• 한국표면공학회지
• /
• 제30권2호
• /
• pp.111-120
• /
• 1997

The growth kinetion of $CuCl_x$ layer on Cu was investigated using $Cl_2$ gas with/without plasma. The etching kinetics ofit was also studied, in which PEt3 gas as well as $Cl_2$ gas were used. when plasma and DC bias were applied, not only the growth rate of $CuCl_x$ layer but also the surface concentration of Cl in $CuCl_x$ layer drastically increased. The growth mode is divided into three regimes, where the thinkness $CuCl_x$ layer ise proportional to t, lo9g $T^{1/2}$ , respectively, whether plasma, is applied or not. These three regime. It is also identified that the eath rate of Cu is drastically increased as the $Cl_2$ pressure is increased. However, when plasma and DC bias were applied, the etching rate is decreased, and ClCu-P-U layer is formed. in addition, as the etching time is increased, the surface concentration of Cl is increased and $CuCl_2$ formed partially.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.400-403
• /
• 2003

Etching characteristics of (Pb,Sr)$TiO_3$(PST) thin films were investigated using inductively coupled chlorine based plasma system as functions of gas mixing ratio, RF power and DC bias voltage. It was found that increasing of Ar content in gas mixture lead to sufficient increasing of etch rate and selectivity of PST to Pt. The maximum etch rate of PST film is $562\;{\AA}$/min and the selectivity of PST film to Pt is 0.8 at $Cl_2/(Cl_2+Ar)$ of 20 %. It was proposed that sputter etching is dominant etching mechanism while the contribution of chemical reaction is relatively low due to low volatility of etching products.

• 동굴
• /
• 제82호
• /
• pp.1-4
• /
• 2007

In this paper, the etching of Au films using photoresist masks on Si substrates was investigated using a capacitively coupled plasma etch reactor. The advantages of plasma etch techniques over current methods for Au metalization include the ability to simplify the metalization process flow with respect to resist lift-off schemes, and the ability to cleanly remove etched material without sidewall redeposition, as is seen in ion milling. The etch properties were measured for different gas mixing ratios of CF4/Ar, and chamber pressures while the other conditions were fixed. According to statistical design of experiment (DOE), etching process of Au films was characterized and also 20 samples were fabricated followed by measuring etch rate, selectivity and etch profile. There is a chemical reaction between CF4 and Au. Au- F is hard to remove from the surface because of its high melting point. The etching products can be sputtered by Ar ion bombardment.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.850-853
• /
• 1992

A cryogenic electron cyclotron resonance plasma etching system has been built to study wafer-temperature in the silicon etching characteristics. The wafer temperature was controlled from -150 to +30 $^{\circ}C$ during etching using the liquid nitrogen cooled helium gas. Although silicon was etched isotropically in $SF_6$ plasma at room temperatures, we found that it is possible to suppress the etch undercut in Si by reducing a substrate temperature without side wall passivation. In addition, the selectivity of silicon to photoresist was improved considerably at a low wafer temperature. Etch rates, anisotropy and selectivity to photo resist are measured as a function of the wafer temperature in the region of -125 $\sim$ 25$^{\circ}C$ and rf bias power of 20W $\sim$ 80W.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 춘계학술대회 논문집
• /
• pp.288-291
• /
• 1996

The surface properties after plasma etching of TiW solutions using the chemistries of BCl$_3$ and SF$\_$6/ gases with varying mixing ratio have been investigated using X-ray photoelectron spectroscopy. The elements of C, Cl, F, O and S are observed on the etched TiW films. After plasma etching with SF$\_$6/ gas, Ti-S bond are detected on the samples and Ti-S bond makes a role of passivation layer that surpresses Ti-O formation. After plasma etching wish BCl$_3$ gas, Ti are easily removed but W are hardly etched. As a results, W/Ti are increased on the etched sample.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 추계학술대회 논문집
• /
• pp.252-255
• /
• 1996

Cl-based gas chemistry is generally used to etching for Al alloy metallization. After the etching of Al alloy with Cl-based gas plasma, residual chlorine on Al alloy reacts with $H_2O$ due to air exposure and results in Al corrosion. In this study, the corrosion Phenomena of Al were examined with XPS(X-ray photoelectron spectroscopy) and SEF(Scanning electron microscopy). It was confirmed that chlorine mainly existed at the grain boundary of Al alloy after plasma etching of Al alloy with Cl-based gas chemistry and Al corrosion was largely generated at the grain boundary of Al a1loy. And residual chlorine was passivated by sulfur and fluorine which were generated by SF$_{6}$ plasma. These effects of passivation reduced the Al corrosion due to air exposure.e.

