• 오토저널
• /
• 제5권1호
• /
• pp.45-53
• /
• 1983

There exist many kinds of frictions in internal combustion engine such as piston ring and skirt, cam and tappet, bearing friction etc. Among them, the frictions between piston ring, skirt and cylinder are particular. These frictions for motoring test are differ from that of firing test even though the temperature of cooling water and lubricating oil keep identically. The frictions for firing test are increased due to combustion pressure and products. The precise calculation of the friction is difficult. But we can assume that the friction is governed by the viscosity of lubricating oil and gas pressure of cylinder. And the viscosity of lubricating oil is dependant on gas temperature of cylinder, so the piston friction may be governed by gas pressure and temperature of cylinder. In this treatise, we propose the method of evaluating piston friction under the condition of constant engine speed, and we analyzed the behaviours and influence of factors concerned with the piston friction for output correction when the inlet pressure and temperature were varied. The main results are as follows: 1) The behaviours on the inlet conditions for the contact force of the piston rings and the viscosity of the lubricating oil concerned with piston friction are found. 2) The essential point the these behaviours is dependant on the cyclic variation following to the inlet conditions. 3) According to our analysis, It was observed that the viscosity of lubricating oil is more effective than the contact force to the piston rings.

• 한국가스학회지
• /
• 제12권4호
• /
• pp.58-62
• /
• 2008

본 연구에서는 직렬 6기통 압축천연가스 엔진의 피스톤에 대한 3차원 모델링을 수행하여 정상상태에서의 온도분포 및 그에 따른 열응력과 변형을 예측하고, 이를 기존의 해석결과와 비교 검토를 통하여 피스톤의 유한요소해석의 기준을 구축하고자 한다. 또한 냉각시스템의 성능이 피스톤의 열부하에 미치는 영향을 평가하기 위하여 냉각수 온도의 변화에 따른 피스톤의 온도분포 및 열응력 분포 그리고 그에 따른 변형을 분석하였다. 분석결과 피스톤의 최고 온도는 크라운부의 중앙에서 나타났고, 피스톤의 크라운 하부에서 최대 열응력이 발생하였다.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2005년도 연구개발 발표회 논문집
• /
• pp.448-453
• /
• 2005

Temperature Control Valve (TCV) is one of the useful temperature control devices, which is used to control constant temperature of working fluid in power and chemical plants and domestic water supply systems. TCV is composed of body, cylinder and piston, and the body shape has a symmetrical H-type. In general, it has several inlet and outlet holes, and its shape is like as tubular sleeve. The piston has three rings two rings of the end of piston have the function of controlling inlet flow rate with hot and cold working fluids, the center ring has the function of preventing hot and cold water from intermixing. Consequently, the shapes of piston and cylinder are the main design parameters in the performance of TCV. In this study, numerical analyses were carried out with two different piston and cylinder shapes to investigate the functions as a temperature control valve and the flow characteristics according to piston opening grade in TCV. Using a commercial code, FLUENT, velocity and pressure fields in TCV are obtained under steady, standard $k -{\epsilon}$ turbulence model and no-slip condition.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권3호
• /
• pp.538-550
• /
• 2004

The convection heat transfer coefficients on the top surface of a large liquid petroleum liquid injection(LPLi) engine piston with the oil gallery are analyzed by solving an inverse thermal conduction problem. The heat transfer coefficients are numerically found so that the difference between analyzed temperatures from the finite element method and measured temperatures is minimized. Using the resulting heat transfer coefficients as the boundary condition, temperature of a large LPLi engine piston is analyzed. With varying cooling water temperature, temperature, stress, and thermal expansion of the piston are analyzed and evaluated.

• 오토저널
• /
• 제9권3호
• /
• pp.55-65
• /
• 1987

This paper presents the method of piston temperature measurement and its data under various engine operating conditions. In case of high speed engine, the thermocouple wires must be guided from moving piston to stationary place with carful attention. for this purpose L_LINK SYSTEM was made and assembled to a passenger car engine on the test bench and then the piston temperature was successfully measured. The tested engine speed ranged from 1,000 to 4,000 rpm with 500 rpm increments. Not only the effects of engine speed and load on the piston temperature but those of spark timing, detonation, coolant temperature and Reynolds number based on inlet air condition were studied form the measurement obtained by this L_LINK SYSTEM.

