• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.9A
• /
• pp.900-905
• /
• 2006

In this paper, PIFA antenna for $2.40{\sim}2.482GHz\;and\;5.75{\sim}5.85GHz$ is designed, fabricated, and measured. The prototype consist of hair-pin and short-pin. To obtain suitable bandwidth, the form layer is inserted between ground plane and substrate. Important parameters in the design are hair-pin length, width, position, air-gap height, and feed point position. From these parameters optimized, a PIFA antenna is fabricated and measured. The measured results of the antenna are obtained as follows results. The resonant frequency of the fabrication PIFA antenna is 2.37GHz and 5.86GHz bandwidth for approximately 90MHz with 350MHz(VSWR<2.0) and the gain is $1.91{\sim}4.37dBi$. H-plan and E-plan at 2.4GHz and 5.8GHz are shown as $52.83^{\circ},\;85.90^{\circ}\;and\;68.68^{\circ},\;52.143^{\circ}$ respectively.

• Journal of the Korean Vacuum Society
• /
• v.7 no.1
• /
• pp.24-28
• /
• 1998

Pd/Ge ohmic contact system on n-type InGaAs was studied. A good ohmic begavior by rapid thermal annealing was shown up to $400^{\circ}C$, and the specific contact resistance was reduced to low-$10^-6\Omega\textrm{cm}^2$EX>. However, above $425^{\circ}C$ it was deteriorated by intermixing and phase reaction of ohmic metals and InGaAs substrate. No remarkable phase change was observed below $350^{\circ}C$, but the reaction was initiated at ~$375^{\circ}C$ and considerable phase change was found above $425^{\circ}C$. Non-spiking and planar interfaces were observed even when annealed at $425^{\circ}C$, and smooth and shiny surface was kept up to $400^{\circ}C$.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.5
• /
• pp.611-620
• /
• 2011

A planar monopole antenna that was developed for WLAN/WiMAX application is presented in this paper. The proposed antenna with three strips, an asymmetrical ground plane, and a rectangular slit in the ground is designed to cover the popular frequency spectrum of WLAN (wireless local area network) bands and WiMAX (Worldwide Interoperability for Microwave Access) bands. The proposed antenna, which is capable of wideband operation, is fed by a strip line and fabricated on an FR-4 substrate. The obtained numerical results agree well with the experiment data. It was validated that the configuration can meet the demands for the WLAN/WiMAX systems and effectively enhanced the impedance bandwidth to 9.95% for the lower band and 76.05% for the upper band for VSWR < 1 : 2. This paper also presents and discusses the 2D radiation patterns and 3D gains according to the results of the experiment.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.368-371
• /
• 2020

In this paper, we propose a linear tapered slot rectifying antenna for a portable UHF-band RFID system. Since the proposed rectifying antenna does not use a dielectric substrate, the planar antenna is implemented with a thin metal thickness. The rectifier circuit converts input RF power into output DC voltage using a voltage doubler circuit based on two anti-parallel schottky diodes. The rectifying antenna is integrated by the voltage doubler circuit into a linear tapered slot antenna. For conjugate impedance matching of the rectifying circuit and the linear tapered slot antenna, the source-pull method was utilized by adjusting the angle of the tapered slot and the length of the antenna feed line. The proposed antenna prototype has been verified with the electrical and radiation characteristics through RF-DC conversion and far-field radiation test in open space measurement environment. Finally, the proposed antenna is realized to 0.23-wavelength (75 mm) and 0.18-wavelength (60 mm) at 915 MHz center frequency.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.9
• /
• pp.1642-1648
• /
• 2017

Ultra-wideband antennas are desired for several applications including satellite communications, radars, remote sensing system, telescopes, and microwave imaging systems. There are many types of wideband antenna structures, but the tapered slot Vivaldi antenna is advantageous in terms of cost, weight, scan angle capabilities, end-fire radiation, and ease of feeding and system integration. In this paper, a modified antipodal Vivaldi antenna is presented. A novel AVA with H-shaped parasitic patches has the capacity to improve the radiation characteristics in the whole operation frequencies. A prototype of the modified antenna with RT/duroid 5880 substrate of a relative dielectric constant (${\epsilon}_r$) of 2.2, and a thickness of 31mil is fabricated and experimentally studied as well. It measures a ${\mid}S_{11}{\mid}$ of less than -10dB and gain of 9-12dBi over 7.8-52.5GHz which shows reasonable agreement with the simulated one.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.71-72
• /
• 2013

