• 대한기계학회논문집A
• /
• 제27권10호
• /
• pp.1772-1777
• /
• 2003

This paper presents the design, fabrication, and calibration of a piezoelectric polymer-based sensorized microgripper. Electro discharge machining technology is employed to fabricate super-elastic alloy based micro gripper. It is tested to present improvement of mechanical performance. For integration of force sensor on the micro gripper, the sensor design based on the piezoelectric polymer PVDF film and fabrication process are presented. The calibration and performance test of force sensor integrated micro gripper are experimentally carried out. The force sensor integrated micro gripper is applied to perform fme alignment tasks of micro opto-electrical components. It successfully supplies force feedback to the operator through the haptic device and plays a main role in preventing damage of assembly parts by adjusting the teaching command.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1988년도 전기.전자공학 학술대회 논문집
• /
• pp.802-805
• /
• 1988

The objective of the present study was to manufacture the piezoelectric composites of Lead Zirconate Titanate (PZT) - polymer for applications such as ultrasonic medical diagnosis and hydrophone. The PZT rod-polymer composites have been prepared with 4.5 to 57 volume percent PZT using 1.5 mm rod, so the connectivity pattern of the two phase is 1-3 type. The electromechanical coupling factors of radial mode ($k_{p}$) and thickness mode ($k_{t}$) were nearly independent of the volume percent PZT, which were 0.3 and 0.65, respectively. The acoustic impedance of the piezoelectric composites was measured by the resonance technique in the frequency range 50 KHz-1.5 MHz, which was in the range of 3.8 - 60 Mrayl.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1989년도 춘계학술대회 논문집
• /
• pp.63-65
• /
• 1989

Piezoelectric BaTiO$_3$-polymer composite were investigated for dielectric and piezoelectric properties with the barium titanate active particle size. Under the condition of the same density and ceramic volume ratio of composite, the dielectric and piezoelectric constant of composite are increasing as the ceramic particle size in composite are increasing. The surface layer model was quoted to explain these phenomena in our system and experimentally confirmed. The connectivity parameter of modified cube model of composite was calculated from the dielectric constant variation as their particle size. The connectivity parameter X and Y were 77.8% and 98.9% respectively. It means that the barium titanate particle distribution in composite nearly approach to the parallel mode. It was experimentally confirmed that the surface layer has low dielectric and nonferroelectric properties. Dielectric constant and thickness of surface layer were calculated from the equivalent circuit of composite.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1957-1959
• /
• 1996

In this paper, a piezoelectric micropump is fabricated and tested. The micropump consists of an actuator and two micronozzles have been made of silicon. It contains a piezoelectric polymer which allows opening and closing of the valves electrically. The actuator and the two micronozzles are fabricated by the anisotropic etch using EPW. Then, the fabricated actuator and the valves are anodically bonded with the pyrex glass which consists of the inlet and the outlet channels. The measured deflection of the piezoelectric polymer is $54\;{\mu}m$ at 1.6 kHz. The maximum pumping flow rate and the backward pressure of the micropump are $22\;{\mu}{{\ell}/min$, 8.7 Pa at 10 Hz, respectively.

• 한국고분자학회지:고분자과학과기술
• /
• 제1권6호
• /
• pp.342-357
• /
• 1990

• Carbon letters
• /
• 제25권
• /
• pp.1-13
• /
• 2018

Gold functionalized graphene oxide (GOAu) nanoparticles were reinforced in acrylonitrile-butadiene rubbers (NBR) via solution and melt mixing methods. The synthesized NBR-GOAu nanocomposites have shown significant improvements in their rate of curing, mechanical strength, thermal stability and electrical properties. The homogeneous dispersion of GOAu nanoparticles in NBR has been considered responsible for the enhanced thermal conductivity, thermal stability, and mechanical properties of NBR nanocomposites. In addition, the NBR-GOAu nanocomposites were able to show a decreasing trend in their dielectric constant (${\varepsilon}^{\prime}$) and electrical resistance on straining within a range of 10-70%. The decreasing trend in ${\varepsilon}^{\prime}$ is attributed to the decrease in electrode and interfacial polarization on straining the nanocomposites. The decreasing trend in electrical resistance in the nanocomposites is likely due to the attachment of Au nanoparticles to the surface of GO sheets which act as electrical interconnects. The Au nanoparticles have been proposed to function as ball rollers in-between GO nanosheets to improve their sliding on each other and to improve contacts with neighboring GO nanosheets, especially on straining the nanocomposites. The NBR-GOAu nanocomposites have exhibited piezoelectric gauge factor (${GF_{\varepsilon}}^{\prime}$) of ~0.5, and piezo-resistive gauge factor ($GF_R$) of ~0.9 which clearly indicated that GOAu reinforced NBR nanocomposites are potentially useful in fabrication of structural, high temperature responsive, and stretchable strain-sensitive sensors.

