• 반도체디스플레이기술학회지
• /
• 제9권2호
• /
• pp.111-116
• /
• 2010

In a large area magnetron sputtering system, which is under the influence of high heat load from the plasma, it is necessary to use the effective water cooling in order to maintain the proper deposition performance and the economic use of target materials. A series of three-dimensional numerical simulations are carried out on the simplified model of the large area magnetron sputtering system with the cooling plate that includes the U-shaped water channel. The analysis is focused on the effects of water channel geometry, cooling water flowrate, thermal conductivity of target material, and the degree of target erosion on the cooling performance of cooling plate, which is represented by the temperature distribution of target material.

• Bulletin of the Korean Chemical Society
• /
• 제31권2호
• /
• pp.397-400
• /
• 2010

Zirconium oxide thin films deposited on the p-type Si(100) substrates by radio-frequency (RF) reactive magnetron sputtering with different plasma gas ratios have been studied by using spectroscopic ellipsometry (SE), atomic force microscopy (AFM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The deposition of the films was monitored by the oxygen gas ratio which has been increased from 0 to 80%. We found that the thickness and roughness of the zirconium oxide thin films are relatively constant. The XRD revealed that the deposited thin films have polycrystalline phases, Zr(101) and monoclinic $ZrO_2$ ($\bar{1}31$). The XPS result showed that the oxidation states of zirconium suboxides were changed to zirconia form with increasing $O_2$ gas ratio.

• 한국재료학회지
• /
• 제26권8호
• /
• pp.438-443
• /
• 2016

We developed an Al sputtering process by varying the plasma power, process temperature, and film thickness. We observed an increase of hillock distribution and average diameter with increasing plasma power, process temperature, and film thickness. Since the roughness of a film increases with the increase of the distribution and average size of hillocks, the control of hillock formation is a key factor in the reduction of Al corrosion. We observed the lowest hillock formation at 30 W and $100^{\circ}C$. This growth characteristic of sputtered Al thin films will be useful for the reduction of Al corrosion in the future of the electronic packaging field.

• 한국세라믹학회지
• /
• 제31권7호
• /
• pp.731-738
• /
• 1994

TiN films were deposited on high speed steels by plasma assisted chemical vapor deposition (PACVD), cathode arc ion plating (CAIP) and reactive magnetron sputtering (RMS). The properties of the films deposited by the three different methods were compared. The preferred oriented plane of PACVD-TiN is (200) and those of CAIP-TiN and RMS-TiN are (111). PACVD-TiN shows a dome surface and a microstructure having small grains. CAIP-TiN shows the highest microhardness and the best adhesion strength of the three because it has a dense microstructure and an ill-defined interface. But is shows the greatest surface roughness due to the Ti droplet created by the arc. RMS-TiN shows a microstructure having large voids so that its properties in microhardness and adhesion are the worst of the three.

• 한국세라믹학회지
• /
• 제54권1호
• /
• pp.38-42
• /
• 2017

Vanadium nitride (VN) coatings were deposited using inductively coupled plasma (ICP) assisted sputtering at different ICP powers. Microstructural, crystallographic and mechanical characterizations were performed by FE-SEM, AFM, XRD and nanoindentation. The results show that ICP has significant effects on coating's microstructure, structural and mechanical properties of VN coatings. With an increase in ICP power, coating microstructure evolved from a porous columnar structure to a highly dense one. Single- phase cubic (FCC) VN coatings with different preferential orientations and residual stresses were obtained as a function of ICP power. Average crystal grain sizes of single phase cubic (FCC) VN coatings were decreased from 10.1 nm to 4.0 nm with an increase in ICP power. The maximum hardness of 28.2 GPa was obtained for the coatings deposited at ICP power of 200 W. The smoothest surface morphology with Ra roughness of 1.7 nm was obtained in the VN coating sputtered at ICP power of 200 W.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 추계학술대회 논문집
• /
• pp.357-360
• /
• 1996

MgO protection layer in ac PDP(plasma display panel) prevents the dielectric layer from ion bombarding in discharge plasma. The MgO layer also has the additional important role in lowering the firing voltage due to a large secondary electron emission coefficient. Until now, the MgO protection layer is mainly prepared by E-beam evaporation. In this study, MgO protection layer is prepared on dielectric layer of ac PDP cell by reactive R.F magnetron sputtering with Mg target under various conditions of oxygen partial pressure. Discharge characteristics of PDP is also studied as a parameter of MgO preparation conditions. The sputtered MgO shows the better discharge characteristics compared with MgO deposited by E-beam evaporator.

• ETRI Journal
• /
• 제31권6호
• /
• pp.703-708
• /
• 2009

Silicon antimony films are studied as resistors for uncooled microbolometers. We present the fabrication of silicon films and their alloy films using sputtering and plasma-enhanced chemical vapor deposition. The sputtered silicon antimony films show a low 1/f noise level compared to plasma-enhanced chemical vapor deposition (PECVD)-deposited amorphous silicon due to their very fine nanostructure. Material parameter K is controlled using the sputtering conditions to obtain a low 1/f noise. The calculation for specific detectivity assuming similar properties of silicon antimony and PECVD amorphous silicon shows that silicon antimony film demonstrates an outstanding value compared with PECVD Si film.

• 한국재료학회지
• /
• 제18권4호
• /
• pp.181-186
• /
• 2008

In this study, tantalum (Ta) compacts were fabricated in a spark plasma sintering (SPS) process and their microstructure and mechanical properties were investigated. Ta compacts with a density of 99% were successfully fabricated by controlling the sintering conditions of the current and the temperature. The density and hardness were increased as the sintering temperature increased. The $Ta_2C$ compound was observed at the surface of the compacts due to the contact between the Ta powder and graphite mold during the sintering process. The main fracture mode showed a mixed type with intergranular and transgranular modes having some roughness.

• 한국재료학회지
• /
• 제16권6호
• /
• pp.346-350
• /
• 2006

Al-doped ZnO (AZO) thin films were grown on type of glass#1737 substrates by DC magnetron sputtering. The structural, electrical and optical properties of the films were investigated as a function of various plasma discharge power. The obtained films were polycrystalline with a hexagonal wurtzite structure and preferentially oriented in the (002) crystallographic direction. The lowest resistivity was $6.0{\times}10^{-4}{\Omega}cm$ with the carrier concentration of $2.69{\times}10^{20}cm^{-3}$ and Hall mobility of 20.43 $cm^2/Vs$. The average transmittance in the visible range was above 90%.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.415-418
• /
• 1999

In this paper we studied that the effect of substrate temperature on crystallography and electrical properties of ZnO thin films. Facing Targets Sputtering system can deposit thin films in plasma-free situation and change the deposition condition in wide range. And prepared thin film\`s c-axis orientation and grain size were analyzed by XRD(x-ray diffractometer). In the results, we suggest that FTS system is very suitable to preparing high quality ZnO thin film with good c-axis orientation.