• Journal of the Korean Wood Science and Technology
• /
• v.44 no.5
• /
• pp.776-784
• /
• 2016

In this study, green Larix kaempferi lumber was heat-treated by using superheated steam (SHS) at a pilot scale and then various physico-mechanical properties of the heat-treated wood were evaluated and compared with the properties of conventional hot air (HA) heat-treated wood. Decay resistance of brown rot fungi and compressive strength parallel to the grain of the SHS heat-treated wood without occurrence of drying check from green lumber were increased. On the other hand, density, equilibrium moisture content, shrinkage, and bending strength of the SHS heat-treated wood were lower than those of the conventional HA heat-treated wood. Because heat transfer and thermal hydrolysis of SHS heat treatment was accelerated by a large amount of water, the effect of SHS heat treatment on the physico-mechanical properties was higher than that of HA heat treatment at the similar conditions of temperature and time. From the results of this study, because green lumber can be heat-treated without occurrence of cracks or checks by using SHS and similar heat treatment effect on the physico-mechanical properties of wood can be produced despite a low temperature or short time of heat treatment, it is expected that heat time and energy consumption could be reduced by using SHS.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.3
• /
• pp.984-990
• /
• 2014

Polymers are the most commonly used di-electrics because of their reliability, availability, ease of fabrication and cost. The commercial and industrial demand for advanced polymeric materials which are capable of being used in harsh environment is need of the hour. The study of the effect of electron beam irradiation on polymeric materials is an area of rapidly increasing interest. This paper discusses the resultant beneficial effects of electron beam irradiation on the SiR-EPDM blend having 50:50 composition. The changes in mechanical and electrical properties of SiR-EPDM blend which are exposed to three different doses of electron beam radiation namely 5 Mrad, 15 Mrad and 25 Mrad are presented. The irradiated blends are analyzed for their electro-mechanical and physico chemical properties. The electrical changes induced by irradiation are investigated by arc resistance, surface resistivity and volume resistivity measurements as per ASTM standards. The mechanical changes are observed by the measurement of tensile strength and elongation at break. Physico chemical investigation has been done using the FTIR, in order to investigate the irradiation induced chemical changes.

• Advances in concrete construction
• /
• v.9 no.1
• /
• pp.9-22
• /
• 2020

The present work looks at the possibilities of recycling more than once demolished concrete as coarse aggregates, to produce new concrete. Different concrete mixes were made with substitutions of 50%, 75% and 100% of recycled concrete aggregates respectively as coarse aggregates. The physico-mechanical characterization tests carried out on the recycled concrete aggregates revealed that they are suitable for use in obtaining a structural concrete. The resulting concrete materials had rheological parameters, compressive strengths and tensile strengths very slightly lower than those of the original concrete even when 100% of two cycles recycled concrete aggregates were used. The durability of the recycled aggregates concrete was assessed through water permeability, water absorption and chemical attacks. The obtained concretes were thought fit for use as structural materials. A linear regression was developed between the strength of the material and the number of cycles of concrete recycling to anticipate the strength of the recycled aggregates concrete. From the results, it appear clear that recycling demolished concrete represents a valuable resource for aggregates supply to the concrete industry and a the same time plays a key role in meeting the challenge for a sustainable development.

• Korean Journal of Metals and Materials
• /
• v.46 no.7
• /
• pp.437-442
• /
• 2008

The synthesis and hydration of Calcium Sulfo Aluminate[$3CaO{\cdot}3Al_2O_3{\cdot}CaSO_4(C_4A_3{\overline{S}})$, CSA cement utilizing secondary steelmaking refining slags is studied for recycling the discarded steel plant wastes to meet the environmental requrations imposed on the steel industry. Raw materials of secondary refining slag, lime sludge, gypsum and bauxite were prepared to be sintered at $1,250^{\circ}C$. The sintered samples were hydrated for 1, 3 and 7 days to evaluate the mineralogical and physico-mechanical properties. The hydration products evaluated with the aid of SEM and XRD analyses confirmed the formation and the continuing growth of ettringite phase with the further hydration times, which plays a role in developing the early strength and the expansion properties of cements. The physico-mechanical properties of hydrated CSA products employing the recycled steelmaking refining slags determined in terms of compressive strength and linear expansion of hydrated products are found to be superior to those of the Ordinary Portland Cement(OPC) or the other commercial CSA cements.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.2
• /
• pp.39-50
• /
• 2007

The purpose of this study was to investigate the physico-mechanical properties and characteristics on reduction of formaldehyde and total volatile organic compound (TVOC) emission from particleboard (PB) with added volcanic pozzolan. Pozzolan was added as a scavenger at the level of 1, 3, 5, and 10 wt.% of urea formaldehyde (UF) resin for PB manufacture. The moisture content, density, thickness swelling, water absorption and physical properties of PBs were examined. Three-point bending strength and internal bond strength were determined using a universal testing machine. Formaldehyde and TVOC were determined by desiccator and 20L small chamber methods. With increasing pozzolan content the physical and mechanical properties of the PBs were not significantly changed, but formaldehyde and TVOC emissions were decreased. Because pozzolan has a rough and irregular surface with porous form, it can be used as a scavenger for PBs at a content up to 10 wt.% without any detrimental effect on the physical and mechanical properties.

