of the manipulator could be improved compared with that of the conventional control algorithm by using a phase plane switching control algorithm.

• Journal of Drive and Control
• /
• v.9 no.2
• /
• pp.15-20
• /
• 2012

Pneumatic cylinder meter-out driving apparatus is used widely because it is clean, lightweight, and can be easily serviced. In this study an estimation method of energy consumption for pneumatic cylinder meter-out driving apparatus is proposed. The proposed method is derived from state equation and energy equation of air, and, the equation of motion of a moving part of a pneumatic cylinder reflecting the characteristics of the meter-out driving. The effectiveness of the proposed method is proved by simulation study and it demonstrates that the proposed method can evaluate the energy consumption quickly and easily when the parameters of the driving apparatus are changed.

• Journal of Ocean Engineering and Technology
• /
• v.18 no.4 s.59
• /
• pp.8-14
• /
• 2004

Pneumatic damping through an orifice-type duct for an OWC-type wave energy device is studied experimentally. Forced oscillation tests are used to measure chamber pressure and velocity of air-flow through an orifice. Pneumatic damping coefficients are deducted from the experimental research, and the influence of frequency, heave amplitude, and orifice size are discussed. Finally, two formulas are proposed for the estimation of non-dimensional pneumatic damping coefficient by regression analysis. The proposed formula proves to be a reliable method for practical application.

• Journal of Biosystems Engineering
• /
• v.35 no.1
• /
• pp.21-30
• /
• 2010

This study was performed to develop an active tire pressure control system that can adjust tire pressure to the optimum level according to traveling and working condition of agricultural tractor. For the development of active tire pressure control system, pneumatic supplier, solenoid valve block including pneumatic supply line, infinite rotation type pneumatic supplier with rotary joint unit, tire pressure transceiver module and control algorithm were developed. Also, tire simulator was developed. Using this tire simulator, the feasibility of each part constructing actual system was tested by checking the performance. The average communication success ratio was 98.3% between tire pressure transmitter and receiver module according to the various tire rotational speed and data receipt position of receiver module. The communication performance of the developed transmitter and receiver module was very stable in any condition. The tire pressure control system was accomplished by using the proportional control algorithm in this study. Also tire pressure control performance of developed control system was analyzed by using the tire simulator. As a result of control performance analysis to the developed system, the developed control system took 307 seconds to inflate agricultural tractor's tire from 50 kPa to 180 kPa. In opposite case, it took 210 seconds. Also it was able to control the tire pressure accurately under ${\pm}0.9%$ (FS) in any condition.

• Journal of Soil and Groundwater Environment
• /
• v.15 no.6
• /
• pp.53-63
• /
• 2010

Pneumatic fracturing is an emerging tool to enhance the remediation efficiency of contaminated unsaturated zones by injecting high pressure air and inducing artificial fracture networks. Pneumatic fracturing is reported to be well suited for the cases where the contaminated unsaturated zone thickness is less than 5 m as many contaminated domestic sites in Korea. Nevertheless, there have been almost no studies carried out on the site-specific efficiency and the optimized design of pneumatic fracturing considering the unsaturated zone characteristics of Korea. In this study, we employ numerical simulations to compare the efficiency of pneumatic fracturing on the aspect of the site remediation and the porosity improvement at several hypothetic unsaturated zones composed of four typical soil types. According to the simulation results, it is found that the zone with fine grains soil such as clay and silt shows better efficiency than the zone composed of coarse grains in terms of air flow and porosity enhancements. The results imply that pneumatic fracturing may improve the efficiency of site reclamation by jointly or independently applied to the many contaminated sites in Korea.

• Ocean Systems Engineering
• /
• v.2 no.2
• /
• pp.147-158
• /
• 2012

A time-domain simulation of a land-based Oscillating Water Column (OWC) with various irregular waves as a form of PM spectrum is performed by using a two-dimensional fully nonlinear numerical wave tank (NWT) based on the potential theory, mixed Eulerian-Lagrangian (MEL) approach, and boundary element method. The nonlinear free-surface condition inside the OWC chamber was specially devised to describe both the pneumatic effect of the time-varying pressure and the viscous energy loss due to water column motions. The quadratic models for pneumatic pressure and viscous loss are applied to the air and free surface inside the chamber, and their numerical results are compared with those with equivalent linear ones. Various wave spectra are applied to the OWC system to predict the efficiency of wave-energy take-off for various wave conditions. The cases of regular and irregular waves are also compared.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.488-491
• /
• 1997

In this paper, a ncw control 'ialvc which can misc air-iraksge pneumatically and compensate pressure drop for an alrho~ st system uas proposed A new control valve called "Pneuniatic C70ntro1 Valve (PCV)" functions as a control valve to compcns;ltc prcssure in thc casc of air-leakage. by using the pure pneummatic control ofpilot pressure. Based on the sirnulation of the proposed PCY, thc experimental system was fabricaied su as to illustrate the efficient pcrformance of the proposed PCV with anti-leakage. Such good perfo~manccs of PCV in the air-hoist system are shown by the simulation. In addition, the simulation bascd design approach presented in this paper can be applied to any hydraulic or pneumatic-hydraulic system.

• Proceedings of the KSR Conference
• /
• 1999.05a
• /
• pp.110-115
• /
• 1999

Experimental study is conducted to clarify the pneumatic characteristics of brake system for freight car. KNR(Korean National Railroad)'s freight cars have the laden-tare type control valve of brake system. But, laden-tare type control valve has some shortcomings to match the high speed freight car. Newly developed diaphragm type control valve is introduced to adopt freight car for speed-up. The test using the formated train set consisted of 21 cars is conducted to estimate the pneumatic braking efficiency of the mixed train set. From the results of experiment, the pressure characteristics of each brake cylinder show similar patterns qualitatively. But, in the case of release and brake application, quantitative pressure values of brake cylinder are different.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.5
• /
• pp.533-541
• /
• 2011

This paper presents a frequency-response test performed on an antagonistic actuation system consisting of two Mckibben pneumatic artificial muscles and a pneumatic circuit with pressure valves. Varying switching frequency to pressure valves from 0.1 Hz to 5 Hz, parameters of a linear model were estimated optimally to predict dynamic characteristics of the antagonistic actuation. A model-base control scheme with estimated parameters was built for the precise trajectory tracking of the antagonistic structure and realized on a reconfigurable embedded control system, CompactRIO. Experimental results showed that the proposed model-based control scheme gave good performance in trajectory tracking comparing with a PD control scheme when square wave and sinusoidal wave were given as references to follow.