• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.1
• /
• pp.153-163
• /
• 2000

The size effect on fracture toughness was investigated by introducing $J-A_2$ theory. For this application,small size specimens were chosen to establish $J-A_2$ assessment curve with FEM analysis. Two-dimensional FEM analysis was conducted with plane strain model using ABAQUS by domain integral method to calculate both crack tip stress and fracture toughness which were used to establish $J-A_2$ curve. The assessment curve predicted the fracture toughness of large specimens very well when compared to the test values. The results showed good prediction for deep crack specimen, though there were acceptable deviations in shallow cracked specimens, presumably caused by constraint effect. When the curve applied to reactor vessel in order to predict end of life fracture toughness with assumption of on-power pressure test condition, it provided the reasonable pressure compared to the existing design value. Better predictions would be possible if more test data were available.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.144-148
• /
• 2002

Influences of bending strain on the critical current (I$_{c}$) were investigated in Bi-2223 superconducting tapes at 77K. The effect of bending mode on the I$_{c}$ degradation behavior was discussed in viewpoints of test method, n-value and damage morphology. Especially, in this paper, we reported the I$_{c}$ behavior in Ag alloy/Bi-2223 multifilamentary super- conducting tapes under bending occurred within width x length plane of the tape which was called as a hard bending.nding.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.6
• /
• pp.207-213
• /
• 2001

Shaking table tests to investigate the dynamic friction behavior of interfaces between dense dry granular soils and construction material(concrete) were performed and the results are reported. The results show the variation of dynamic interface friction coefficients between dense dry granular soils and construction material was small in the sliding velocity range employed in this study. It was also observed that dynamic interface friction coefficients decreased as mean grain sizes of granular soils increased. These coefficients were compared with the friction coefficients obtained from the peak internal friction angles of the same granular soils by plane strain compression tests.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.119-122
• /
• 2004

Since a derailment of rolling stocks results in huge losses in properties and lives, the measurement of a derailment coefficient is a very important test item to estimate the running safety of rolling stocks. For a measurement of the derailment measurement of forces between the wheel and rail a measuring wheel-set should be made first. The process to make a measuring wheel-set has some stages for correct measurement. They are as follows; a finite element analysis of a wheel to find a position of holes at which vertical force shall be measured, a finite element analysis for the position of strain gauges.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.4 s.193
• /
• pp.123-130
• /
• 2007

Recently, a lot of work and interest have been devoted to the development of multiaxial fatigue parameters for fretting fatigue life prediction. In this study, the fretting fatigue lift and critical location ware estimated and evaluated through the multiaxial fatigue theories in a cylinder-on-flat contact configuration far Cr-Mo steel, SCM420, the material commonly is used in gears of the automobile and rollers of the conveyor. The strain-life curve was obtained from fatigue test for SCM420. The Fretting fatigue life and critical location were estimated through stress distributions, SWT-parameters and FS-parameters obtained from FEA. This paper showed possibility of applying multiaxial fatigue theories to fretting fatigue lift prediction comparing predicted life with experimental results.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.16 no.2
• /
• pp.47-57
• /
• 2020

A new elastic-plastic-creep constraint parameter is proposed to quantify the effect of constraint on creep crack initiation times. It represents the difference between the transient elastic-plastic-creep crack-tip opening stress and the Riedel-Rice opening stress field in plane strain, which can be determined analytically. Application of the proposed parameter to a large set of creep crack growth test data using C(T) and SEN(B) specimens of Type 316H stainless steel at 550℃ shows that creep crack initiation times can be more accurately characterized by the C⁎-integral together with the proposed parameter.

• Steel and Composite Structures
• /
• v.22 no.1
• /
• pp.141-159
• /
• 2016

Commonly in steel frames, steel beam and concrete slab are connected together by shear keys to work as a unit member which is called composite beam. When a composite beam is subjected to positive bending, flexural strength and stiffness of the beam can be increased due to "composite action". At the same time despite these advantages, composite action increases the strain at the beam bottom flange and it might affect beam plastic rotation capacity. This paper presents results of study on the rotation capacity of composite beam connected to Rectangular Hollow Section (RHS) column in the steel moment resisting frame buildings. Due to out-of-plane deformation of column flange, moment transfer efficiency of web connection is reduced and this results in reduction of beam plastic rotation capacity. In order to investigate the effects of width-to-thickness ratio (B/t) of RHS column on the rotation capacity of composite beam, cyclic loading tests were conducted on three full scale beam-to-column subassemblies. Detailed study on the different steel beam damages and concrete slab damages are presented. Experimental data showed the importance of this parameter of RHS column on the seismic behavior of composite beams. It is found that occurrence of severe concrete bearing crush at the face of RHS column of specimen with smaller width-to-thickness ratio resulted in considerable reduction on the rate of strain increase in the bottom flange. This behavior resulted in considerable improvement of rotation capacity of this specimen compared with composite and even bare steel beam connected to the RHS column with larger width-to-thickness ratio.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.1
• /
• pp.161-171
• /
• 1993

The aim of this study is to provide the stress-strain behavior of hardening geological materials such as rock or concrete on three dimensional spaces by using Desai model based on plastic theory. To validate proposed model, truly triaxial tests with high pressure under variety of stress paths in which three principal stresses were controlled independently using concrete materials were performed. The main results are summerized as follows: 1. Various stress paths for hardening materials used are satisfactorily explained by performing the truly triaxial test with high pressure. This is very important to investigate constitutive equations for materials like rock or concrete. 2. Since the proposed yield function is continuous, it avoids the singularity point at the intersection of two function in the previous models, thus, reducing the difficulties for computer implementation. 3. Analytic predictions for yielding behavior on $J_1-{\sqrt{J_{2D}}}$ octahedral and triaxial plane, as well as volumetric strain and stress-strain behavior agree well with experimental results.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.385-392
• /
• 2003

Traditional forms of river and coastal structures have become very expensive to build and maintain, because of the shortage of natural rock. Geotextile tubes hydraulically or mechanically filled with dredged materials have been applied in hydraulic and coastal engineering in recent years(shore protection structure, detached breakwater, groins and jetty). Recently, new preliminary design criteria supported by model and prototype tests, and some stability analysis calculations have been studied. In this study, the numerical analysis was performed to investigate the behavior of geotextile tube with various properties of geotextile and hydraulic pumping conditions. Numerical analysis was executed to compare with the results from the large-scale field model tests, and also compared the results of 2-D plane strain analysis and 3-D FEM analysis. A geotextile tube was modeled using the commercial finite element analysis program ABAQUS and the one-quarter of tube was modeled. Behavior of geotextile tube during the hydraulic pumping procedure was analyzed by comparing the large-scale field model test and numerical analysis. The shape variation and maximum tube height between the numerical analysis results and large-scale filed test results are turned out to be a good agreement.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.4
• /
• pp.160-166
• /
• 2006

Optical Fiber Bragg Grating sensor has a good performance to measure microscopic displacement which can measure strain of lining concrete and cylindrical structure like high intensity containment building and it can present many advantages like a corrosion resistance from the durability point of view. Then it can measure plane geometrical displacement of cylindrical structures with two-way displacement FBG sensor module. According to the test result, measurement of FBG sensor is better performance than other electric sensor system and 2D-level measurement. As a test result, Resolution of the two-way displacement sensor module with FBG sensors are more 10 times than other LVDT or 2D surveying.