• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.5
• /
• pp.73-79
• /
• 2021

This study was carried out to analyze the properties of the gel propellant and spray characteristics according to the addition of fine particles. The multi-hole diameter was 0.4 mm to induce a high shear rate, and a kerosene gel propellant was prepared using 5 wt% of the Thixatrol ST and SUS304 of 100 nm. The experiment was conducted by fixing the supply pressure in the axial direction to 0.7 MPa and adjusting the supply pressure in the radial direction from 0.7 MPa to 2.1 MPa. Due to the addition of fine particles, pressure vibration during spraying, a small TMR(Total Momentum Ratio) of up to 0.19, and a phenomenon that the spraying angle rapidly increased to more than 70 degrees occurred.

• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.5 s.149
• /
• pp.578-585
• /
• 2006

Cavitation related erosion damages on semi-spade rudder generally occur at around leading edge of lower-face and behind gap of lower pintle. To get the idea of gap entrance profile for the latter case, a series of tests with large models has been carried out at MOERI. In the tests, the flow pattern around lower pintle have been investigated and visualized by high speed camera. Additionally, cavitation inception tests and pressure measurements have also been conducted for better comparison. As a result a new model (F rudder) has been developed. The new model turned out to have stable pressure distribution along the surface and so the cavitation inception speeds within ${\pm}5^{\circ}$ of rudder angle were delayed approx. 4 knots in average.

• Proceeding of EDISON Challenge
• /
• 2016.11a
• /
• pp.68-70
• /
• 2016

최근 저비용 및 재사용 발사체 개발 연구에 관한 관심이 증가하고 있는 추세인데, 이로 인해 노즐 내부에 핀틀 개념을 적용하여 발사체의 성능을 높이거나 스로틀링을 활용한 재사용 연구가 중요해지고 있다. 이 노즐 내부에 탑재된 핀틀 형상은 노즐 성능을 결정짓는데 핵심적인 역할을 하게 된다. 따라서 본 논문에서는 핀틀 형상에 따른 압력특성과 재순환 영역의 경향성을 확인하여 추후 저비용, 재사용 발사체 개발 연구의 기초자료로 활용하고자 한다. 해석 결과 핀틀 크기보다 핀틀 각도가 성능 변화에 더 민감한 변수로 판단되었다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.3
• /
• pp.87-95
• /
• 2016

A study on the effect of altitude-compensation and the possibility of throttling is performed by designing an E-D nozzle that is a type of altitude-compensation nozzles. In order to examine the effect of the altitude-compensation, a CFD analysis is conducted by using three kinds (sea level, altitude at 10 km and 16 km) of the atmosphere condition while maintaining the chamber pressure. Results show that the effective nozzle exit area is also gradually increased when the altitude get increased. Understanding the possibility of throttling, a CFD analysis is conducted by moving the location of the pintle. Just as same as a general pintle thruster, the chamber pressure and thrust are increased when the nozzle throat area get decreased.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.2
• /
• pp.152-159
• /
• 2018

A numerical simulation was conducted to establish the analysis methods of the unsteady conjugated heat transfer with a hot gas valve. Two methods are proposed to reduce the computational cost and analysis time of the unsteady conjugate heat transfer; namely, the multi-section analysis method and the one-way analysis method. The multi-section analysis method exhibits relatively high reliability. In the one-way analysis method, the unsteady conjugate heat transfer from the fluid domain to the solid domain was simulated from the analysis results of the steady-state flowfield. The incipient accuracy of the analysis results obtained by the one-way analysis method was slightly lower than that of the results obtained by the multi-section analysis method. However, the discrepancy became smaller with time, as the analysis progressed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.14-17
• /
• 2011

Numerical simulation was carried out for the SNECMA modulatable thrust devices, with four different nozzle contraction angle $45^{\circ}$, $60^{\circ}$, $83^{\circ}$, and $90^{\circ}$, respectively. Results show that $83^{\circ}$ nozzle contraction is better in that it comes up with good thrust level with small aerodynamic load.

• Journal of the Korean Society of Combustion
• /
• v.7 no.1
• /
• pp.44-51
• /
• 2002

This paper presents an atomization model for sprays under flash boiling conditions. The atomization is represented by the secondary breakup of a bubble/droplet system, and the breakup is considered as the results of two competing mechanisms, aerodynamic force and bubble growth. The model was applied to predict the atomization of a hollow-cone spray from pintle injector under flash boiling conditions. In the regimes this study considered, sprays are atomized by bubble growth, which produces smaller SMD#s than aerodynamic forces alone. With decreasing ambient pressures, the spray thickness, fuel vaporization rate and vapor radial penetration increases, and the drop size decreases. With increasing the fuel and ambient temperatures to some extent, the effect of flash boiling and air entrainment completely change the spray pattern.

• Journal of ILASS-Korea
• /
• v.6 no.3
• /
• pp.17-22
• /
• 2001

Recently LPG engine is developed to fulfill such new requirements as improved fuel efficiency in additional to further reduced exhaust emission. This experimental study is conducted to analyze spray characteristics for pintle type injector used in a LPLi (Liquid Phase LPG injection) engine. Since spray parameters including penetration length and spray angle make a role to design injector and engine intake system, spray visualization experiment is performed under atmosphere ambient and charging condition using Mie scattering method. From the experimental result under various LPG formation, the increased propane component decreases penetration length because boiling point of propane is lower than butane. To simulate intake charging condition in MPI engine, spray visualization is performed under high pressure condition. As a result, as ambient pressure is increased from atmosphere to 3.0 bar, penetration length is decreased. However, as ambient pressure is increased from atmosphere to 3.0 bar, spray angle is increased.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.389-392
• /
• 2000

This paper presents a performance Analysis of electrically exhaust gas recirculation valve using commercial electromagnetic simulation software, Flux2D. Under the assumption of 2D axi-symmetric magnetic field, the characteristics of EEGR valve by revising the design parameter, has ken investigated by estimating the variation of thrust force with respect to the pintle position. The mode shapes and the frequency response functions were computed by using three dimensional finite element modeling of the whole EEGR valve and their accuracies were verified with experimental FFT analysis technique.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2002.05a
• /
• pp.67-73
• /
• 2002

The characteristics of fuel spray influence on the engine performances such as power, fuel economy and emissions. therefore, the measurement of fuel spray characteristics is very important for the improvement of heat engine. The factor which controls the fuel spray is injection pressure, ambient pressure, engine speed et al.. In :his study, We measured spray angle, spray penetration and spray tip velocity considering injection pressure(10,14㎫), ambient pressure(3,4,5㎫), fuel pump speed(500,700,900rpm) in the high temperature and pressure chamber. Experimental results are summarized as follows: 1) Injection pressure influence on the characteristics of spray namely As Injection pressure Is increased, spray angle is decreased but spray penetration and spray tip velocity is increased. 2) Spray angle, spray penetration is increased by increasing the fuel pump speed. 3) Ambient pressure plays an important role in spray characteristics.