• Journal of Food Hygiene and Safety
• /
• v.34 no.1
• /
• pp.100-105
• /
• 2019

In this study, viable cells, coliforms and food poisoning bacteria were identified according to the pH levels of the coagulant and immersion liquid during each stage in the production of konjac, and storage stability was confirmed for 3 months. A considerable number of bacteria were found in the raw material, or powdered konjac (Amorphophallus konjac), as well as in the processing water. However, it has been shown that the plastic package were safe from microorganisms. Due to the high pH of the added coagulant [2.0% $Ca(OH)_2$], no contaminating bacteria were observed after konjac jelly formation. Coliforms were not detected any of the tested steps. During the molding process, the pH of konjac was adjusted to 9.5 ~ 12.5 at intervals of 0.5, and the number of bacteria was determined. As a result, no bacteria were detected in the alkaline range above pH 11.5. The pH of the immersion liquid was adjusted to 10.0 ~ 12.5, and after hardening, the konjac were stored at room temperature for 12 weeks. As a result, no bacteria, Escherichia coli or other food poisoning bacteria were detected at pH 11.5 or higher. Based on these results, it is expected that when the pH levels of the konjac and its immersion liquid are maintained at 11.5, it should be possible to keep the product for 3 months without additional sterilization process.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.4
• /
• pp.597-605
• /
• 2019

IPM bridge is an integral bridge that can be applied from span 30.0m up to 120.0m, the shape conditions of IPM bridge is also applicable to the rahmen bridge. In this study, to perform the structural analysis of Rahmen bridge and IPM Bridge, the researchers compared the distribution types such as load, moment, and displacement of those bridges. Structural analysis was carried out on four span models ranging from single span bridges to four spans of 120.0 m, based on span length of 30.0 m. Structural analysis was carried out on those bridge with span 30.0m up to 120.0m. The conclusions drawn from this study are as follows. 1) The bending moments were calculated to be large for the Rahmen bridge, and the horizontal displacements were estimated to be large for the IPM bridge. 2) Since the bending moments are derived by the span length rather than the extension of the bridge, the permissible bending moment for the span length should be considered in the design. 3) The pile bent of the IPM bridge did not exceed the plastic moment of the steel pipe pile at 120.0m span, but because the horizontal displacement in the shrinkage direction is close to 25mm, the design considerations are needed. 4) In the actual design, it is important to ensure stability against member forces, so review of the negative moment is most important.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.3
• /
• pp.443-450
• /
• 2021

After selecting a PES substrate with excellent thermal stability and optical properties among plastic substrates, a SiO₂ thin film was deposited as a buffer layer to a thickness of 20nm by plasma-enhanced chemical vapor deposition to compensate for the high moisture absorption. Then, the ITZO thin film was deposited by a RF magnetron sputtering method to investigate electrical and optical properties according to RF power. The ITZO thin film deposited at 50W showed the best electrical properties such as a resistivity of 8.02×10^-4 Ω-cm and a sheet resistance of 50.13Ω/sq.. The average transmittance of the ITZO thin film in the visible light region(400-800nm) was relatively high as 80% or more when the RF power was 40 and 50W. Figure of Merits (Φ_TC and FOM) showed the largest values of 23.90×10^-4 Ω^-1 and 5883 Ω^-1cm^-1, respectively, in the ITZO thin film deposited at 50W.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.12
• /
• pp.19-28
• /
• 2022

Cavities behind concrete walls can adversely affect the stability of structures. Thus study aims to detect cavities behind concrete structures using a microphone in a laboratory model test. A small-scale concrete wall is constructed in a chamber, which is composed of a reinforced concrete plate and dry soil. A plastic bowl is then placed between the plate and soil to simulate a cavity behind the concrete structure. Leaky surface acoustic waves are generated by impacting the concrete plate using a hammer and are measured using a microphone. The measured signals are analyzed using natural frequencies, and cavity-free sections are evaluated. The test results show that the first natural frequency decreases at the cavity section due to the flexural vibration behavior of the plate. In addition, the amplitude corresponding to the first natural frequency decreases as the measurement location becomes farther from the cavity center and significantly decreases at the measurement locations near the rebars. This study demonstrates that a microphone may be useful to detect cavities behind concrete walls.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.3
• /
• pp.92-102
• /
• 2022