In this paper, a design method for a compact slot antenna for 5.8 GHz RFID band (5.725-5.875 GHz) is studied. The proposed slot antenna is size-reduced by bending both ends of the straight slot in "${\Gamma}$"-shape, and a rectangular feed patch is located inside the slot. The effects of slot length, location of feed patch, and width and length of feed patch on the antenna performance are examined. A prototype antenna with optimized parameters for 5.8 GHz band is fabricated on an FR4 substrate and tested experimentally. The experimental results show that the frequency band for a VSWR < 3 ranges 5.72-6.13 GHz (bandwidth 410 MHz), and it corresponds fairly well with the simulated band 5.64-5.97 GHz (bandwidth 330 MHz). The fabricated antenna shows good radiation performance such as maximum power density in both directions normal to the slot plane, and low cross-polarization level of < -20 dB.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.5
• /
• pp.443-447
• /
• 2009

Bismuth-antimony-telluride based thermoelectric thin film materials were prepared by metal organic vapor phase deposition using trimethylbismuth, triethylantimony and diisopropyltelluride as metal organic sources. A planar type thermoelectric device has been fabricated using p-type $Bi_{0.4}Sb_{1.6}Te_3$ and n-type $Bi_{2}Te_{3}$ thin films. Firstly, the p-type thermoelectric element was patterned after growth of $5{\mu}m$ thickness of $Bi_{0.4}Sb_{1.6}Te_3$ layer. Again n-type $Bi_{2}Te_{3}$ film was grown onto the patterned p-type thermoelectric film and n-type strips are formed by using selective chemical etchant for $Bi_{2}Te_{3}$. The top electrical connector was formed by thermally deposited metal film. The generator consists of 20 pairs of p- and n-type legs. We demonstrate complex structures of different conduction types of thermoelectric element on same substrate by two separate runs of MOCVD with etch-stop layer and selective etchant for n-type thermoelectric material. Device performance was evaluated on a number of thermoelectric devices. To demonstrate power generation, one side of the device was heated by heating block and the voltage output was measured. The highest estimated power of 1.3 ${\mu}m$ is obtained at the temperature difference of 45 K.

• Corrosion Science and Technology
• /
• v.2 no.6
• /
• pp.289-295
• /
• 2003

The corrosion behavior of Cr-N coated steels with different phases (${\alpha}-Cr$, CrN and $Cr_2N$) deposited by cathodic arc deposition on Hl3 steel was investigated in 3.5% NaCl solution at ambient temperature. Potentiodynamic polarization test, electrochemical impedance spectroscopy (EIS) and scanning electron microscopy (SEM) were the techniques applied to characterize the corrosion behavior. It was found that the CrN coating had a lower current density from potentiodynamic polarization test than others. The porosity, corresponding to the ratio of the polarization resistance of the uncoated and the coated substrate, was higher in the $Cr_2N$ coating than in the other Cr-N coated steels. EIS measurements showed, for the most of Cr-N coated steels, that the Bode plot presented two time constants. Also, the $Cr_2N$ coating represents the characteristic of Warburg behavior after 72hr of immersion. The coating morphologies were examined in planar view and cross-section by SEM analyses and the results were compared with those of the electrochemical measurement. The CrN coating had a dense, columnar grain-sized microstructure with minor intergranular porosity. From the above results, the CrN coating provided a better corrosion protection than the other Cr-N coated steels.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.12
• /
• pp.1337-1342
• /
• 2012

In this paper, we propose a novel reconfigurable antenna that can change the electrical shape of the matching network using RF switches of PIN diodes. The designed antenna operates at two different modes that are Mode 1 (HSDPA band, 2.1~2.2 GHz) and Mode 2(WiBro WiFi band, 2.3~2.5 GHz). The antenna is built on both sides of a polyarcylate substrate. The measured reflection coefficient shows a matching bandwidth of 547 MHz($S_{11}$ <-3 dB, 2.035~2.582 GHz) for Mode 1 and 600 MHz($S_{11}$ <-3 dB, 2.2~2.8 GHz) for Mode 2, and it shows average vertical gains of -4.4 dBi and -4.5 dBi in x-y plane, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.3
• /
• pp.296-302
• /
• 2009

In this paper, a planar microstrip patch antenna is proposed using the slit on the top layer of a multi-layered structure for GPS application. The proposed antenna has a circular polarization at 1,575.42 MHz. This proposed antenna is fabricated on multi-layered FR4 substrate. The slits embedded on the top plane may yield to lower a resonance frequency and sustain a broad bandwidth. The proposed antenna size is $20{\times}20{\times}4.0\;mm^3$. The measured gain of 0.5 dBi, 10 dB bandwidth(VSWR 2:1) of 70 MHz(4.4 %), and 3 dB axial-ratio bandwidth of 15 MHz(1 %) have been obtained, respectively.