• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04a
• /
• pp.133-138
• /
• 2000

MgO thin films were deposited using $Mg(tmhd)_2$ as a precursor dissolved in a solvent by electrostatic spray pyrolysis. When a pure tetra hydro furan was used as a solvent, a large number of particles appeared on the MgO thin film surface due to homogeneous nucleation. However, by adding 1-butyl alcohol or 1-octyl alcohol to THF, homogeneous nucleation was restricted and the number density of the large particles was also drastically reduced. X-ray diffraction analysis showed that the MgO films had a (100) preferred orientation regardless of the type of solvents used. Characterization using Fourier Transformed-Infrared and spectroscopic photometer revealed that the crystallized MgO thin films on the glass substrate had a high optical transmittance (> 85 %) in the visible range. Discharge characteristics of MgO thin films deposited by ESP method on an alternating-current plasma display panel were compared with a MgO thin film prepared by reactive radio-frequency planar magnetron sputtering.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.6
• /
• pp.497-501
• /
• 2005

Dry film method was applied to fabricate lead-free transparent dielectric fur PDP(Plasma Display Panel). From various slurry compositions, it was able to find out the. best composition for producing high density green sheet. The slurry exhibited shear thinning characteristics which are known to be suitable fur producing a high quality green sheet. The thermal expansion coefficient of the fabricated transparent dielectric was measured to be $97{\times}10^{-7}/^{\circ}C$ which is close to the value of the glass substrate(PD-200). Cross sectional SEM of the transparent dielectric layer on PD-200 showed that the two layers were well attached each other with no observable gaps between them.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.196-196
• /
• 2003

현재 PDP(Plasma Display Panel) 상판의 유전체층은 저온에서 소성이 가능한 저융점 유리가 요구되기 때문에 융점을 낮추기에 용이한 PbO계가 주 성분으로 사용되어 오고 있으나. 최근 환경오염 등의 문제점으로 인해 Pb-free을 추구하는 새로운 유리조성의 연구가 많이 수행되고 있다. 이에 본 연구는 이미 PDP의 격벽과 봉착용 조성으로 많이 연구되어진 비스무스계 유리를 고려하여 PDP의 투명유전체용 조성을 찾고자 한다. Bi$_2$O$_3$-ZnO-SiO$_2$3원계를 기본으로 하는 유리조성에 유리망목형성제등을 첨가하여 열적특성과 광학적 특성을 조사하였다. 열적특성은 DTA를 이용하여 유리 전이 점(Tg) 및 융점(Tl)등을 측정하였고 TMA를 이용하여 선팽창계수(CTE)를 측정하였으며 유리섬유를 제조한 후 Littleton softening point (Ts)를 측정하였다. 광학적 특성은 페이스트를 제조하여 스크린프린팅 후 54$0^{\circ}C$~$600^{\circ}C$에서 1-2 h동안 소성하여 투광성을 조사하였다. 그 결과로, 열적특성으로는 400~5$50^{\circ}C$의 Tg, 450~$600^{\circ}C$의 Ts 및 5~11$\times$$10^{-6}$K의 CTE 값을 나타 내었고 광학적 특성으로 투광성은 양호한 특성(60% 이상)을 나타내었다. Bi$_2$O$_3$ 계를 현재 PDP의 투명유 전체에 적용시키기에는 유리용융시에 높은 점도와 환원 등의 문제점을 갖고 있지만 열적특성과 광학특성면에서는 가능성을 제시하여 향후 연구를 할 가치가 있다고 본다.

• Journal of Korean Institute of Industrial Engineers
• /
• v.41 no.1
• /
• pp.25-33
• /
• 2015

From the viewpoint of applications to manufacturing, data mining is a useful method to find the meaningful knowledge or information about states of processes. But the data from manufacturing processes usually have two characteristics which are multicollinearity and imbalance distribution of data. Two characteristics are main causes which make bias to classification rules and select wrong variables as important variables. In the paper, we propose a new data mining procedure to solve the problem. First, to determine candidate variables, we propose the multiple hypothesis test. Second, to make unbiased classification rules, we propose the decision tree learning method with different weights for each category of quality variable. The experimental result with a real PDP (Plasma display panel) manufacturing data shows that the proposed procedure can make better information than other data mining procedures.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.537-541
• /
• 2004

A high efficiency ZVS PWM asymmetrical half bridge converter for a plasma display panel (PDP) sustaining power module is proposed in this paper. To achieve the ZVS of power switches for the wide fond range, n small additional inductor $L_{lkg}$, which also acts as an output filter inductor, is serially inserted to the transformer primary side. Then, to solve the problem related to ringing in the secondary rectifier caused by $L_{lkg}$, the proposed circuit employs a structure without the output filter inductor, which helps the voltages across rectifier diodes to be clamped at the output voltage. Therefore, no dissipative RC (resistor capacitor) snubber for rectifier diodes is needed and n high efficiency as well as low noise output voltage can be realized. In addition, since it has no large output inductor filter, it features a simpler structure, lower cost, less mass, and lighter weight. Moreover, since all energy stored in $L_{lkg}$ is transferred to the output side, the circulating energy problem can be effectively solved. The operational principle, theoretical analysis, and design considerations are presented. To confirm the operation, validity, and features of the proposed circuit, experimental results from a 425W, 385Vdc/170Vdc prototype are presented.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.51 no.3
• /
• pp.132-136
• /
• 2002

