• 대한기계학회논문집B
• /
• 제25권3호
• /
• pp.322-329
• /
• 2001

A study of the shock wave turbulent boundary layer interaction is presented. The focus of the study is the interactions of the shock waves with the turbulent boundary layer on the falt plate. Three examples are investigated. The computations are performed, using mixed explicit-implicit generalized Galerkin finite element method. The linear equations at each time step are solved by a preconditioned GMRES algorithm. Numerical results indicate that the implicit scheme converges to the asymptotic steady state much faster than the explicit counterpart. The computed surface pressures and skin friction coefficients display good agreement with experimental data. The flowfield manifests a complex shock wave system and a pair of counter-rotating vortices.

• 센서학회지
• /
• 제28권5호
• /
• pp.318-322
• /
• 2019

In shooting training, an impact point identification system that uses the impact wave of the bullet to check the impact point in the target plate has been recently used. Acoustic sensors used in these systems must be able to detect shock waves of high sound pressure levels and be both waterproof and dustproof for rainy weather and dusty environments, respectively. In this study, membranes with excellent waterproof, dustproof, and sound transmitting characteristics were selected through a characteristics test; a protection cap was installed to install the selected materials. After coupling the produced protection cap to the acoustic sensor housing, the sensitivity and phase characteristics of the acoustic sensor were checked. Through the waterproof and dustproof test, the performances of its sensitivity and phase characteristics were confirmed. Finally, the normal shockwave of a 5.56 mm diameter bullet was measured using a shockwave detection signal collecting plate equipped with a prototype of the acoustic sensor at a 100 m firing range.

• 터널과지하공간
• /
• 제22권1호
• /
• pp.69-76
• /
• 2012

본 논문은 폭약의 폭발현상을 이용한 폭발용접, 폭발성형과 충격분말고화기술의 기본적 원리와 실험방법, 실험결과에 대하여 기술한다. 타이타늄(Ti)과 스테인레스 강(Stainless steel, SUS 304) 판재의 폭발용접 실험결과, 두 재료 접촉면의 단면에서는 연속적인 젯(jet)모양의 파형이 관찰되었고, 두 금속판재의 설치 경사각도가 $15{\sim}20^{\circ}$ 이고 접착속도가 2,100~2,800 m/s인 경우에 최적의 접합조건을 보였다. 알루미늄(Al) 판재를 이용한 폭발성형 실험과 전형적인 가압성형 실험 결과를 비교분석하여, 폭발성형의 경우가 큰 곡률변형을 보여 가공성이 우수한 것으로 확인되었다. 끝으로 금속과 세라믹의 혼합분말($Fe_{11.2}La_2O_3Co_{0.7}Si_{1.1}$)에 대한 충격고화 실험법을 제안하고 실험을 수행한 결과, 고화체의 표면과 내부에 균열이 확인되지 않았으며 세라믹입자와 금속입자들의 강한 미세조직 결합이 형성되었다. 또한 충격분말고화실험에서 발생되는 폭약의 폭발에 의한 폭굉파와 수중 충격파의 전파 및 간섭현상을 분석하기 위하여 LS-Dyna 3D를 이용한 동적해석을 수행하였다. 그 결과, 물용기 내 벽면에서 반사된 수중충격파가 중앙부에서 중첩되어 폭약의 폭발압력보다 높은 20 GPa의 수중 충격압을 보여, 물용기 내부형상의 중요성을 입증하였다.

• 한국소음진동공학회논문집
• /
• 제11권4호
• /
• pp.71-77
• /
• 2001

In this paper, stress wave propagation characteristics of MR(Magneto-rheological) inserts are experimentally investigated. Generally, stress waves of structures such as warships or submarines are induced by shock waves from underwater explosion. Their fatal effects on the shipboard equipments or structures damage the performance of warships. But, such a problem can be solved by controlling the stress waves propagating through structures by means of MR inserts. MR insert consists of two aluminum layers and MR fluid filled in between. Two piezoceramic disks are embedded on the host plate as a transmitter and a receiver of stress waves. Pulse waves are generated by the transmitter and they reach to the receiver through the MR insert. Permanent magnet and magnetic coil are used to produce magnetic field at the MR insert. In the presence of magnetic field, MR particles are arranged in chains parallel to the magnetic field such that the transmitted stress waves are reduced. Attenuation of stress waves is experimentally investigated.