Various numerical analysis models can be used to evaluate the behavior characteristics of tunnel facilities which are representative underground structures. In general, the Mohr-Coulomb model, which is most often used for numerical analysis, is an elastic-perfect plastic behavior model. And the deformation characteristics are the same during the load increase-load reduction phase. So there is a problem that the displacement may appear different from the field situation in the case of excavation analysis. In contrast, the HS-small strain stability model has a wide range of applications for each ground. And it is known that soil deformation characteristics can be analyzed according to field conditions by enabling input of initial elastic modulus and nonlinear curve parameter and so on. However, civil engineers are having difficulty using nonlinear models that can apply material nonlinear properties due to difficulties in estimating ground property coefficients. In this study, the necessity of rational model selection was reviewed by comparing the results of seismic performance evaluation using the Mohr-Coulomb model, which civil engineers generally apply for numerical analysis of tunnels, and the HS Small strain Stiffness model, which can consider ground nonlinearity.

• Explosives and Blasting
• /
• v.41 no.3
• /
• pp.38-61
• /
• 2023

An Excavation Damaged Zone(EDZ) caused by blasting impact changes rock properties, in situ stress distribution, etc., and its effects are noticeable at around a radioactive waste repository located at deep underground. In particular, the increase in permeability due to the formation of cracks may significantly increase the amount of groundwater inflow and the possibility of radioactive nuclide outflow. In this study, FLAC2D and FLAC3D were used to analyze the mechanical and thermal behaviors for three categories: a)No EDZ, b)Uniform EDZ, and c)Random EDZ. It was found that the tunnel displacement in the Random EDZ case was 423% higher than that in the No EDZ case and was 16% higher than that in the Uniform EDZ case. Tunnel inflow in the Random EDZ was also 17.3% and 10.8% higher than that in the No EDZ and the Uniform EDZ case, respectively. The permeability around the tunnel was increased by up to 10 times in the corner of the tunnel wall and roof due to the stress redistribution after excavation. From the computer simulation, it was found that the permeability around the tunnel wall was partially increased but the overall tunnel inflow was decreased with increase of stress ratio. Mechanical analysis using FLAC 3D showed similar results. Slight difference between 2D and 3D could be explained with the development of plastic zone during the advance of tunnel excavation in 3D.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.2
• /
• pp.141-149
• /
• 2018

In this study, compacting, passing performance, segregation resistance and rheological properties were tested to improve the stability of fresh concrete in the production and construction of self-compacting concrete (SCC) using hollow glass powder(GB). As a result, T50 reaching time was shortened up to amount of GB $2.0kg/m^3$. The compacting according to the amount of GB was improved by ball bearing effect of GB. However, T50 reaching time was slightly increased at $4.0kg/m^3$. In the case of passing performance, the result showed that plain was Class 1, GB $0.5{\sim}2.0kg/m^3$ was Class 0, GB $4.0kg/m^3$ was Class 1. Therefore, the passing performance was improved with 'No blocking' up to amount of GB $2.0kg/m^3$. Passing performance Block step (PJ) number by J-ring method was also best at GB $1.0kg/m^3$. In the case of segregation resistance according to the amount of GB, dynamic segregation resistance was increased compared to plain regardless of the amount of GB. And static segregation resistance showed 2.5% of segregation rate at GB $1.0kg/m^3$. Therefore, it was greatly improved compared to plain (12.5%). In the case of rheology property according to the amount of GB, plastic consistency by increasing of GB content didn't show big difference. However, yield stress by increasing of GB content was decreased with GB $1.0kg/m^3$. In conclusion, GB $1.0kg/m^3$ was effective for improvement of compacting, passing performance and yield stress. Also, it will be useful for stability of SCC by improving segregation.

• Journal of the Korean Wood Science and Technology
• /
• v.13 no.2
• /
• pp.14-34
• /
• 1985

