• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.6
• /
• pp.464-470
• /
• 2010

A new method for the poling of piezoelectric ceramics with an air insulation medium in stead of silicon oil is described. A similar variation of electromechanical coupling coefficient $K_t$, for an air medium is observed in comparison to that of the material poled by the conventional poling method using a silicon oil medium. Different poling parameters such as dielectric constant $\varepsilon^T$ and frequency deviation ${\Delta}f$ are studied as well as the influence on the aging effect. The required poling factors to achieve the optimal piezoelectric characteristics are electric field, 2 kV/mm, temperature $100^{\circ}C$, and poling time 30 Min. From this result electric field 3 kV/mm atmosphere airs there being will be able to use with the polarization insulation medium about the piezoelectric material, confirmed.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.36 no.7
• /
• pp.447-452
• /
• 1987

In this paper, the dependence of piezoelectric properties in the 0-3 composite system of piezoelectric-ceramics polymer materials on particle size of ceramics were investigated. Radial mode and thickness mode of composite were observed similar to single phase of piezoelectric ceramics. The measured values of dielectric constant and dissipation factor were dependent on particle size, which increased with the increasing particle size. the planar coupling factor, thickness coupling factor and thickness frequency constant with the particle size were almost constant, while planar frequency constant increased. The thickness coupling factor decreased with the increasing thickness of specimen. It is found that maximum voltage coeffidient was calculated on the specimen with particle size smallar than 46 ${\mu}m$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.701-704
• /
• 2003

In this study, to develop the low temperature sintering ceramics for multilayer piezoelectric transformer, PSN-PNN-PZT system ceramics were manufactured as a function of CuO addition. Its dielectric and piezoelectric characteristics were investigated. With increasing the amount of CuO addition, grain size was increased and density increased until 0.3wt% CuO. Taking into consideration electromechanical coupling factor(kp) of 0.53, mechanical quality factor(Qm) of 423 and ${\epsilon}r$ of 1759, it can be cincluded that the CuO 0.5wt% added composition sintered at $920^{\circ}C$ is suitable for piezoelectric transformer application if Qm is improved.

• Journal of the Korean Ceramic Society
• /
• v.34 no.5
• /
• pp.461-466
• /
• 1997

Dielectric and piezoelectric properties of (Pb1-1.5xLnx)(Ti0.98Mn0.02)O3 ceramics with x=0~0.2 have been investigated. Pb(Ti0.98Mn0.02)O3 showed poor sinterability and cracking on cooling, but the substitution of Nd3+ ions into Pb2+ sites resulted in dense microstructures without cracking through reducing crystallographic anisotropy. The Nd3+ substitution, however, deteriorated the temperature stability of the piezoelectric properties because of lowering the Curie point. Electromechanical anisotropy(Kt/Kp) indicated a maximum value of 10 when x=0.1. This result might be attributed to the counteracting effects that with increasing x, the lattice anisotropy decreases while the poling becomes easier due to the increase in O2- vacancy concentration. Thickness-shear mode resonators with (Pb0.85Nd0.1)(Ti0.98Mn0.02)O3 composition showed good resonant characteristics around 4.5 MHz.

• Proceedings of the KIEE Conference
• /
• 2005.11a
• /
• pp.157-159
• /
• 2005

In this study, in order to develop Pb-free piezoelectric ceramics, $[Li_{0.04}(Na_{0.44}K_{0.52)-(Nb_{0.86}Ta_{0.10}Sb_{0.04})]O_3$ ceramics were fabricated by conventional mixed oxide method and their piezoelectric characteristics were investigated according to the poling condition. The transition temperature from orthorhombic phase to tetragonal phase observed at $93[^{\circ}C]$ and Curie temperature was $346[^{\circ}C]$. At $50[^{\circ}C]$ poling temperature, dielectric constant, electromecha nical coupling factor kp, piezoelectric $d_{33}$ const ant, coercive field Ec, remanant polarization Pr and mechanical quality factor Qm showed the optimum value of 737, 0.45, 209[pC/N], 1l.34[kV/cm], $7.14[{\mu}C/cm^2]$ and 205, respectively.

• Electrical & Electronic Materials
• /
• v.10 no.9
• /
• pp.889-894
• /
• 1997

A miniaturized wind-mill type ultrasonic motor which has diameter in 12.7 mm and thickness in 2.0mm using PMN-PZT piezoelectric ceramics was fabricated. The wind-mill type ultrasonic motors has only three plate and of two wind-mill shape slotted metal endcaps a rotor whose end is hollowed out so that its periphery fits with the shape of the stator and a bearing to guide the rotor. A Finite Element Analysis was carried out to obtain the endcaps behavior under a radial displacement change of piezoelectric disk and to optimize the structure of the number of slots. Increasing the applied voltage the revolution speed of ultrasonic motors was increased. The maximum speed of 700 rpm and the maximum torque of 0.22 nN·m of the wind-mill type ultrasonic motors were obtained.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.249-250
• /
• 2006

Recently FPD(Flat Panel Display) is used in various field to display enormous information. So cutting technique of flat panel display is needed for producing variety display merchandises. In present, cutting methods of flat panel glass includes breaking process. But this process occurs many glass particles. This glass particles are directly related badness of merchandise and falling productivity. In this paper, to cut front substrate glass of LCD and to get optimized cutting condition are tried fur eliminating breaking process with developed glass cutting machine using a Piezoelectric ceramics actuator. It is known that the vibration of Piezoelectric Ceramic have effect in crack proceeding through the analysis of fracture section.

• Transactions on Electrical and Electronic Materials
• /
• v.2 no.3
• /
• pp.18-23
• /
• 2001

For the piezoelectric transformer application, Pb(Sb$\_$1/2/ Nb$\_$1/2/)O$_3$-Pb(Zr,Ti)O$_3$ ceramics were produced by attrition milling. Microstructural, dielectric and piezoelectric characteristics of the ceramics were investigated as a function of milling time. The particle size and grain size decreased while dielectric constant, density and mechanical quality factor (Q$\_$m/) increased with milling time. Temperature coefficient of resonant frequency (TCf$\_$r/) was shifted to positive side with increasing milling time. The attrition milling process proved to be one of the effective routes to produce transformers for high power application.

• Korean Journal of Materials Research
• /
• v.14 no.5
• /
• pp.334-337
• /
• 2004

Perovskite PMN-PZT-based ceramics were prepared and the$ MnO_2$ doping effects on their piezoelectric properties were investigated. Grain size decreased with increasing the $MnO_2$ content, and the pyrochlore phase was not identified in the sintered PMN-PZT ceramics with 0.01～1.0wt% $MnO_2$. Piezoelectric voltage and charge constants were reduced and mechanical quality factor increased with increasing the $MnO_2$ content. However, electromechanical coupling coefficient slightly decreased with increasing the MnO$_2$ content without regard to the grain size.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.711-714
• /
• 2000

In this study, the physical properties of the acoustic element and case with metal-piezoelectric ceramics were analyzed. The dielectric and piezoelectric properties of 0.5 wt% MnO$_2$and NiO doped 0.1Pb(Mg$\_$1/3Nb$\_$2/3)O$_3$-0.45PbTiO$_3$-0.45PbZrO$_3$ceramics were investigated aiming at acoustic transducer applications. The vibration characteristics for the laminated circular plate was analyzed for the various thickness and diameter of the piezoceramic layer and metal layer. Also, the acoustic characteristics for the geometrical form of case have been investigated. The design and fabrication method worked in this paper can be utilized in development of actuator and acoustic device.