• Advances in concrete construction
• /
• 제5권2호
• /
• pp.173-182
• /
• 2017

This paper is aimed at determining the shear and impact strength of waste plastic fibre reinforced concrete. M30 grade of concrete is prepared with waste plastic door fibres cut into 5 mm width and aspect ratios of 30, 50, 70, 90 and 110. Fibres are used in a volume fraction of 0 to 1.5% with an increment of 0.25%. L shaped specimens are cast for shear strength tests and flat plates of size $250{\times}250{\times}30mm$ are used for impact tests. "Drop ball method" is used for checking the impact strength. Shear strength is checked with L shaped specimens under UTM with a special attachment. It was found that up to 1.25% of waste plastic fibres can be effectively used for better strength of concrete both in shear and impact. Shear and impact strength were found to be increasing up to a volume fraction of fibres of 1.25%.

• Steel and Composite Structures
• /
• 제25권6호
• /
• pp.671-684
• /
• 2017

Elastic-plastic shear buckling behaviors of the web-post in a Castellated Steel Beam (CSB) with hexagonal web openings under vertical shear force were investigated further using Finite Element Model (FEM) based on a sub-model, which took the upper part of the web-post under horizontal shear force to represent the whole web-post under vertical shear force. A simplified design method for the web-post elastic-plastic shear buckling strength was proposed based on simulation results of the sub-model. Proper boundary conditions were applied to the sub-model to assure that its behaviors were identical to those of the whole web-post. The equation to calculate the thin plate elastic shear buckling strength was adopted as the basic form to build the design equation for elastic-plastic buckling strength of the sub-model. Parameters that might affect the elastic-plastic shear buckling strength of the whole web-post were studied. After obtaining the vertical shear buckling strength of a sub-model through FEM, the shear buckling coefficient k can be obtained through the back analysis. A practical calculation method for k was proposed through curving fitting the parameter study results. The elastic-plastic shear buckling strength of the web-post calculated using the proposed shear buckling coefficient k agreed well with that obtained from the FEM and test results. And it was more precise than those obtained from EC3 based on the strut model.

• Geomechanics and Engineering
• /
• 제8권1호
• /
• pp.53-66
• /
• 2015

Plastic wastes, particularly polyethylene terephthalate (PET) generated from used bottled water constitute a worldwide environmental issue. Reusing the PET waste for geotechnical applications not only reduces environmental burdens of handling the waste, but also improves inherent engineering properties of soil. This paper investigated factors affecting shear strength improvement of PET-mixed residual soil. Four variables were considered: (i) plastic content; (ii) plastic slenderness ratio; (iii) plastic size; and (iv) soil particle size. A series of unconfined compression tests were performed to determine the optimum configurations for promoting the shear strength improvement. The results showed that the optimum slenderness ratio and PET content for shear strength improvement were 1:3 and 1.5%, respectively. Large PET pieces (i.e., $1.0cm^2$) were favorable for fine-grained residual soil, while small PET pieces (i.e., $0.5cm^2$) were favorable for coarse-grained residual soil. Higher shear strength improvement was obtained for PET-mixed coarse-grained residual soil (148%) than fine-grained residual soils (117%). The orientation of plastic pieces in soil and frictional resistance developed between soil particles and PET surface are two important factors affecting the shear strength performance of PET-mixed soil.

• 한국지반환경공학회 논문집
• /
• 제14권1호
• /
• pp.33-42
• /
• 2013

In this paper, a series of monotonic undrained shear tests were carried out on four kinds of sand-fine mixtures with various fines content. Two kinds of sands (Silica sand V3, V6) and fines (Iwakuni natural clay, Tottori silt) were mixed together in various proportions, while paying attention to the void ratio expressed in terms of sand structure $(F_c{\leq}F_{cth})$. The undrained shear strength of mixtures below the threshold fines content was observed so that as the plastic fines content increases, maximum deviator stress ratio decrease for dense samples while an increase is noted for loose samples. For non-plastic fines, the increase in the amount of fines leads to an increase in density of the soil, which results in an increase in strength. Then, the monotonic shear strength of the mixtures was estimated using the concept of granular void ratio. It was found that the shear strength of mixtures is greatly dependent on the skeleton structure of sand particles.

• Geomechanics and Engineering
• /
• 제20권1호
• /
• pp.29-41
• /
• 2020

It is extremely important to obtain rock strength parameters for geological engineering. In this paper, the evolution of sandstone cohesion and internal friction angle with plastic shear strain was obtained by simulating the cyclic loading and unloading tests under different confining pressures using Particle Flow Code software. By which and combined with the micro-crack propagation process, the mesoscopic mechanism of parameter evolution was studied. The results show that with the increase of plastic shear strain, the sandstone cohesion decreases first and then tends to be stable, while the internal friction angle increases first, then decreases, and finally maintains unchanged. The evolution of sandstone shear strength parameters is closely related to the whole process of crack formation, propagation and coalescence. When the internal micro-cracks are less and distributed randomly and dispersedly, and the rock shear strength parameters (cohesion, internal friction angle) are considered to have not been fully mobilized. As the directional development of the internal micro-fractures as well as the gradual formation of macroscopic shear plane, the rock cohesion reduces continuously and the internal friction angle is in the rise stage. As the formation of the macroscopic shear plane, both the rock cohesion and internal friction angle continuously decrease to a certain residual level.

