• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12S
• /
• pp.1200-1204
• /
• 2003

In this study, in order to develop the low temperature sintering ceramics for multi-layer piezoelectric transformer, PSN-PZT system ceramics were manufactured as a function of CuO addition and their dielectric and piezoelectric characteristics were Investigated. CuO addition facilitated densification at low temperature due to the effect of Cu$_2$O-PbO liquid phase. Through the X-ray diffraction pattern study, absence of second phase unwanted was confirmed. Among the specimen to which CuO was added, the 0.6wt% CuO added specimen sintered at 900$^{\circ}C$ and 920$^{\circ}C$ showed the most excellent mechanical quality factor and electromechanical coupling factor, respectively. Besides the densification accelerator, CuO acted as a accepter and increased mechanical quality. Compared with the specimen with no addition sintered at 1150$^{\circ}C$ , the 0.6wt% CuO added specimen sintered at 920$^{\circ}C$ showed the appropriate dielectric and piezoelectric characteristics for multi-layer piezoelectric transformer.

• Membrane Journal
• /
• v.33 no.1
• /
• pp.13-22
• /
• 2023

Despite high capacity of lithium metal anode, its uncontrollable dendrite growth results in the poor electrochemical (EC) performance (low Coulomb efficiency and limited cycle stability) and unsafe operation. In this study, we demonstrated a lithium metal anode protected with BaTiO₃/PVDF based piezoelectric layer to enhance its EC performance by utilizing the locally polarized lithium metal after volume expansions. As-formed lithium metal electrode deposited with BTO@PVDF layer exhibited an enhanced Coulombic efficiency (> 98% for 100 cycles) and facilitated lithium ion diffusions (lithium diffusion coefficient: D_Li+), revealing the effectiveness of piezoelectric layer deposited lithium metal electrode approach.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.177-180
• /
• 2002

Thickness dependence of crystallographic orientation of diol based sol-gel derived PZT(52/48) films on dielectric and piezoelectric properties was investigated The thickness of each layer by one time spinning was about 0.2 $\mu\textrm{m}$, and crack-free films was successfully deposited on 4 inches Pt/Ti/SiO$_2$/Si substrates by 0.5 mol solutions in the range from 0.2 $\mu\textrm{m}$ to 3.8 $\mu\textrm{m}$. Excellent P-E hysteresis curves were achieved without pores or any defects between interlayers. As the thickness increased , the (111) preferred orientation disappeared from 1$\mu\textrm{m}$ to 3 $\mu\textrm{m}$ region, and the orientation of films became random above 3 $\mu\textrm{m}$. Dielectric constants and longitudinal piezoelectric coefficient d$\_$33/, measured by pneumatic method were saturated around the value of about 1400 and 300 pC/N respectively above the thickness of 0.8 7m. A micromachined piezoelectric cantilever have been fabricated using 0.8 $\mu\textrm{m}$ thickness PZT (52/48) films. PZT films were prepared on Si/SiN$\_$x/SiO$_2$/Ta/Pt substrate and fabricated unimorph cantilever consist of a 0.8 fm thick PZT layer on a SiNx elastic supporting layer, which becomes vibration when ac voltage is applied to the piezoelectric layer. The dielectric constant (at 100 kHz) and remanent polarization of PZT films were 1050 and 25 ${\mu}$C/$\textrm{cm}^2$, respectively. Electromechanical characteristics of the micromachined PZT cantilever in air with 200-600 $\mu\textrm{m}$ lengths are discussed in this presentation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.4 s.247
• /
• pp.409-419
• /
• 2006

The actuating performance of plate-type unimorph piezoelectric composite actuators having various stacking sequences was evaluated by three dimensional finite element analysis on the basis of thermal analogy model. Thermal residual stress distribution at each layer in an asymmetrically laminated plate with PZT ceramic layer and thermally induced dome height were predicted using classical laminated plate theory. Thermal analogy model was applied to a bimorph cantilever beam and LIPCA-C2 actuator in order to confirm its validity. Finite element analysis considering thermal residual deformation showed that the bending behavior of piezoelectric composite actuator subjected to electric loads was significantly different according to the stacking sequence, thickness of constituent PZT ceramic and boundary conditions. In particular, the increase of thickness of PZT ceramic led to the increase of the bending stiffness of piezoelectric composite actuator but it did not always lead to the decrease of actuation distance according to the stacking sequences of piezoelectric composite actuator. Therefore, it is noted that the actuating performance of unimorph piezoelectric composite actuator is rather affected by bending stiffness than actuation distance.

• International Journal of Safety
• /
• v.6 no.1
• /
• pp.22-25
• /
• 2007

Damping out high frequency low amplitude structural vibrations using PZT bimorph is presented. Static and Dynamic analyses of the piezoelectric bimorph bender were performed. Three layer piezoelectric actuators were modeled with SOLID5 coupled-field elements using ANSYS. Static deflection and modal analyses of the piezoelectric bimorph bender are presented. Proper tuning of the values of the resistor and inductor in the shunt circuit is required for maximum vibration suppression.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.51 no.4
• /
• pp.193-197
• /
• 2002

In this paper, the ultrasonic sensor for gas flowmeter was simulated, fabricated and measured according to the assembly step and the piezoelectric vibrator layers. The simulated resonant frequency and the measured resonant frequency were similar except two layer sensor. The simulated resonant frequency of three layer sensor was 48 kHz and the measured resonant frequency of three layer sensor was 45.2 kHz. From the results, the ultrasonic sensor for gas flowmeter could be designed and expected without fabrication.

