• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.2
• /
• pp.211-218
• /
• 2021

This paper deals with the computational work to characterize the formation and pinching of a plasma in an X-pinch configuration. A resistive magnetohydrodynamic model of a single fluid and two temperature is adopted assuming a hollow conical structure in the (r,z) domain. The model includes the thermodynamic parameter of tungsten from the corrected Thomas-Fermi EOS(equation of state), determining the average ionization charge, pressure, and internal energy. The transport coefficients, resistivity and thermal conductivity, are obtained by the corrected Lee & More model and a simple radiation loss rate by recombination process is considered in the simulation. The simulation demonstrated the formation of a core-corona plasma and intense compression process near the central region which agrees with the experimental observation in the X-pinch device at Seoul National University. In addition, it confirmed the increase in radiation loss rate with the density and temperature of the core plasma.

• Journal of Advanced Marine Engineering and Technology
• /
• v.15 no.3
• /
• pp.39-44
• /
• 1991

The purpose of this investigation is to examine the effects of spraying conditions on the mechanical properties of flame-sprayed titania ceramic coating layer. Titania ceramic was sprayed onto the mild steel substrate under the various spraying conditions. Spraying distances were 100, 150, 200, 250mm respectively and pinch air pressures were 0.2 0.3, 0.4 MPa at each spraying distance. The mechanical properties such as microhardness, adhesive strength and erosion wear resistance were tested for the specimens sprayed under the various spraying conditions above mentioned. The optimum operational conditions obtained through the experimental results were 150mm of spraying distance and 0.3 MPa of pinch air pressure.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.3
• /
• pp.415-425
• /
• 1996

This study presents an analytical method of solving the behaviors of arc plasma in a nozzle constricting transferred-type torch and purposes to obtain the basic data for the design of a plasma torch, which can be obtained from the temperature, pressure, velocities and voltage distributions. We have to solve some conservation equations simultaneously and need to know the exact thermal gas properties in order to obtain the correct behaviors of arc plasma. It is also necessary to give the relevant physical or geometric boundary conditions. For the simplicity of analysis, we assumed that (a) the plasma flow is laminar, (b)the local thermodynamic equilibrium, i.e. LTE, prevails over the entire arc column region. The electrode sheath effects were neglected and the nozzle area was excluded from the analysis by assuming that the current flow into the nozzle is zero. We solved the momentum transfer equation including the self-magnetic pinch effect, and obtained the temperature distribution from the energy conservation equation. From this temperature, we could get arc voltage distribution. (author). refs., figs., tabs.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.178.2-178.2
• /
• 2013

Conventional ultraviolets A,B,C are known to be very important factor of killing, changing surface properties of biological cells and materials. It is of great importance to investigate the influence of extreme ultraviolet (EUV) exposure on the biological cell. Here we have studied high density EUV plasma and its emission characteristics, which have been generated by plasma focus device with hypercycloidal pinch (HCP) electrode under various Ar gas pressures ranged from 30~500 mTorr in this experiment. We have also measured the plasma characteristics generated from the HCP plasma focus device such as electron temperature by the Boltzman plot, plasma density by the Stark broading method, discharge images by open-shuttered pin hole camera, and EUV emission signals by using the photodiode AXUV-100 Zr/C.

• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.307-308
• /
• 1987

A low-Pressure gap decoupling crow-bar switch was designed and operated to obtain prolonged current pulses by discharging 50kJ condeser banks. And air core Rogowski coil was used for measuring high current.

