• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.454-457
• /
• 1995

In optical disc system, tracking actuator is consisted of coarse actuator and fine tracking actuator. This, two-stage actuator, requires many devices and two servos for large stroke and precisional displacement. These complicate configuration increases moving mass. So dynamic characteristics become bad, that is, sensitivity of high frequency gain decrease. In this paper, frequency performance is willing to be better as so one dimensional tracking actuator is designed. In order to investigate the performance of the proposed tracking actuator, the Bode diagram is plotted with Dynamic analyzer and friction characteristic is explained. Finally, tracking error performance is ins investigated into 0.1 .mu.m resolution with MATLAB simulation.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.618-621
• /
• 2001

The proposed lever actuator has no friction and mass balance characteristics in motion, which are adapt to high-speed and high-density optical disk system. This paper discussed about the theoretical analysis of the lever structure. The modeling of the lever actuator is found. Using the Newton's method, the motion of equation is deduced through the constraint equations and equilibrium equations in three directions (focusing, tracking and tilting). From the above analysis, we know that the shape of the hinge is the very important parameter on determining the performance of the lever actuator, and the actuator has the 2nd order system characteristics. And the first resonant frequency in transmissibility is dependent to the rigidity of the lever while the first transmissibility resonance of conventional actuators is dependent to the first natural resonance of those actuators. This means that the lever actuator is more stable to the external vibration.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2007년도 The 1st International Symposium on Advanced Magnetic Materials
• /
• pp.253.2-253.2
• /
• 2007

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.664-669
• /
• 2003

This paper proposes a swing-arm type dual-stage actuator, which consists of a PZT actuator for fine motion and a VCM(Voice Coil Motor) for coarse motion, for SFF ODD(Small Form Factor Optical Disk Drive), in order to achieve fast access speed and precise track following control. We focus our attention on the design and control of the PZT actuator, because there have been a lot of previous researches related to the VCM and dual-stage actuators. Due to the dual cantilever structure, the PZT actuator can generate precise translational tracking motion at its tip where optical pickup is attached at, and the effect of hysteric behavior of the PZT element is reduced. The dynamic model of the PZT actuator is derived by using the Hamilton's principle, and verified by comparing with the experimental frequency response. The sliding mode control is designed in order to be robust against modeling uncertainties. Simulations and experimental results confirm the effectiveness of the suggested control scheme.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.407-412
• /
• 2004

본 연구에서는 PMN-PT bimorph actuator를 이용하여 초소형 광디스크 드라이브용 광픽업 구동기를 제작하였다. 최근에 휴대용 기기에서의 고용량 정보 저장기기에 대한 필요성이 대두됨에 따라 착탈식이 가능한 수 기가급 초소형 광디스크 드라이브가 개발중에 있다. PMN-PT는 약 1.5kV/cm 이하의 전기장에서는 PZT같은 압전 소자와 마찬가지로 입력 전압에 대한 변형률이 선형성을 나타내는데, 사용된 PMN-PT는 PZT의 약 3배 가까운 압전 상수값을 나타내었다. 보 끝단에 외부 힘이 작용할 때 PMN-PT bimorph 구동기가 낼 수 있는 수직 방향의 힘과 변위에 대해서 일반적인 적층 형태로 이론적인 해석을 수행 하였다. 그리고 이 bimorph로 구동될 Cymbal 형태의 변위 확대 기구의 변위에 대한 이론적인 모델을 제시하고, 이를 이용하여 2개의 bimorph로 2축을 동시에 구동하는 픽업 구동기를 제작하였다. 3개의 제작된 prototype으로 실험을 수행하여 예상 변위량과 잘 일치함을 보였다. 또한, 상용 해석 프로그램인 Matlab과 Ansys를 이용하여 Cymbal 확대 기구의 여러 파라미터에 따른 구동 성능의 민감도를 확인해 보았다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.782-787
• /
• 2002

In optical disk drives (ODD), the demands of high data density and high speed have been increasing rapidly to achieve high data capacity and data transfer rate. The short wavelength laser, High NA objective lens, and high track following performance are needed to raise data density and data rate. For high-performance actuator, the improvement of linearity and acceleration become more important. Also, 3-axis actuator for active tilt compensation is introduced to overcome the decrease in disk tilt tolerance which is induced by short wavelength laser. In this paper, a hybrid type 3-axis actuator is presented and a new yoke structure, which can reduce the interaction between yoke and moving magnet, is designed to keep the efficiency of magnetic circuit. Experimental results show the validity of the yoke in the hybrid type actuator.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권5호
• /
• pp.249-252
• /
• 2001

The paper represents the design and fabrication of an electrostatic micro actuator with $p^+$,/TEX> Si cantilevers. The micro actuator consists of a plate suspended by four $p^+$,/TEX> silicon cantilevers and an electrode on a glass substrate. The $p^+$,/TEX> Si structure is fabricated by the boron diffusion process and the anisotropic wet etch process. The cantilevers of the micro actuator curl down because of the residual stress gradient in $p^+$,/TEX> silicon. When the electrostatic forec is applied to the $p^+$,/TEX> cantilevers, the vertical displacement of the plate can be achieved. The deflection of the cantilever due to the residual stress gradient and the vertical displacement by electrostatic force were calculated. The displacement of the plate was measured with a laser displacement meter for various input voltages and frequencies. The feasibility of the proposed micro actuator for the applications to optical pickup devices or optical communication devices was confirmed by the experiments.

• 소음진동
• /
• 제8권3호
• /
• pp.533-541
• /
• 1998

Recently, optical disk drives are increasingly demanded to have higher speed as well as high information density, especially for applications like CD ROM drives. To this end, improvement of their optical pickup structure and control is recognized the very challenging issue. In this paper, the pickup is first analytically modelled in a plane to describe its coupled auto-focusing and auto-tracking motions. Subsequently, the model is linearized and combined with actuator dynamics for the auto-focusing system. With its unmeasurable parameters being estimated based on experimental data, an approximate I-DOF linear model is obtained neglecting the coupling term. To design the high speed and robust positional servo controller realistic design specifications are addressed, and H control method is employed based on the approximate model. Finally, taking the pickup in a commerical high speed CD ROM drive as an example performance of the designed controller is verified through realtime experiments.

• 한국소음진동공학회논문집
• /
• 제15권2호
• /
• pp.232-238
• /
• 2005

This paper proposed an optimal plate spring design for the optical pickup suspension. This method requires an analytic solution of plate spring suspension and it can be obtained by Castigliano's theorem and moment equilibrium. However, it is very complex due to the many design variables coupled and some constraints such as pitching angle in focusing motion caused by the characteristics of plate spring. Because of the complex formulation of the analytical solution that is used as the design objective, the genetic algorithm is used to find the optimal design value satisfying design constraints.

• 한국소음진동공학회논문집
• /
• 제14권12호
• /
• pp.1255-1260
• /
• 2004

A moving-magnet type pickup actuator has an assembly error. That is, the actuating Part of an actuator is shifted from initial position after we assemble it into yoke. This Is the result of an effect of magnetic force between magnet and yoke. We performed magnetic-analysis using FEA. As a result of simulation, we improved the assembling efficiency for moving-magnet type actuator.