• Korean Journal of Environmental Agriculture
• /
• v.8 no.2
• /
• pp.142-147
• /
• 1989

In this report, we set up a simple device which enabled us to obtain data useful to estimate the relative capacity of thermal energy retention of greenhouse built with various plastic coverings. A box($20cm{\times}20cm{\times}30cm$) framed with flexiglass at the edges and covered with thin plastic films was made, in which were placed a thermostat-controlled nichrom wire heater and a thermal probe made of thermister to monitor temperature changes. A wheaston-bridge type transducer and a chart recorder were used to record the changes of temperature inside the box The data obtained by using the device showed that the relative rate of heat toss through plastic films with identical thickness decreased in the order of PE film>EVA film>PVC film and that IR additives such as fine silica gel improved the insulating power of plastic films. This observations are in well accord with general information, demostrating the feasibility of the device in usefulness for the purpose of screening of various commercial plastic coverings.

• Proceedings of the KIEE Conference
• /
• 1999.07g
• /
• pp.3060-3063
• /
• 1999

We made a multi-layer conveyor sterilizing system using UV rays to prolong a storage period of dried marine products. The system is composed of 5 layer conveyor belt of 3 m long each, thus 15 m long in total. It is designed to radiate UV rays for 10 minutes the dried marine products, and can process 300 kg/hour. Eight UV lamps of 30 cm long and 15 W of power with 254 nm wave length are installed in parallel, 15 cm high above in each belt, and 40 lamps in total. The whole system is covered by 1 mm thick metal plates to block the UV rays except a front side which is covered with 5 mm thick plastic plates coated with UV protection film to survey inside of the system. A sterile ratio is about 99.97% with 10 minutes sterilization using this system.

• Applied Biological Chemistry
• /
• v.21 no.3
• /
• pp.144-149
• /
• 1978

Fermented soy sauce was dehydrated by spray drying to form powder, and moisture sorption properties of powdered soy sauce with or without cover of the flexible films were examined on different relative humidity by using saturated salt solutions at $30^{\circ}$. The results obtained were summarized as follows: The equilibrium moisture content of spray-dried soy sauce containing 18.3% moisture was determined to 52% by graphical interpolation method, and E.M.C. of powdered soy sauce covered with plastic films decreased at low relative humidity whereas sharply increased curves were seen at high relative humidity. The rate constant of moisture adsortion K for the power covered with films were $66.2{\times}10^{-5}\;to\;225{\times}10^{-5}/hr$., and K' became greater when film having higher water vapor transmission rate was used. The shelf-life of powdered soy sauce covered with Al. foil/P.E. film by Brown formula at the accelerated condition of $38^{\circ}$, 92% R. H. was the longest period, 164 days compared with any other films used, and the shortest period, 18 days in P.V.C. film.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.153-154
• /
• 2002

Wear map of silver coatings on AISI 52100 has been constructed to delineate the wear transition behavior with the change in operating conditions in various environments. Three main regimes were clearly identified: (i) elastic/plastic deformation of silver coating without failure. (ii) mild wear regime after initial failure of silver coating and (iii) severe wear regime. In the mild wear regime, the contact surfaces were covered with transfer layers of agglomerated wear particles. The transfer layer acted as a protective layer and resulted in low friction even after the initial failure of the coated films, whose characteristics were strongly dependent on both the operating and environmental conditions. Also, the existence of the critical sliding speed, above which no transfer layer was able to form, was discussed in the work.

• Journal of Biosystems Engineering
• /
• v.12 no.2
• /
• pp.16-27
• /
• 1987

Greenhouse farming was introduced to the Korean farmers in the middle of 1950's and its area has been increased annually. The plastic greenhouse, which is covered with polyethylene or polyvinyl chloride film, has been rapidly spread in greenhouse farming since 1970. The greenhouse farming greatly contributed to the increase of farm household income and the improvement of crop productivity per unit area. Since the greenhouse farming is generally practiced during winter, from November to March, the thermal environment in the plastic greenhouse should be controlled in order to maintain favorable condition for plant growing. Main factors that influence the thermal environment in the plastic greenhouse are solar radiation, convective and radiative heat transfer among the thermal component of the greenhouse, and the use of heat source. The objective of this study was to develop a simulation model for thermal environment of the plastic greenhouse in order to determine the characteristics of heat flow and effects of various ambient environmental conditions upon thermal environments within the plastic greenhouse. The results obtained are summarized as follows: 1. Simulation model for thermal environment of the plastic greenhouse was developed, resulting in a good agreement between the experimental and predicted data. 2. Solar radiation being absorbed in the plant and soil during the daytime was 75 percent of the total solar radiation and the remainder was absorbed in the plastic cover. 3. About 83 percent of the total heat loss was due to convective and radiative heat transfer through the plastic cover. Air ventilation heat loss was 5 to 6 percent of total heat loss during the daytime and 16 to 17 percent during the night. 4. The effectiveness of thermal curtain for the plastic greenhouse at night was significantly increased by the increase of the inside air temperature of the greenhouse due to the supplementary heat. 5. When the temperature difference between the inside and outside of the greenhouse was small, the variation of ambient wind velocity did not greatly affect on the inside air temperature. 6. The more solar radiation in the plastic greenhouse was, the higher the inside air temperature. Because of low heat storage capacity of the plant and soil inside the greenhouse and a relatively high convective heat loss through the plastic cover, the increase of solar radiation during the daytime could not reduce the supplymentary heat requirement for the greenhouse during the night.