• 한국전기전자재료학회논문지
• /
• 제11권10호
• /
• pp.804-808
• /
• 1998

The inductively coupled plasma(ICP) etching of platinum with BCl$_3$/Cl$_2$ gas chemistry has been studied. X-ray photoelectron spectroscopy (XPS) was used to investigate the chemical binding states of the etched surface. The plasma characteristics was extracted from optical emission spectroscopy (OES) and a single Langmuir probe. In this case of Pt etching using BCl$_3$/Cl$_2$ gas chemistries, the result of OES and Langmuir probe showed the increase of Cl radicals and ion current densities in the plasmas with increasing Cl$_2$ gas ratio. At the same time, XPS results indicated that the intensities of Pt 4f decreased with increasing Cl$_2$ gas ratio. The decrease of Pt 4f intensities implies the increase of residue layer thickness on the etched Pt surface.

• 마이크로전자및패키징학회지
• /
• 제9권4호
• /
• pp.11-16
• /
• 2002

본 연구에서는 $SrBi_2Ta_2O_9$ (SBT)박막의 고속식각에 따른 잔류물질 및 식각 손상의 영향을 조사하였다. ICP-RIE (inductively coupled plasma reactive ion etching) 의 ICP power와 CCP(capacitively coupled plasma) power를 변화시키면서 고속식각에 따른 박막의 손상과 열화를 XPS 분석과 Capacitance-Voltage (C-V) 측정을 통하여 알아보았다. ICP와 CCP의 power가 증가함에 따라 식각율이 증가하였고 ICP power가 700 W, CCP power가 200 W 일때 식각율은 900$\AA$/min이었다. 강유전체의 건식식각에 있어서 문제점이 플라즈마에 의한 강유전체 박막의 열화인데 반응가스 $Ar/C1_2/CHF_3$를 20/14/2의 비율로 사용하고 ICP와 CCP power를 각각 700w와 200w로 사용하였을 때 전혀 열화되지 않는 강유전체 박막의 특성을 얻을 수 있었다. 본 연구 결과는 Metal-Ferroelectric-Semiconductor (MFS) 또는 Metal-Ferroelectric-Insulator-Semiconductor (MFIS) 구조를 가지는 단일 트랜지스터형 강유전체 메모리 소자를 만드는데 건식 식각이 응용될 수 있음을 보여준다

• 대한전자공학회논문지SD
• /
• 제39권1호
• /
• pp.31-38
• /
• 2002

0.35㎛-비아(via) 식각공정을 개선하기 위하여 C₂F/sub 6/가스의 식각특성을 분석하였다. 실험한 재료는 TEOS/SOG/TEOS 막을 올린 8인치 웨이퍼이며, 실험의 기법은 직교행열(Orthogonal array matrix) 실험 방식을 활용하였다. 산화막 식각에 이용된 장비는 transformer coupled plasma(TCP) source 방식이며 고밀도 플라즈마(HDP)장비이다. 실험의 결과는, 실험변수의 범위 내에서 C₂F/sub 6/는 0.8㎛/min-1.l㎛/min 범위의 식각속도를 보이며 균일도(Uniformity)는 ±6.9%미만으로 측정되었다. CD 변화(skew)는 식각 전과 후를 비교하여 10% 미만이었고 그 결과 비등방성(anisotropic) 식각의 특성이 우수하였다. C₂F/sub 6/를.20sccm 공급할 때 문제점이 발견되지 않았지만 14sccm을 공급하면 SOG 막의 내벽이 침식당하는 문제점이 있었다. 결과적으로 C₂F/sub 6/는 HDP TCP에서 빠른 식각비와 넓은 공정창(process window)을 가진 식각특성을 나타내었다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.1485-1488
• /
• 1997

The capacity of memory chip has increased vert quickly and 64MDRAM becomes main product in semiconductor manufacturing lines consists of many sequential processes, including etching process. although it needs direct sensing of wafer state for the accurae detching, it depends on indirect esnsing and sample test because of the complexity of the plasma etching. This equipment receives the inner light of etch chamber through the viewport and convets it to the voltage inetnsity. In this paper, EDP voltage signal has a new role to detect etching failure. First, we gathered data(EPD sigal, etching time and etchrate) and then analyzed the relationships between the signal variatin and the etch rate using two neural network modeling. These methods enable to predict whether ething state is good or not per wafer. For experiments, it is used High Density Inductive coupled Plasma(HDICP) ethcing equipment. Experiments and results proved to be abled to determine the etching state of wafer on-line and analyze the causes by modeling and EPD signal data.