• 한국기계연구소 소보
• /
• 통권17호
• /
• pp.29-38
• /
• 1987

A mechanical linkage system to measure the operating temperature of the piston is developed and installed to the engine. Actual temperature distribution is measured for comparison with the numerical results. Heat transfer at the piston is analyzed using an FEM program. Thermal boundary condition of piston surface is determined by analytical and empirical methods. The temperature distribution and the thermal deformation are obtained by the FEM program.

• 한국융합학회논문지
• /
• 제11권7호
• /
• pp.163-167
• /
• 2020

본 연구에서는 피스톤 헤드의 형상별 열응력해석을 진행하여 내구성이 있는 피스톤의 형상을 고찰하기 위한 연구를 진행하였다. 그 결과로서는 온도가 가해지는 부분에서부터 거리가 멀수록 낮은 온도를 볼 수 있다. 피스톤 헤드의 형상에 따라 열을 받는 면적이 다르기 때문에 피스톤 기둥 부분과 스커트부에 영향을 끼치게 된 점을 볼 수 있었다. 본 연구에서는 세 모델이 동일하게 피스톤 헤드의 중심부에서 가장 적은 응력이 나오는 것을 알 수 있었다. Model A는 다른 두 모델에 비해 항복이 발생하는 응력이 가장 작은 것을 알 수 있었다. Model B는 접시형 피스톤헤드로서 피스톤 헤드부가 오목한 형상으로 되어 있어 피스톤 헤드 중심부에서는 주변 부분에 영향을 가장 덜 끼치는 모델임을 알 수 있었다. Model C는 항복이 발생하게 되는 응력이 가장 크게 보였다. 또한 본 연구결과는 내구성이 있는 피스톤의 형상 설계에 유용하게 적용할 수 있다고 사료된다. 피스톤 헤드의 형상에 따른 열응력 해석을 적용함으로서, 본 연구가 미적인 융합에 부합된다고 사료된다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제9권2호
• /
• pp.143-152
• /
• 1985

In this paper, temperature distribution and thermal stress are investigated considering engine peak pressure and the time average temperature distribution in the piston under running conditions for the marine diesel engine. The induced stress are calculated by the Finite Element Method (FEM). The results obtained are summerized as follows. 1) The results calculated by the FEM present good agreement with other numerical solution in literatures. 2) It is comfirmed that the maximum compressive stresses are induced in the part of outside wall between the piston crown and the pin bush 3) In the axial direction, the hoop stresses are changed its sign at the portion of crown near the inner wall side. 4) Large gradient of temperature is shown in the piston crown near the side wall in the axial direction, in the part between the piston crown and the pin bush in radial direction. 5) In case of stress distribution of piston wall surface in the axial direction, the hoop stress is a little greater than axial stress, and the latter is greater than the radial stress.

• 한국정밀공학회지
• /
• 제19권11호
• /
• pp.146-159
• /
• 2002

An efficient method to predict the convection heat transfer coefficients on the top surface of the engine piston is proposed. The method is based on the inverse method of the thermal conduction problem and uses a numerical optimization technique. In the method, the heat transfer coefficients are numerically obtained so that the difference between analyzed temperatures from the finite element method and measured temperatures is minimized. The method can be effectively used to analyze the temperature distribution of engine pistons in case when application of prescribed-temperature boundary condition is not reasonable because of insufficient number of measured temperatures. A hollow sphere problem with an analytic solution is taken as a simple example and accuracy and efficiency is demonstrated. The method is applied to a practical large liquid petroleum gas(LPG) engine piston and the heat transfer coefficients on the top surface of the piston is successfully calculated. Resulting analyzed temperature favorably coincides with measured temperature.

• 한국자동차공학회논문집
• /
• 제6권2호
• /
• pp.100-106
• /
• 1998

The wide open throttle performance and piston temperatures were measured by the change of fuel : gasoline and liquefied petroleum gas(LPG). Bench test method was developed and experimented to study the effect of temperature on the formation of carbon deposit. The bench test results were confirmed by measuring the piston temperature and observing the deposit production rate at an actual engine running condition. Results show that if the fuel of spark ignition engine is changed from gasoline to LPG, the output power decreases about 10% and the piston temperatures increase about 40~55$^{\circ}C$. In actual engine tests, because of this temperature increase, it was observed that the quantity of carbon deposit in the top ring groove increased in a big degree. Consuquently, it is known that the fing sticking may occur if the gasoline engine was rebuilt to LPG fuelled engine. Therefore, in order to preserve the durability of LPG fuelled engine, it is necessary to lower the piston temperature by hardware modificationor to reduce the carbon deposit by the improvement of engine oil.