• Journal of Bio-Environment Control
• /
• v.29 no.4
• /
• pp.428-439
• /
• 2020

This study was carried out to investigate the effect of PO film on the increase of crop yield and energy saving through PO and PE film greenhouse application and comparison test. As a experimental greenhouse, two single span greenhouses (1-1 W) and two double span greenhouses (1-2 W) were used. During winter season, PO film (0.15 mm outer layer, 0.10mm inner layer) was used as a covering material of greenhouse in double layers for double-span (B15) and single-span(B21), and PE film used for double-span (B15), and single-span (B23) as a control. The experimental vegetable was tomato(Solanum lycopersicum L.) cultivated in soil and the cultivar of that was 'Happiness'. That was cultivated from December 3, 2019 to April 30, 2020. The temperature at night inside the greenhouse was maintained at 15℃, and the side and roof windows were opened to maintain 23 ~ 24℃ during the day. As a result, this study showed that the yield in single-span greenhouse(B21) covered with a PO film increased 20% and that in double-span greenhouse (B16) increased by 9% compared to the greenhouse covered with a PE film (B23, B15). Fuel consumption of the single-span greenhouse (B21) with the cover of PO film was reduced by 12.4% and that of double-span greenhouse was done by 11.5% compared to that of the PE film greenhouse (B23, B15) without any difference between them in growing state.

• Archives of Plastic Surgery
• /
• v.37 no.3
• /
• pp.227-232
• /
• 2010

Purpose: Continuous irrigation method is an important step in managing wound infection. V.A.C. devices have been used in intractable wounds for reducing discharge, improving local blood flow, and promoting healthy granulation tissue. We expect synergistic effects of reduced infection and more satisfactory, accelerated wound healing when using both methods simultaneously. This study evaluated continuous irrigation combined with V.A.C. appliance for treatment of infected chronic wounds. Methods: We reviewed data from 17 patients with infected intractable chronic wounds. V.A.C. device (Group A) was used in 9 patients, and V.A.C. with antibiotics irrigation (Group B) was used in 8 patients. We placed Mepitel$^{(R)}$ on the surface of wound and placed an irrigation and aspiration tube on each side. A sponge was placed on the Mepitel$^{(R)}$ and covered with film dressing. The wound was irrigated continuously with mixed antibiotics solution at the speed of 200 cc/hr and aspirated through the wall suction at the pressure of -125 mmHg. V.A.C. applied time, wound culture and wound size were compared between the two groups. Results: No complication were seen in two groups. Compared with Group A, in the Group B, V.A.C. applied time was shortened from 32.7 days to 25.6 days and showed efficacy in the reduction rate of wound size. No statistical differences were shown in bacterial reversion. Conclusion: V.A.C. appliance with continuous irrigation is an effective new method of managing infected chronic wounds and useful to reduce treatment duration and decrease wound size. Moreover it could be applied more widely to infected wound.

• Journal of Bio-Environment Control
• /
• v.16 no.1
• /
• pp.72-77
• /
• 2007

This study was conducted to investigate the effect of functional cover film on oriental melon fruit quality under unheated plastic greenhouse cultivation in cold period. The 6 kind of films having different characteristics were covered at plastic greenhouses and oriental melon seedlings were cultivated at 2 regions of Seongju, respectively. The air-temperatures in plastic greenhouses of J-1 and J-2, having high infrared absorption rate, were about $2{\sim}5^{\circ}C$ higher than K-3. The contents of ${\beta}-carotene$ and sugar of fruit showed significant difference between functional and normal films. The sucrose, determining a sweetness during maturation, and soluble solids content of fruits cultivated in J-1, J-2, J-3, and K-1 were higher than those of K-2 and K-3. Ascorbic acid of fruits was highest in K-2 having low light transmission rate and thermo-keeping capacity. There was no significant difference in mineral content among all of cover films. These results indicated that the use of functional greenhouse covering films could improve fruit quality such as ${\beta}-carotene$ and sugar content of oriental melon.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.2
• /
• pp.26-33
• /
• 2009

A new testing method to evaluate the deposition potential of white pitch was developed. The new method involves depositing the potential white pitch particles on the air bubble covered plastic film in the pitch deposit tester (PDT) developed by KRICT and analysing the deposited area of white pitch using an image analyzer. In addition, the effect of two important factors (pH and calcium hardness) on white pitch deposition potential was elucidated. When pH of the coated broke stock was increased from neutral to alkali or the calcium hardness of the stock was decreased, the pitch deposit area was decreased, implying that these two factors have to be controlled during the evaluation of pitch deposition potential. It was found that hydrophobicity of the surface of latex binding films repulped is a key factor influencing white pitch deposition.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.3
• /
• pp.1-6
• /
• 2010

A new testing method named pitch deposit tester (PDT) was developed by KRICT in order to evaluate the deposit potential of micro-stickies. The new method involves depositing the potential pitch particles on the air bubble covered plastic film set in the pitch deposit tester (PDT) and analysing the deposited area by an image analyzer. In this study, the effect of fixing agents on potential pitch deposition was elucidated. The effects of some fixing agents (polyamine and polyethyleneimine) on pitch control were investigated by the PDT test of 100% recycled newsprint stock. The study suggested that proper use of the PEI can lead to better pitch control than that of polyamine. The efficiency of novel screening method using the PDT and retention and drainage analyser (RDA) for fixing agents in terms of retention and deposit contamination could be confirmed by above mentioned results.