• 한국전기전자재료학회논문지
• /
• 제36권6호
• /
• pp.620-626
• /
• 2023

Energy harvesting technology, which converts wasted energy sources in everyday life into usable electric energy, is gaining attention as a solution to the challenges of charging and managing batteries for the driving of IoT sensors, which are one of the key technologies in the era of the fourth industrial revolution. Hybrid energy harvesting technology involves integrating two or more energy harvesting technologies to generate electric energy from multiple energy conversion mechanisms. In this study, a hybrid energy harvesting device called TMPPEG (thermo-magneto-piezoelectric-pyroelectric energy generator), which utilizes low-grade waste heat, was developed by incorporating PVDF polymer piezoelectric components and optimizing the system. The variations in piezoelectric output and thermoelectric output were examined based on the spacing of the clamps, and it was found that the device exhibited the highest energy output when the clamp spacing was 2 mm. The voltage and energy output characteristics of the TMPPEG were evaluated, demonstrating its potential as an efficient hybrid energy harvesting component that effectively harnesses low-grade waste heat.

• Composites Research
• /
• 제34권6호
• /
• pp.357-372
• /
• 2021

에너지 수확장치는 석유자원의 고갈로 인한 자원난을 해결할 수 있는 대안으로 유망하다고 알려져 있다. 기계적 움직임을 전기 에너지로 전환할 수 있는 압전 소자들의 한계(환경오염 및 낮은 기계적 특성)를 극복하기 위하여, 고분자 기지재 기반 복합재료 압전 에너지 수확장치에 대한 많은 연구들이 수행되었다. 본 논문에서는 사용된 재료 및 공정에 기초하여, 보고된 압전 복합재료의 출력 성능 및 관련된 응용 분야를 검토하였다. 압전 필러는 티탄산 지르콘산 연 및 티탄산바륨 기반의 세라믹 필러뿐만 아니라, 친환경, 생체적합성 및 유연성 측면에서 유리한 산화아연을 검토하였다. 기지재는 폴리비닐리덴플로오라이드 및 공중합체로 구성된 압전 고분자 및 에폭시 및 폴리디메틸실록산 기반의 유연한 고분자로 분류하여 복합재료의 압전 시너지 및 높은 외력 적용에 의한 압전 출력 향상을 논의하였다. 또한, 금속 혹은 탄소 소재 기반 2차 필러의 적용에 의한 복합재료의 전도성 혹은 기계적 특성의 향상이 압전 수확장치의 출력 성능에 미치는 영향을 복합재료의 구조 측면에서 검토하였다. 향상된 성능으로 소형 전자기기, 스마트 센서, 의학 분야 등에 응용 가능한 복합재료 기반 압전 수확장치는 미래의 일상에서 접할 수 있는 무선 전자 장치의 전원으로써 잠재적인 통찰을 제공할 수 있다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.297.2-297.2
• /
• 2013

Scavenging electricity from wasteful energy resources is currently an important issue and piezoelectric nanogenerators (NGs) based on zinc oxide (ZnO) are promising energy harvesters that can be adapted to various portable, wearable, self-powered electronic devices. Although ZnO has several advantages for NGs, the piezoelectric semiconductor material ZnO generate an intrinsic piezoelectric potential of a few volts as a result of its mechanical deformation. As grown, ZnO is usually n-type, a property that was historically ascribed to native defects. Oxygen vacancies (Vo) that work as donors exist in ZnO thin film and usually screen some parts of the piezoelectric potential. Consequently, the ZnO NGs' piezoelectric power cannot reach to its theoretical value, and thus decreasing the effect from Vo is essential. In the present study, c-axis oriented insulator-like sputtered ZnO thin films were grown in various temperatures to fabricate an optimized nanogenerator (NGs). The purity and crystalinity of ZnO were investigated with photoluminescence (PL). Moreover, by introducing a p-type polymer usually used in organic solar cell, it was discussed how piezoelectric passivation effect works in ZnO thin films having different types of defects. Prepared ZnO thin films have both Zn vacancies (accepter like) and oxygen vacancies (donor like). It generates output voltage 20 time lager than n-type dominant semiconducting ZnO thin film without p-type polymer conjugating. The enhancement is due to the internal accepter like point defects, zinc vacancies (VZn). When the more VZn concentration increases, the more chances to prevent piezoelectric potential screening effects are occurred, consequently, the output voltage is enhanced. Moreover, by passivating remained effective oxygen vacancies by p-type polymers, we demonstrated further power enhancement.

• Macromolecular Research
• /
• 제17권3호
• /
• pp.197-202
• /
• 2009

Solution-based, direct-write patterning by an automated, computer-controlled, inkjet technique is of particular interest in a wide variety of industrial fields. We report the construction of three-dimensional (3D), micro-patterned structures by polymer inkjet printing. A piezoelectric, drop-on-demand (DOD) inkjet printing system and a common polymer, PVA (poly(vinyl alcohol)), were explored for 3D construction. After a systematic preliminary study with different solvent systems, a mixture of water and DMSO was chosen as an appropriate solvent for PVA inks. The use of water as a single solvent resulted in frequent PVA clogging when the nozzles were undisturbed. Among the tested polymer ink compositions, the PVA inks in a water/DMSO mixture (4/1 v/v) with concentrations of 3 to 5 g/dL proved to be appropriate for piezoelectric DOD inkjet printing because they were well within the proper viscosity and surface tension range. When a dot was printed, the so-called 'coffee-ring effect' was significant, but its appearance was not prominent in line printing. The optimal polymer inkjet printing process was repeated slice after slice up to 200 times, which produced a well-defined, 3 D micro-patterned surface. The overall results implied that piezoelectric DOD polymer inkjet printing could be a powerful, solid-freeform, fabrication technology to create a controlled 3D architecture.