• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.6
• /
• pp.1882-1892
• /
• 1996

This paper is concerned with the position control of the ond degree-of freedom manipulator using pneumatic artificial muscle actuator which is built to have a proper compliance. For t his pneumatic artificial muscle actuator though, it is difficult to make an effective control scheme due to the nonlinearity and uncertainties on the dynamics of the actuator. In this paper, a third-order equation of motion is derived for the actuator including the dynamics of the pneumatic servovalve. Later, various modeling uncertainties due to the nonlinearity and unmodeled dynamics of the servo vlave and the actuator are taken care of, as a trade-off between the closed-loop performance of the controlled system and its robustness to uncertainties. A controller using .mu. synthesis thchnique is designed, and robust performance against measurement noise, various modeling uncertainties due to the dynamics of the servo valve and actuator is achieved. The effectiveness of the proposed control methods is illustrated through simulations and experiments.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.12
• /
• pp.142-147
• /
• 1998

Developing robot hands with multi-degree-of-freedom is one of the topics that researchers have recently begun to improve the limitation by adding flexibility and dexterity. In this study, an articulated servo-pneumatic robot hand system with direct-drive joints has been developed whose main feature is the minimization of the dimension. The servo-pneumatic system is advantageous to fabricate a dexterous robot hand system due to the high torque-to-weight and torque-to-volume ratio. This enables the design of a finger joint with an integrated rotary vane type actuator which produces high output torque without reduction gears, being very robust. In order to control the servo-pneumatic finger joints, a miniature proportional valve that can be attached to the robot hand is required. In this paper, a flapper nozzle type 4/3-way proportional directional valve has been designed and tested. The experimental results show that the developed valve can control a finger joint satisfactorily without much vibratory joint movements and acoustic noises.

• Journal of Korean Institute of Industrial Engineers
• /
• v.21 no.4
• /
• pp.593-608
• /
• 1995

In this study two issues are considered, one is to develop a pneumatic servomechanism using a direct-connected circuit between inlet and outlet, the other is to design two kinds of advanced controllers such as fuzzy and PID controllers for a fingering system. Besides, the application of the advanced controllers to the newly proposed servomechanism is presented. The procedure of this study is composed of following 6 steps : [Step 1] Structuring of a control system; [Step 2] Development of a pneumatic circuit for the servomechanism ; [Step 3] Characteristic analysis of the valve and cylinder systems ; [Step 4] Determination of optimal parameters of the PID controller ; [Step 5] Design of a fuzzy controller and parameter tuning; and, [Step 6] Experimental analysis of fuzzy and PID controllers. Experimental results show that the newly proposed pneumatic servomechanism has good performance and, not only the performance of the fuzzy controller is better than that of the PID controller but also the fuzzy controller fits well to the control of the pneumatic servomechanism.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.3
• /
• pp.31-36
• /
• 2007

The excavator is complex machinery which has widely used in the construction site, deck of harbor and deep sea. The one of important issue of excavator system in recent is an automation of it in order to improve a working efficiency, a convenience working circumstance and work satisfaction. However, since there are large nonlinearities of control circuit, actuating cylinder, joiners of hydraulic units and changing loads etc., it is difficult to develope an automatic excavator system. Therefore, in this study, toy scale pneumatic excavator system is constructed and the remote control system is installed on it, before developing the automatic excavator system. In order to design the control system of the developed pneumatic excavator system, the transfer function is obtained using signal processing method and the controller gains of PID are decided based on CDM(coefficient diagram method). The obtained transfer function and the performance of the proposed control system is evaluated through experiments and computer simulation.

• Proceedings of the KSR Conference
• /
• 1999.05a
• /
• pp.110-115
• /
• 1999

Experimental study is conducted to clarify the pneumatic characteristics of brake system for freight car. KNR(Korean National Railroad)'s freight cars have the laden-tare type control valve of brake system. But, laden-tare type control valve has some shortcomings to match the high speed freight car. Newly developed diaphragm type control valve is introduced to adopt freight car for speed-up. The test using the formated train set consisted of 21 cars is conducted to estimate the pneumatic braking efficiency of the mixed train set. From the results of experiment, the pressure characteristics of each brake cylinder show similar patterns qualitatively. But, in the case of release and brake application, quantitative pressure values of brake cylinder are different.

• Journal of Engineering Education Research
• /
• v.19 no.2
• /
• pp.3-7
• /
• 2016

A flow control system was designed and fabricated to control the flow rate of liquid through the pipe. This control system was composed of hardwares and software, hardwares as controller, gate valve, orifice meter and data aquisition board and software as National instruments Labview program. Control of flow rate was executed by adjusting the pneumatic valve located at the center of pipe line based on the control signal generated by LabView PID control algorithm, which converts analog signal measured by pressure difference of orifice to digital signal to adjust pneumatic valve. For the controller setup Ziegler-Nichols tuning technique was applied and control performances were investigated for not only the disturbance but also the set point changes. Developed system showed good control performances in flow control enough to use as teaching tool of feedback control theory and practice in university, and also as industrial application.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.2
• /
• pp.30-37
• /
• 2012

Pneumatic Active Engine Mount(PAEM) with open-loop control system has been developed to reduce the transmission of the idle-shake vibration induced by engine effectively and economically. A solenoid valve installed between PAEM and vacuum tank is on-off switched by the Pulse Width Modulate(PWM) control signal to decrease the dynamic stiffness of the engine mount. This paper presents the methodology to identify the optimal values of control parameters of a PAEM, i.e, turn-on timing and duty ratio of PWM signal for 6 different idle driving conditions. A scanning algorithm was first applied to the vehicle test to obtain the approximate optimal control parameters minimizing the vibration at front seat rail and at steering wheel. Then the PAEM system identification was fulfilled to find accurate optimal control parameters by using multi-layer neural networks of Levenberg-Marquardt algorithm with vehicle test data.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.1407-1408
• /
• 2013

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.282-283
• /
• 2008

According to the development of vehicle technique, the improved NVH performance is required in the vehicle which have the high effectiveness and the high output of the powertrain. This vehicle has to be adapted to active engine mounting system to reduce the vibration in accordance with various vehicle information. The pneumatic active engine mounting system is consist with engine mount, solenoid valve, air tank and control unit totally. The important technique of this system is to reduce the vibration by the air pressure. This paper contains the development process of the pneumatic active engine mounting system and confirm the performance of this system test and vehicle test.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.4
• /
• pp.567-576
• /
• 2003

In this study, a robust controller to control pressure in a pneumatic pressure vessel with a long transmission line is proposed. Frequency response of transmission line using compressible fluid is changed by the flowing state of the fluid. So, it a fixed gain controller designed based on a model supposed the flowing state to a specific state, the performance of the control system could be degraded because of the modelling error. The controller designed in this study is composed of two parts. One is a feedback controller to improve a feedback characteristics and to compensate the influence of the variation of transfer characteristics of a transmission line owing to the change of flowing state and the other is a feedforward controller to regulate command fallowing performance. The experimental results with the designed controller show that the robustness of the control system is achieved regardless of the change of the model or the transmission line. Therefore, the designed controller can be utilized for the Performance improvement of a Pressure control system with a long transmission line using compressible fluid.