• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10b
• /
• pp.550-553
• /
• 1993

Methods of Alternating Noise Canceling were previously developed for the optical instrumentation;one using a dual photo sensor and another using a single photo sensor that could cancel normal mode noise on a transmission line, even if the noise was of equal status noise. But the methods could not remove noise on sensor line. This paper discusses a new method of using a photo sensor with a resistance sensordummy, effectively canceling equal status normal mode noise not only on a sensor line but also on a transmission line of an optical instrumentation. The accuracy of this method has been verified by experiments using sinusoidal wave as an equal status noise on a sensor line and/or rectangular wave as an equal status wide band noise on a transmission line respectively.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.3
• /
• pp.28-35
• /
• 2013

Micro electrical discharge machining (EDM) as a non-contact machining process is very effective for micromachining with a thin electrode because of its low machining reaction force. The micro-electrode machining device has the advantage of maintaining high precision through the whole processes and uses a feeding wire in the thin electrode tool manufacturing process. This study describes the design and evaluation of a micro-electrode machining device using optical photo-interrupter. The electrode was fabricated by reverse electrical discharge machining. The performance of designed system was evaluated to measure tension force according to feed speed of wire. This system for micro electrode fabrication proves the feasibility in the micro-EDM process of the micro holes and parts for industrial applications.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1695-1700
• /
• 2005

In this paper, we propose an optimal thresholding method for the voxel coloring in the reconstruction of a 3D shape. Our purposed method is a new approach to resolve the trade-off error of the threshold value on determining the photo-consistency in the conventional method. Optimal thresholding value is decided to compare the surface voxel of photo-consistency with inside voxel on the optic ray of the center camera. As iterating the process of the voxels, the threshold value is approached to the optimal value for the individual surface voxel. And also, graph cut method is reduced to the surface noise on eliminating neighboring voxel. To verify the proposed algorithm, we simulated in the virtual and real environment. It is advantaged to speed up and accuracy of a 3D face reconstruction by applying the methods of optimal threshold and graph cut as compare with conventional algorithms.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1171-1174
• /
• 2005

This thesis provides a new digital convergence method and apparatus which uses area photo sensor and new analog to digital algorithmic to identify the correct digital pattern position factor of the projection system. This method and apparatus can be applied to the convergence correction in a TV receiver with a display that comprises a display screen with photo sensors positioned adjacent to screen edges. It also can be applied to the manufacture process detection of the projection system to adjust the associative convergence parameter. In this paper, demonstrate how this convergence detecting algorithmic was implemented with four area photo sensors of special designed pattern to the rear projection CRT TV.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.5
• /
• pp.198-204
• /
• 2007

This study was carried out to develope a flow control system using to supply PR(photo-resist) in the semi-conductor manufacturing process. The features of this system are to be able to measure the high viscosity and micro-flow. To meet above study object some ideas was induced to design a new concept valve with new material, multi-cross wheel, and new sealing method etc.. As the evaluations on the developed micro-flowmeter it was enough satisfied to use at the IT industries such as photo-resist process.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.354-359
• /
• 1994

On-line process control equipment for CO $_{2}$ laser cutting is unavailable for industrial application. The major part of the industrial cutting machines are regulated off-line by highly educated engineers. The quality inspection of the sample is visual and referred to different quality scales. Due to lack of automation potential laser users hesitate to implement the cutting method. The first step toward an automation of the process is development of a process monitoring system and the research is concentrated on the area of on-line quality detection during CO $_{2}$ laser cutting. The method bases on the detection of the emitted light from the cut front by photo diode. the signal from photo diode has been undertaken from Fourier analysis and statistical analysis. As a result, it is possible to estimate striation pattern according to beam travel speed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.109-109
• /
• 2006

Screen printing (SP) metal contact is typically applied to the solar cells for mass production. However, SP metal contact has low aspect ratio, low accuracy, hard control of the substrate penetration and unclean process. On the other hand, photo lithograpy (PL) metal contact can reduce defects by metal contact. In this investigation, PL metal contact was obtained the multi-layer structure of Ti/Pd/Ag by e-beam process. We applied SP metal contact and PL metal contact to single crystalline silicon solar cells, and demonstrated the difference of conversion efficiency. Because PL metal contact silicon solar cell has Jsc (short circuit current density) better than silicon solar cell applied SP metal contact.

• Current Photovoltaic Research
• /
• v.8 no.2
• /
• pp.60-65
• /
• 2020

In perovskite solar cells with planar heterojunction configuration, selection of proper charge-transporting layers is very important to achieve stable and efficient device. Here, we developed solution processible Cu doped NiO_x (Cu:NiO_x) thin film as a hole-transporting layer (HTL) in p-i-n structured methylammonium lead trihalide (MAPbI₃) perovskite solar cell. The transmittance and thickness of NiO_x HTL is optimized by control the spin-coating rate and Cu is additionally doped to improve the surface morphology of undoped NiO_x thin film and hole-extraction properties. Consequently, a perovskite solar cell containing Cu:NiO_x HTL with optimal doping ratio of Cu exhibits a power conversion efficiency of 14.6%.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.12
• /
• pp.30-37
• /
• 1996

On-line process control equipment for CO$_{2}$ laser cutting is not available for industrial applications. The major part of the industrial laser cutting machines are adjusted off-line by highly educated engineers. The quality inspection of the sample is visual and referred to different quality scales. Due to the lack of automation the potential laser users hesitate to implement the cutting method. The first step toward an automation of the process is the development of a process monitoring system and the research is cincentrated on the area of on-line quality monitoring during CO$_{2}$ laser cutting. The method is based on the detection of the emitted light from the cutting front by photo diode. The developed monitoring system consists of the OP Amplifier, A/D convertor, power supply and PC. The signal from the photo diode has been undertaken from Fourier analysis and statistical analysis with real time. The photograph of striation pattern was taken by metallurgical microscope. As a result, it is possible to predict the striation pattern according to the beam traveling speed.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.38 no.4
• /
• pp.305-315
• /
• 2020

The purpose of this study is to compare algorithms of single photo resection, which determines the exterior orientation parameters used in fields such as photogrammetry, computer vision, robotics, etc. To this end, the algorithms were compared by generating experimental data by simulating terrain based on a camera used in aerial and close-range photogrammetry. Through experiments on aerial photographic camera that was taken almost vertically, it was possible to determine the exterior orientation parameters using three ground control points, but the Procrustes algorithm was sensitive to the configuration of the ground control points. Even in experiments with a close-range amateur camera where the attitude angles of the camera change significantly, the algorithm was sensitive to the configuration of the ground control points, and the other algorithms required at least six ground control points. Through experiments with two types of cameras, it was found that cosine lawbased spatial resection shows performance similar to that of a traditional photogrammetry algorithm because the number of iterations is short and no explicit initial values are required.