• Korean Journal of Materials Research
• /
• v.17 no.6
• /
• pp.308-312
• /
• 2007

Chromium oxide thin films have been deposited on silicon substrates using a tabletop 9kJ mathertyped plasma focus (PF) device. Before deposition, pinch behavior with gas pressure was observed. Strength of pinches was increased with increasing working pressure. Deposition was performed at room temperature as a function of working pressure between 50 and 1000 mTorr. Composition and surface morphology of the films were analyzed by Auger Electron Spectroscopy and Scanning Electron Microscope, respectively. Growth rates of the films were decreased with pressure. The oxide films were polycrystalline containing some impurities, Cu, Fe, C and revealed finer grain structure at lower pressure.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.1
• /
• pp.77-86
• /
• 1992

This paper discusses the thermodynamic study on the suction cooling-steam injected gas turbine cycle. The aim of this study is to improve the thermal efficiency and the specific output by steam injection produced by the waste heat from the waste heat recovery boiler and by cooling compressor inlet air by an ammonia absorption-type suction cooling system. The operating region of this newly devised cycle depends upon the pinch point limit and the outlet temperature of refrigerator. The higher steam injection ratio and the lower the evaporating temperature of refrigerant allow the higher thermal efficiency and the specific output. The optimum pressure ratios and the steam injection ratios for the maximum thermal efficiency and the specific output can be found. It is evident that this cycle considered as one of the most effective methods which can obtain the higher thermal efficiency and the specific output comparing with the conventional simple cycle and steam injected gas turbine cycle.

• The Korean Journal of Physiology
• /
• v.24 no.2
• /
• pp.305-317
• /
• 1990

The present study was performed to investigate modification in the electrophysiological characteristics of cat dorsal horn cells during neurogenic inflammation induced by mustard oil. The results obtained were summarized as follows: 1) Following subcutaneous injection of mustard oil the majority of wide dynamic range (WDR) cells (10/15 units) showed enhanced responses (80%) to brush, while the responses to all types of mechanical stiumli were enhanced in 3/15 units. One cell was further activated by pinch and the another was not affected at all after induction of inflammation. 2) The sensitization of WDR cell was resulted from subcutaneous injection of mustard oil either inside or outside of the receptive field (RF), whereas the spontaneous activity increased only after mustard oil was injected inside of the RF. 3) In the animal with inflammation the responses of high threshold (HT) cell to noxious stimulus were not altered, while HT cell responded to such mechanical stimulus as pressure which was usually ineffective in normal animals. 4) After induction of inflammation, low threshold (LT) cell appeared to be converted to WDR cell, showing responses not only to brush but also to pressure and pinch. 5) The mustard oil-induced inflammation enhanced responses of WDR and HT cells to the thermal stimuli and also resulted in a pronounced after-discharge in WDR cells. 6) After subcutaneous injection of lidocaine, the increased background activity of WDR cells due to inflammation was almost completely abolished. 7) A subcutaneous injection of mustard oil inside of the RF invariably desensitized the dorsal horn cells which receive sensory inputs from the inflamed RF. From the results of Present study it was revealed that a neurogenic inflammation induced by mustard oil resulted in an enhancement of responses of cat dorsal horn cells to mechanical and thermal stimuli.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1606-1608
• /
• 1994

A performance of the torch greatly depends on the plasma gas and the cooling gas. The plasma gas constricted by the nozzle concentrates electric power and momentum, so it can eject molten metal from a cut. As an electric arc constricted in a nozzle is more constricted through thermal pinch by the cooling gas, it is possible to transfer larger thermal concentration to the workpiece. The optimized parameter value in this study was given below. Plasma gas pressure is $4[kgf/cm^2]$ and gas mass flow is $30[{\ell}/min]$. Cooling gas pressure is $6[kgf/cm^2]$ and gas mass flow is $120[{\ell}/min]$.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.11
• /
• pp.699-707
• /
• 2017

This study presents a comparative thermodynamic analysis of subcritical and transcritical organic Rankine cycles for the recovery of low-temperature heat sources considering nine substances as the working fluids. The effects of the turbine inlet pressure, source temperature, and working fluid on system performance were all investigated with respect to metrics such as the temperature distribution of the fluids and pinch point in the heat exchanger, mass flow rate, and net power production, as well as the thermal efficiency. Results show that as the turbine inlet pressure increases from the subcritical to the supercritical range, the mismatch between hot and cold streams in the heat exchanger decreases, and the net power production and thermal efficiency increase; however, the turbine size per unit power production decreases.