• International Journal of Highway Engineering
• /
• v.19 no.5
• /
• pp.107-115
• /
• 2017

PURPOSES : The piezoelectric energy road analysis technology using a three-dimensional finite element method was developed to investigate pavement behaviors when piezoelectric energy harvesters and a new polyurethane surface layer were installed in field conditions. The main purpose of this study is to predict the long-term performance of the piezoelectric energy road through the proposed analytical steps. METHODS : To predict the stresses and strains of the piezoelectric energy road, the developed energy harvesters were embedded into the polyurethane surface layer (50 mm from the top surface). The typical type of triaxial dump truck loading was applied to the top of each energy harvester. In this paper, a general purpose finite element analysis program called ABAQUS was used and it was assumed that a harvester is installed in the cross section of a typical asphalt pavement structure. RESULTS : The maximum tensile stress of the polyurethane surface layer in the initial fatigue model occurred up to 0.035 MPa in the transverse direction when the truck tire load was loaded on the top of each harvester. The maximum tensile stresses were 0.025 MPa in the intermediate fatigue model and 0.013 MPa in the final fatigue model, which were 72% and 37% lower than that of the initial stage model, respectively. CONCLUSIONS : The main critical damage locations can be estimated between the base layer and the surface layer. If the crack propagates, bottom-up cracking from the base layer is the main cracking pattern where the tensile stress is higher than in other locations. It is also considered that the possibility of cracking in the top-down direction at the edge of energy harvester is more likely to occur because the material strength of the energy harvester is much higher and plays a role in the supporting points. In terms of long-term performance, all tensile stresses in the energy harvester and polyurethane layer are less than 1% of the maximum tensile strength and the possibility of fatigue damage was very low. Since the harvester is embedded in the surface layer of the polyurethane, which has higher tensile strength and toughness, it can assure a good, long-term performance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.249-250
• /
• 2006

In this study, we tried to Improve c-axis orientation of ZnO thin films used in a piezoelectric layer of FBAR devices. First. ZnO deposition conditions were determined by changing various conditions of RF sputter such as RF power, pressure and $O_2$ contents. The Piezoelectric layer was deposited on ZnO buffer layer of dense structure which was formed by ALD equipment. The c-axis orientation of ZnO piezoelectric layer was measured by XRD and we confirmed fine Grains and columnar structure by SEM, AFM.

• Journal of Mechanical Science and Technology
• /
• v.20 no.11
• /
• pp.1993-2001
• /
• 2006

The piezoelectric bimorph film, which, as an actuator, can generate more effective displacement than the usual PVDF film, is used to control the turbulent boundary-layer flow. The change of wall pressures inside the turbulent boundary layer is observed by using the multi-channel microphone array flush-mounted on the surface when actuation at the non-dimensional frequency $f_b^+$:=0.008 and 0.028 is applied to the turbulent boundary layer. The wall pressure characteristics by the actuation to produce local displacement are more dominantly influenced by the size of the actuator module than the actuation frequency. The movement of large-scale turbulent structures to the upper layer is found to be the main mechanism of the reduction in the wall- pressure energy spectrum when the 700$700{\nu}/u_{\tau}$-long bimorph film is periodically actuated at the non- dimensional frequency $f_b^+$:=0.008 and 0.028. The biomorph actuator is triggered with the time delay for the active forcing at a single frequency when a 1/8' pressure-type, pin-holed microphone sensor detects the large-amplitude pressure event by the turbulent spot. The wall-pressure energy in the late-transitional boundary layer is partially reduced near the convection wavenumber by the open-loop control based on the large amplitude event.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.1
• /
• pp.90-100
• /
• 1993

A finite element formulation of vibration control of a laminated plate with piezoelectric sensor/ actuators is presented. Classical lamination theory with the induced strain actuation and Hamilton's principle are used to formulate the equations of motion of the system. The total charge developed on the sensor layer is calculated from the direct piezoelectric equation. The equations of motion and the total charge are discretized with 4 node, 12 degrees of freedom quadrilateral plate bending elements with one electrical degree of freedom. The mass and stiffness of the piezoelectric layer are introduced by treating them as another layer in laminated plate. Piezoelectric sensor/actuators are distributed, but discrete due to the geometry of electrodes. By defining an i.d. number of electrode for each element, modelling of electrodes with variable geometry can be achieved. The static response of a piezoelectric bimorph beam to electrical loading and sensor voltage to given displacement are calculated. For a laminated plate under the negative velocity feedback control, the direct time response by the Newmark-.betha. method and damped frequencies and modal damping ratios by modal state space analysis are derived.