• Journal of the Korean Ceramic Society
• /
• v.50 no.6
• /
• pp.545-550
• /
• 2013

Piezoelectric PMN-29PT single crystal multilayer actuators [100 $mm^2$ in cross section and 22 mm in length] are designed and fabricated by stacking square plates [$10{\times}10{\times}0.5(t)\;mm^3$] of PMN-29PT single crystals having a $d_{33}$ of about 1,500 pC/N. The characteristics of PMN-29PT multilayer actuators are compared with those of P-025.40P multilayer PZT ceramic actuators [490 $mm^2$ in cross section and 60 mm in length] produced by PI in Germany. Even though the total volume of the PMN-29PT single crystal multilayer actuator is only about 7.5% of that of the P-025.40P ceramic multilayer actuator, PMN-29PT single crystal multilayer actuators are expected to show very similar properties to P-025.40P ceramic actuators in terms of static stroke and blocking force. Therefore, on the basis of their smaller mass and volume compared to the conventional PZT ceramic multilayer actuators, piezoelectric PMN-29PT single crystal multilayer actuators have significant potential regarding the development of various high performance actuators for aerospace subsystems.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.1
• /
• pp.30-34
• /
• 2019

A newly proposed T-shape piezoelectric actuator, composed of piezoelectric benders, was designed and studied. This actuator has four legs, and can walk in both forward and backward directions. The piezoelectric actuator has a simple structure and can be easily fabricated. It consists of a piezoelectric bender and a joint. The piezoelectric bender is composed of carbon and ceramic materials. Therefore, there is an advantage in that it can be fabricated on a very small scale. Elliptical displacements of the piezoelectric actuators were analyzed by finite element analysis. Elliptical motion at the tip occurred at two voltages having a 90-degree phase difference. Based on the finite element analysis results, prototype actuators with maximum displacements were fabricated, and the characteristics of their movements were characterized.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.8
• /
• pp.880-888
• /
• 2007

This article describes the load capability of bending piezoelectric actuators with a thin sandwiched PZT plate in association with the stored elastic energy induced by an increased dome height after a curing process. The stored elastic energy within the actuators is obtained via a flexural mechanical bending test. The load capability is evaluated indirectly in terms of an actuating displacement with a load of mass at simply supported and fixed-free boundary conditions. Additionally, a free displacement under no load of mass is measured for a comparison with an actuating displacement. The results reveal that an actuator with a top layer having a high elastic modulus and a low coefficient of thermal expansion exhibits a better performance than the rest of actuators in terms of free displacement as well as actuating displacement due to the formation of the large stored elastic energy within the actuator system. When actuators are excited at AC voltage, the actuating displacement is rather higher than the free displacement for the same actuating conditions. In addition, the effect of PZT ceramic softening results in a slight reduction in the resonance frequency of each actuator as the applied electric field increases. It is thus suggested that the static and dynamic actuating characteristics of bending piezoelectric composite actuators with a thin sandwiched PZT plate should be simultaneously considered in controlling the performance.

• Smart Structures and Systems
• /
• v.5 no.3
• /
• pp.241-260
• /
• 2009

Shape control of flexible structures using piezoelectric materials has attracted much attention due to its wide applications in controllable systems such as space and aeronautical engineering. The major work in the field is to find a best control voltage or an optimal placement of the piezoelectric actuators in order to actuate the structure shape as close as possible to the desired one. The current research focus on the investigation of static shape control of intelligent shells using spatially distributed piezoelectric curve beam actuators. The finite element formulation of the piezoelectric model is briefly described. The piezoelectric curve beam element is then integrated into a collocated host shell element by using nodal displacement constraint equations. The linear least square method (LLSM) is employed to get the optimum voltage distributions in the control system so that the desired structure shape can be well matched. Furthermore, to find the optimal placement of the piezoelectric curve beam actuators, a genetic algorithm (GA) is introduced in the computation model as well as the consideration of the different objective functions. Numerical results are given to demonstrate the validity of the theoretical model and numerical algorithm developed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.10 s.181
• /
• pp.2502-2512
• /
• 2000

Truss structures are widely used in many space structures, such as large antenna systems, space stations, precision segmented telescopes because they are light in weight and amenable in assembly or deployment. But, due to the low damping capacity, they remain excited for a long time once disturbed. These structural vibrations can reduce life of the structures and cause unstable dynamic characteristics. In this research, vibration suppression experiment has carried out with a three-dimensional 15-member truss structure using two piezoelectric actuators. Piezoelectric actuators which consist of stacks of thin piezoelectric material disks are directly inserted to the truss structure collocated with the strain sensors. Each actuator is controlled digitally in decentralized manner, based on local integral and proportional feedback. The optimal positions of the actuators are determined by the modal damping ratio and the control force. Numerical simulation has carried out to determine optimal position of each actuator.