• Geomechanics and Engineering
• /
• 제20권6호
• /
• pp.497-503
• /
• 2020

In the Kingdom of Saudi Arabia, the shallower depth of the earth's crust is composed of loose dune or beach sand with soluble salts. The expansive behavior of salt bearing soil, fluctuation of ground water table and extreme environmental conditions offer a variety of geotechnical problems affecting safety and serviceability of the infrastructure built on it. Despite spending money, time and other resources on repair and rehabilitation, no significant attention is paid to explore the root causes of excessive differential settlement and cracking to these facilities. The scientific solution required to ensure safety and serviceability of the constructed infrastructure is to improve the strength and durability properties of the supporting ground. In this study, shredded plastic is employed as a low cost and locally available additive to improve strength characteristics of the desert sand. The study shows a remarkable increase in the shear strength and normal settlement of the soil. A seven (07) degree increase in angle of internal friction is achieved by adding 0.4 percent of the shredded plastic additive. The effect of different proportions and sizes of the plastic strips is also investigated to obtain optimum values. Such a long-lived solution will seek to reduce maintenance and repair costs of the infrastructure facilities laid on problematic soil along with reduction of environmental pollutants.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 봄 학술발표회 논문집
• /
• pp.397-402
• /
• 2003

This paper presents strut-and-tie models for predicting shear strength of RC interior beam-column joints considering the plastic hinge rotation of adjacent beams. On seismic design of frame system, it is controlled beams to occur plastic hinges and to be ductile so as to dissipate earthquake energy efficiently. The plastic hinge deformation of beams is used as analysis parameter in terms of strain of beam tensile bars at column face. The shear strengths of beam-column joints are evaluated by combining direct strut mechanism with truss mechanism. It is assumed that the max force transferred by direct strut mechanism is based on the strength of cracked concrete element, and that by truss mechanism is based on bond capacity.

• 대한치과교정학회지
• /
• 제28권5호
• /
• pp.681-688
• /
• 1998

본 연구는 브라켓 간접부착술식시 레진 베이스의 표면처리에 따른 전단결합강도와 파절양상을 비교함으로써 레진 베이스 표면처리의 효과를 평가해 보기 위하여 시행되었다. 소의 하악 중절치를 포매하여 만든 90개 시편의 석고 모형에 광중합형 레진 접착제를 이용하여 금속 브라켓을 위치시킨 후 대조군은 표면처리하지 않은 반면 실험군은 레진 베이스를 Plastic Conditioner와 sandblasting으로 각각 표면 처리하여 시편에 옮겨 부착한 다음 만능물성 시험기를 이용하여 전단결합강도를 측정하고,파절양상을 관찰하여 다음과 같은 결과를 얻었다. 1. 레진 베이스를 표면처리하지 않은 경우에 비하여 Plastic Conditioner와 sandblasting으로 각각 처리한 경우 평균 전단결합강도가 높게 나타났으며 통계적으로 유의한 차이를 보였다. 2. Plastic Conditioner로 처리한 군과 sandblasting으로 처리한 군 간의 전단결합강도는 통계적 유의차를 보이지 않았다. 3. 각 군의 파절양상을 접착제 잔류지수를 통하여 비교 관찰한 결과 세 군 간에 통계적 유의차를 보이지 않았다. 4. 전단결합강도와 접착제 잔류지수 간의 상관검정 결과 전단결합강도가 높은 경우 레진 베이스와 브라켓 경계부에서의 파절이 빈번한 경향을 보였으나 그 통계적 유의성은 보이지 않았다. 이상의 실험결과는 브라켓 간접부착술식에서 결합강도 증가를 위하여 레진 베이스의 표면처리가 필요함을 시사하였다.

• Geomechanics and Engineering
• /
• 제24권5호
• /
• pp.419-430
• /
• 2021

Investigation on the compressibility and shear strength of compacted loess is of great importance for the design and operation of engineering infrastructures in filling area. In this study, the mechanical behaviors of Yan'an compacted loess are investigated at various dry densities and water contents by conducting one dimensional compression and direct shear tests. And the elastic compressibility, plastic compressibility, yield stress and strength are obtained from the experiments. Results show that when water content increases, plastic compressibility parameter increases, but yield stress decreases. However, the increase of dry density leads to a decrease in plastic compressibility parameter but an increase in yield stress. In addition, elastic compressibility parameter is found to be a constant which is irrelevant to water content and dry density. As for strength, cohesion and internal friction angle is directly proportional to dry density, but inversely proportional to water content. Moreover, the mercury intrusion porosimetry (MIP) and scanning electron microscope (SEM) tests were also performed to observe the pore size distribution and microstructure of the specimens. Finally, by using results of MIP and SEM tests, the compressibility and strength behaviours of Yan'an compacted loess are explained from the perspective of pore-size distribution and microstructure.

• Advances in concrete construction
• /
• 제11권2호
• /
• pp.111-126
• /
• 2021

Concrete cracking due to brittle tension strength significantly prevents fully utilization of the materials for "flexural-shear failure" type shear walls. Theoretical and experimental studies applying fiber reinforced concrete (FRC) have achieved fruitful results in improving the seismic performance of "flexural-shear failure" reinforced concrete shear walls. To come to an understanding of an optimal design strategy and find common performance prediction method for design methodology in terms to FRC shear walls, seismic performance on shear walls with PVA and steel FRC at edge columns and plastic region are compared in this study. The seismic behavior including damage mode, lateral bearing capacity, deformation capacity, and energy dissipation capacity are analyzed on different fiber reinforcing strategies. The experimental comparison realized that the lateral strength and deformation capacity are significantly improved for the shear walls with PVA and steel FRC in the plastic region and PVA FRC in the edge columns; PVA FRC improves both in tensile crack prevention and shear tolerance while steel FRC shows enhancement mainly in shear resistance. Moreover, the tensile strength of the FRC are suggested to be considered, and the steel bars in the tension edge reaches the ultimate strength for the confinement of the FRC in the yield and maximum lateral bearing capacity prediction comparing with the model specified in provisions.