One of the techniques for altering the properties of wood that has received considerable attention in the last twenty years is the formation of a wood-polymer composite (WPC) by irradiation and heat-catalyst polymerization of a monomer incorporated into the wood matrix. Wood-polymer composites are the new products having the superior mechanical and physical properties and the combinated characteristics of wood and plastic. The purpose of this experiment was to obtain the basic data for the improvement of wooden materials by manufacturing WPC and Staypak. The species examined was Hyunsasi-Namoo (Populus alba ${\times}$ P. glandulosa) which had not been utilized yet. Methylmethacrylate (MMA) as monomer, benzoyl peroxide (BPO) as initiator and methyl alcohol as bulking agent were used. The monomer containing BPO was impregnated into wood pieces by the dipping and the vacuum process for 2 hours. After impregnation, the treated samples were polymerized on the hot press with pressure and heat-catalyst methods. The results obtained were summarized as follows 1. The monomer loading into wood by the dipping process was 12.13 percent and 29.99 percent by the vacuum. The polymer loading into wood by the dipping process was 6.79 percent and 15.44 percent by the vacuum. 2. Comparing with Staypak, antishrink efficiency (ASE) of WPC was 12.5 to 13.6 percent on the radial direction and 14.70 to 18.63 percent on the tangential. Antiswelling efficiency (AE) was 14.40 to 17.22 percent on the radial direction and 17.18 to 42.1 8 to 42.14 percent on the tangential. Reduction in water absorptivity (RWA) was 8.19 to 15.5 percent. As a whole, the vacuum process was better than the dipping. 3. The specific gravity of control, Staypak and WPC were 0.44, 0.66 and 0.61 to 0.62, respectively. 4. In the bending strength test, the strength in case that the load direction is on the radial surface was greater than that which the load direction is on the tangential. 5. Increasing rate of stress at proportional limit in compression perpendicular to grain was 72.26 percent in case of WPC by the dipping process, 78.93 percent by the vacuum and 99.09 percent in case of Staypak.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.17 no.1
• /
• pp.24-32
• /
• 1984

In order to process instant foods which hold appropriate moisture contents and soft texture, four kinds of retort pouched seasoned-oyster products were prepared as control, seasoned products, solid smoked and liquid smoked product after seasoning and their processing conditions and quality stability during 100 days of storage were investigated. The optimum processing conditions of retort pouched seasoned-oyster product were as follows ; namely, raw oyster was seasoned at $105^{\circ}C$ for 10 min with seasoning solution prepared from sugar, sorbitol, salt, monosodium glutamate and 5'-ribonucleotide and then dipped for 30 seconds in Smoke-EZ solution(Alpha Foods Co., Ltd.) after predried for 30 min in hot-air drier. After. smoking, the seasoned and liquid smoked oyster was dried at $40-42^{\circ}C$ for 2.5 hours, vacuum packed in plastic film bag, and sterilized in a hot water circulating retort at $120^{\circ}C$ for 16 min. Comparing their quality before and after sterilization, TBA value of all the products after sterilization slightly decreased and among texture profiles hardness, toughness and chewiness slightly decreased, while elasticity and cohesiveness were rarely changed. Color value (a value) of the product treated with solid smoke or liquid smoke increased after sterilization. During storage pH, VBM and water activity of all products changed little and TBA values of the solid smoked product and liquid smoked one were lower than that of the others. Viable cell count was negative and texture changed little during storage. As for color difference during storage, green meat appeared on the surface of control and seasoned product after 15 days storage, while the masking of green meat could achieved by solid and liquid smoking treatment. And liquid smelling treatment was more effective than solid smoking. As a conclusion, retort pouched seasoned-oyster product treated with liquid smoke kept their good quality during 100 days storage and it seemed to be consumed as one of the instant foods which hold appropriate moisture contents and soft texture.

• Korean journal of applied entomology
• /
• v.56 no.3
• /
• pp.301-308
• /
• 2017

Locusts, Locusta migratoria (Orthoptera: Acrididae) are periodical unpredictable agricultural pests worldwide and cause serious damage to crop production; however, little consideration has been given to the management of this pest. Herein, we constructed a locust-pathogenic fungal library and confirmed that some fungi could be used as resources for locust management. First, the entomopathogenic fungi were collected from sampled soils using a Tenebrio molitor-based baiting system. For the locust assay, a locust colony was obtained from the National Institute of Agricultural Science and Technology. A total of 34 entomopathogenic fungal granules, which were produced by solid cultures, were placed in the plastic insect-rearing boxes (2 g/box) and nymphs of locust were contained in the box. In 3-7 days, mycosis was observed on the membranous cuticles of the head, abdomen, and legs of locusts. In particular, Metarhizium anisopliae, M. lepidiotae, and Clonostachys rogersoniana exhibited high virulence against the locust. Given that the 34 isolates could be used in field applications, their conidial production and stability (thermotolerance) were further characterized. In the thermotolerance assay, Paecilomyces and Purpureocillium isolates had higher thermotolerance than the other isolates. Most of the fungal isolates produced ca. >$1{\times}10^8conidia/g$ on millet grain medium. In a greenhouse trial, the granular application of M. anisopliae isolate on the soil surface resulted in 85.7% control efficacy. This work suggests that entomopathogenic fungi in a granular form can be effectively used to control the migratory locust.