• Advances in concrete construction
• /
• v.8 no.3
• /
• pp.199-206
• /
• 2019

High performance sandcretes (HPS) are new concretes characterized by particles having a diameter less than 5 mm, as well as very high mechanical strength and durability. This work consists in finding solutions to make sandcretes with good physico-mechanical and durability properties for this new generation of micro-concrete. However, upgrading ordinary sandcrete into high performance sandcrete (HPS) requires a thorough study of formulation parameters (equivalent water/binder ratio, type of cement and its dosage, kind and amount of super plasticizer, and gravel/sand ratio). This research study concerns the formulation, characterization and durability, in a sulphate environment, of a high performance sandcrete (HPS), made from local materials. The obtained results show that the rheological properties of fresh concrete and mechanical strength differ with the mineralogy, density and grain size distribution of sands and silica fume used.

• Applied Chemistry for Engineering
• /
• v.2 no.4
• /
• pp.356-362
• /
• 1991

The physico-mechanical properties of NR/BR blend were measured, and the results were interpreted in terms of the crosslink density with cure system. The cure rate, maximum torque and crosslink density increase with the content and ratio of curative for cure system. Hardness, 300 % tensile modulus, rebound and wear resistance increase with crosslink density of the vulcanizate but heat build-up and tan $\delta$ at $60^{\circ}C$ decrease. It is expected that semi-EV(efficient vulcanization) cure system is appropriate for application in tire tread of truck/bus in which load bearing property is impotant.

• Advances in concrete construction
• /
• v.5 no.6
• /
• pp.639-658
• /
• 2017

Very limited studies have been accomplished concerning the historical structures around Harran area. Collected mortar samples from the historic structures in the area were tested to explore their mechanical, chemical and mineralogical properties. Mortar samples from three different points of each historical structure were taken and specified in accordance with the related standards taking into consideration their mechanical, chemical and mineralogical properties. By means of SEM-EDX the presence of organic fibres and calcite, quartz, plagioclase and muscovite minerals has been examined. Additionally, by means of XRF analysis, oxide ($SiO_2$, $Al_2O_3$, and $Fe_2O_3$) percentages of mortar ingredients have been specified, also. According to the test results obtained, it was confirmed that the mortars had densities ranging between $1.51-2.10g/cm^3$, porosity values ranging between 8.89-35.38% and compressive strengths ranging between 5.02-5.90 MPa. Specimen HU, which has the highest durability and lowest water absorption and porosity, was the mortar taken from the most intact building in the mosque complex. This result is most likely due to the very little fine aggregate content of HU. In contrast, HUC mortars with a small amount of fine particles and brick contents yielded slightly lower compressive strengths. The interesting point of this study is the mineralogical analysis results and especially the presence of ettringite in these historic mortars linked to the use of pozzolanic materials. Survival of these historic structures in Harran Area through centuries of use and, also, having been subjected to many earthquakes can probably be explained by these properties of the mortars.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.998-999
• /
• 2006

A new mathematical simulation technique for physico-mechanical properties of multi-component powder materials is proposed in this paper. The main advantage of the technique is that finite elements representing different components are placed into a common mesh and may exchange their properties. The output data are properties of material after sintering. The technique allows us to investigate the influence of each component of a material on the properties and distribution of properties inside the sample. The comparative analysis of materials with different compositions is based on simulation results that are well concordant with the results of the laboratory experiments.

• Journal of Industrial and Engineering Chemistry
• /
• v.68
• /
• pp.246-256
• /
• 2018

Graphene oxide (GO) reinforced Polyvinyl chloride (PVC)-Waterborne Castor Alkyd (WCA) nanocomposites (PVC/WCA/GO) films were processed through solution blending technique. TGA showed that the thermal stability of PVC/WCA/GO-0.5 films was better than that of PVC/WCA blend film. With incorporation of 0.5 wt.% GO, the tensile strength and elastic modulus of the blend nanocomposite have significantly improved by about 260% and 185%, respectively, compared with neat polymer. The physicomechanical properties of these films suggest that the PVC/WCA/GO nanocomposite films may have a potential scope for their application in packaging industries. The results are supported by characterizations like FTIR, XRD, TEM and FESEM.