In this study, we analyzed the luminous efficiencies of Ne-Xe-Ar and He-Ne-Xe-Ar mixing gas in compared with those of Ne-Xe and He-Ne-Xe mixing gas to improve luminous efficiency by adding a small amount of Ar gas. At the Xe 4%, the brightness of Ne-Xe and He-Ne-Xe mixing gas is higher than others. As the Xe % increases, power consumption decreases. Thus, in the Ne-Xe and He-Ne-Xe mixing gas of Xe 4%, we obtained maxium luminous efficiency. The Ar concentration is varied from 0.1% to 0.7% in this study. The luminous efficiency of the Ne-Xe(4%) mixing gas is improved to 1.16 and 1.13 lm/W by adding an Ar concentration of 0.4% and 0.5%, respectively. The luminous efficiency of the He-Ne-Xe(4%) (He : Ne = 7 : 3) mixing gas is considerably improved by adding an Ar concentration of above 0.3%. The maximum luminous efficiency of this mixing gas is 1.38 lm/W at the condition of adding an Ar concentration of 0.5%.

• Journal of the Korean Ceramic Society
• /
• v.45 no.2
• /
• pp.90-93
• /
• 2008

The oxygen gas behavior in PDP (plasma Display Panel) glass melts doped with sulfate ($SO_4^{-2}$) or blast furnace slag (BFS, $S^{2-}$) or both by means of yttria-stabilized zirconia (YSZ) electrodes was observed after the first fining. The temperature dependence of oxygen equilibrium pressure ($P_{O2}$) in each melt showed typical behavior, namely $P_{O2}$ decreased as temperature decreased. This suggests that an oxidation of $S^{4+}$ to $S^{6+}$ took place. However, the $P_{O2}$-value at constant temperature increased in the following order: BFS$P_{O2}$ of the melt doped with sulfate+BFS was much lower than that of the melt with only sulfate, although only 10% of sulfur was added by the BFS. This behavior can be explained by the redox reaction between sulfide ions in the BFS and dissolved oxygen ions in the melt during the first fining.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.41 no.5
• /
• pp.71-75
• /
• 2004

An efficient color compensation method is proposed to reduce the color difference between the camera based inspection system and the colorimeter based inspection system in a plasma display panel production line. The color compensation matrix can be constructed by using the relationship between RGB to XYZ conversion matrices, which are obtained by the RGB primaries and reference white chromaticity coordinates. Experimental results show that the non-contact color inspection system using the proposed color compensation method satisfactorily compensates the chromaticity coordinates acquired by the area color CCD camera to be matched to those measured by the colorimeter for various test color.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.2
• /
• pp.269-273
• /
• 2013

This paper analyzed a potential interference of electric equipments on radio service below 30MHz through an experiment with a PDP(Plasma Display Panel) TV and a RF(Radio Frequency) light bulb in an anechoic chamber. The radiation levels of the PDP TV and the RF light bulb are measured and a combined interference is calculated on the basis of the experimental value. As a result, the combined interference signal level is increased according to the number of interferer. The possibility of a potential interference from electric equipments on radio service below 30MHz is realized through comparison between the measured radiation value of electric equipments and the CISPR(International Special Committee on Radio Interference) 11 limit.

• Journal of the Korean Vacuum Society
• /
• v.12 no.S1
• /
• pp.88-91
• /
• 2003

Electromagnetic interference shielding and near-infrared cutoff filters for plasma display panel application were designed and fabricated by radio frequency magnetron sputtering. Three types of the filters were prepared: the basic structure of type A consisted of [$TiO_2$ Ti Ag $TiO_2$]; type B, of [$TiO_2$ ITO Ag $TiO_2$]; type C, of [$TiO_2$ ITO Ag ITO $TiO_2$]. Ti and ITO layers deposited on Ag layers were employed as barriers to prevent the oxidation and the diffusion of Ag film into the adjacent oxide layers. Optical, electrical, chemical, and structural properties were investigated, and the result shows that the filters with the ITO barrier layers provided an enhancement in transmittance in the visible owing to a lower absorption of ITO layers than Ti layers. Type C filter showed better optical and electrical performances and smoother surface roughness than Type B and C filters: the average sheet resistance was as low as 1.51 $\Omega\Box$ (where $\square$ stands for a square film), the peak transmittance in the visible was as high as 78.2 %, and the average surface roughness was 1.48 nm.