• International Journal of Aeronautical and Space Sciences
• /
• 제17권3호
• /
• pp.324-331
• /
• 2016

The present study focuses on the characteristics of a supersonic jet flowing from a rectangular nozzle exit on a flat plate. Flow visualization techniques using schlieren and kerosene-lampblack tracing are utilized to investigate shock reflection structures and boundary-layer separations over a flat plate. Wall pressure measurements are also carried out to quantitatively analyze the flow structures. All observations are repeated for multiple jet flow boundary conditions by varying the flap length and nozzle pressure ratio. The experimental results show that the jet flow structures over the flat plate are highly three-dimensional with strong bleeding flows from the plate sides, and that they are sensitive to plate length and nozzle pressure ratio. A multi-component force measurement device is also utilized to observe the characteristics of the jet flow thrust vectoring over the plate. The maximum thrust deflection angle of the jet is about $8^{\circ}$, demonstrating the applicability of thrust vector control via a flat plate installed at the nozzle exit.

• 전산구조공학
• /
• 제8권1호
• /
• pp.137-146
• /
• 1995

본 논문에서는 최근 관심이 증대되고 있는 충격하중에 의해 시간의 흐름에 따라 형성되는 구조물의 응력분포 양상을 유한요소 해석적으로 고찰하기 위하여 동적 응력 해석 프로그램을 개발하였다. 유한요소 해석에 의하면, 종방향 응력파는 충격하중이 작용하는 방향과 동일한 방향으로 진행하며, 응력파 선단의 속도와 모양은 이론해석에 의한 결과와 같음을 알 수 있다. 또한 종파의 진행방향에 45.deg. 방향으로 전단파가 발생하여 진행함을 알 수 있으며, 전단파의 속도는 종파의 1/2이 되고, 종파보다 전단파의 강도가 큼을 알 수 있다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.795-801
• /
• 2004

An experimental study has been carried out to examine heat-transfer characteristics of an axisymmetric, under-expanded, sonic jet impinging on a flat plate and the local measurement of surface pressures and heat transfer coefficients on a plate have been achieved together with a visualization test of shock structure in a jet. As a result, it has been found that the Nusselt number distribution has different aspects depending on the under-expansion ratios and the nozzle-to-plate distances.

• 대한의용생체공학회:의공학회지
• /
• 제26권4호
• /
• pp.251-255
• /
• 2005

When the extracorporeal shock wave lithotriptor is operated, sounds can be heard. Then that might be a question about the location where the sounds come from. For the purpose of investigating the fact, we identify the location of the sounds radiated using one hydrophone. In order to carry out the experiment, it is needed to obtain direct waves from objects. Therefore, we present an experimental method to reduce reflected waves for obtaining direct waves only. The experimental results show the amplitude of waves can be attenuated about 28dB due to a silicon rubber plate of 8.5mm attached at the bottom. This is a quantified result that can expect to obtain the direct waves using the proposed method. Then, we carried out the experiment for the sound source location. From the experimental results, we can undoubtedly present a fact that the sounds are radiated from the objects to be shot due to shock waves.

• 한국항공우주학회지
• /
• 제34권12호
• /
• pp.18-24
• /
• 2006

슬롯과 다공판을 이용한 충격파와 난류 경계층 간섭유동의 피동제어에 관한 연구가 수행되었다. 슬롯의 다양한 형상 변화가 간섭유동에 미치는 영향이 관찰되었으며, 이를 위하여 간섭유동 후방에서 피토/벽압력 분포 및 쉴리렌, 유맥선, 오일막 간섭 줄무늬 형상과 같은 유동가시화 결과 등이 얻어졌다. 유동방향의 슬롯의 경우 간섭유동 후방에서 제어되지 않은 경우와 비교하여 보다 높은 피토압력이 국소적으로 관찰되었으나, 폭방향 슬롯제어는 전체적으로 제어되지 않은 경우에 비하여 피토압력 크기에서 큰 장점을 보이지 않았다.

• 한국전산유체공학회지
• /
• 제1권1호
• /
• pp.112-122
• /
• 1996

A finite element scheme using the concept of PISO method has been developed to solve the Navier-Stokes viscous flows in all speed range. This scheme includes development of new pressure equation that retains both the hyperbolic term related with the density variation and the elliptic term reflecting the incompressibility constraint. The present method is applied to the incompressible two-dimensional driven cavity flow problems(Re=100, 400 and 1,000). For compressible flows, the Carter plate problem(M=3 and Re=1,000) is computed. Finally, we have simulated the shock-boundary layer interaction(M=2 and Re=2.96×10/sup 5/), a more difficult problem, and compared its results with the experiment to demonstrate the shock capturing capability of the present solution algorithm.