• Structural Engineering and Mechanics
• /
• v.14 no.1
• /
• pp.21-38
• /
• 2002

A control algorithm combining viscous and non-linear Reid damping mechanisms has been recently proposed by the authors to command active friction dampers. In this paper, friction dampers and the proposed algorithm are applied to control the seismic responses of a nonlinear 20-story building. Piezoelectric stack actuators are used to implement the control algorithm. The capacity of each damper is determined by the practical size of piezoelectric actuators and the availability of power supply. The saturation effect of the actuators on the building responses is investigated. To minimize the peak story drift ratio or floor acceleration of the building structure, a practical sequential procedure is developed to sub-optimally place the dampers on various floors. The effectiveness of active friction dampers and the efficiency of the proposed sequential procedure are verified by subjecting the building structure to four earthquakes of various intensities. The performance of 80 dampers and 137 dampers installed on the structure is evaluated according to 5 criteria. Numerical simulations indicated that the proposed control algorithm effectively reduces the seismic responses of the uncontrolled 20-story building, such as inelastic deformation. The sub-optimal placement of dampers based on peak acceleration outperforms that based on peak drift ratio for structures subjected to near-fault ground motions. Saturation of piezoelectric actuators has adverse effect on floor acceleration.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.24 no.2
• /
• pp.193-200
• /
• 2014

Piezoelectric actuators have been widely used in various applications because they have many advantages such as fast response time, repeatable nanometer motion, and high resolution. However Piezoelectric actuators have the strong hysteresis effect. The hysteresis effect can degrade the performance of the system using piezoelectric actuators. In past study, the parameters of the inverse hysteresis model are computed from the identified parameters using the Generalized Prandtl-Ishlinskii(GPI) model to cancel the hysteresis effect, however according to the identified parameters there exist the cases that can't form the inverse hysteresis loop. Thus in this paper the inverse hysteresis modeling mothod is proposed using the Inverse Generalized Prandtl-Ishlinskii(IGPI) model to handle that problem. The modeling results are verified by experimental results using various input signals.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.785-789
• /
• 2001

Piezoelectric actuators are characterized by non-linear dynamics and high frequency oscillations of the piezocrystal. Both properties have to be taken into consideration when optimizing real time systems. Taking benefit of the almost linear behaviour between charge and strain, current source fed piezoelectric actuators are given preference for high dynamic applications. Here special emphasis is put on current sources for multi-actuator systems and the controller design for optimal system integration of the actuator. It is shown that sliding mode operation of the converter system offers good possibilities to guaranty high accuracy and dynamics of the actuators system. The presented multi-actuator system is used for positioning and vibration damping in flexible mechanical systems.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.776-778
• /
• 2003

In the paper, the novel linear ultrasonic motor for precision position control was designed and fabricated. It was composed of two piezoelectric actuators with longitudinal ultrasonic fluctuations and shaking beam. When two AC electric fields ($Usin{\omega}t$, $Ucos{\omega}t$) were applied in two piezoelectric actuators respectively, the middle part of shaking beam had an elliptical trajectory. According to experimental results, good symmetrical characteristic of two piezoelectric actuators were obtained.

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.4
• /
• pp.239-246
• /
• 2000

This paper investigates optimal locations of piezoelectric actuators and sensors on a thin plate. To locate actuators and sensors properly is important in controlling modal vibrations well. A piezoelectric sensitivity index is introduced to select optimal locations for vibration control of each mode. The sensitivity expresses the efficiency of actuating and sensing modal forces according to locations of a piezoelectric material on a plate. The piezoelectric sensitivities for two types of plate, an all-clamped plate, and a free-free plate, are derived theoretically and are verified experimentally. Also, its usefulness Is experimentally shown to control vibration of the all-clamped plate with piezoelectric materials.