• Herbal Formula Science
• /
• v.21 no.1
• /
• pp.177-185
• /
• 2013

Objectives : Leejung-tang (Lizhong-tang) has been used for treatment of gastrointestinal disorders in Korea. In this study, we performed quantification analysis of five marker components, liquiritin, ginsenoside Rb1, ginsenoside Rg1, glycyrrhizin, and 6-gingerol in Leejung-tang using a ultra performance liquid chromatography- electrospray ionization-mass spectrometer (UPLC-ESI-MS). In addition, we evaluated antioxidant activity of Leejung- tang. Methods : The column for separation of five constituents used a UPLC BEH C18 ($100{\times}2.1mm$, $1.7{\mu}m$) maintained at $45^{\circ}C$. The mobile phase consisted of two solvent systems, 0.1% (v/v) formic acid in H2O (A) and CH3CN (B) by gradient flow. The flow rate was 0.3 mL/min with detection at mass spectrometer. The antioxidative activities conduct an experiment on 2,2'-azinobis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) and 2,2-diphenyl-2-picrylhydrazyl (DPPH) radical scavenging activities of Leejung-tang. Results : Calibration curves of five marker compounds were acquired with r2 values > 0.99. The amount of the five compounds in Leejung-tang were 0.07 - 0.84 mg/g. The concentration required for 50% reduction (RC50) against ABTS radical was 119.02 ug/mL. In addition, the scavenging against DPPH radical of Leejung-tang was 11.4%, 14.5%, 19.8%, 29.6%, and 49.2% at 25 ug/mL, $50{\mu}g/mL$, $100{\mu}g/mL$, $200{\mu}g/mL$, and $400{\mu}g/mL$, respectively. Conclusions : The established LC-MS/MS method will be helpful to improve quality control of Leejung-tang. In addition, Leejung-tang is a potential antioxidant therapeutic agent.

• Journal of Power System Engineering
• /
• v.20 no.6
• /
• pp.27-33
• /
• 2016

BLDC motors have the strong point of allowing high-efficiency operation, yet with the weak point of requiring position information for operation. Moreover, there have recently been frequent cases where the product differentiation of even a cheap BLDC motor demanded a high level of control performance similar to that of a controller using a high-precision position sensor. This paper proposes low cost position sensor that enables the acquisition of rotor position information based on index and incremental PWM, using a single position sensor instead of an expensive incremental encoder or a cheap 3 phase hall sensor. The characteristic of the proposed encoder is that index information at every $60^{\circ}$ of electrical angle is inscribed on the encoder disk, as well as a multiple number of values representing information about PWM, which is obtained by modulating information about the electrical angle of the rotor that has the resolution of $60^{\circ}$. Such a method has the characteristic of enabling the acquisition of high-precision position information based on the information about a multiple number of PWM waveforms and counter values that have all been inscribed on the encoder disk for each $60^{\circ}$ range. The feasibility of the proposed new encoder was verified by fabricating a prototype encoder generating 240 pulses, followed by confirming its performance using Micom's capture and software counter functions.

• Journal of Korean Society of Water and Wastewater
• /
• v.21 no.6
• /
• pp.679-687
• /
• 2007

Nanoscale zero valent ion (nZVI) technology is emerging as an innovative method to treat contaminated groundwater. The activity of nZVI is very high due to their high specific surface area, and supporting this material can help to preserve its chemical nature by inhibiting oxidation. In this study, nZVI particles were attached to granular ion-exchange resin through borohydride reduction of ferrous ions, and chemical reduction of nitrate by this material was investigated as a potential technology to remove nitrate from groundwater. The pore structure and physical characteristics were measured and the change by the adsorption of nZVI was discussed. Batch tests were conducted to characterize the activity of the supported nZVI and the results indicated that the degradation of nitrate appeared to be a pseudo first-order reaction with the observed reaction rate constant of $0.425h^{-1}$ without pH control. The reduction process continued but at a much lower rate with a rate constant of $0.044h^{-1}$, which is likely limited by mass transfer. To assess the effects of other ions commonly found in groundwater, the same experiments were conducted in simulated groundwater with the same level of nitrate. In simulated groundwater, the rate constant was $0.078h^{-1}$ and it also reduced to $0.0021h^{-1}$ in later phase. The major limitation in application of ZVI for nitrate reduction is ammonium production. By using a support material with ion exchange capacity, the problem of ammonium release can be solved. The ammonium was not detected in the batch test, even when other competitive ions such as calcium and potassium existed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.2
• /
• pp.147-150
• /
• 2020

Relatively pure YBCO was first synthesized by heating a mixture of metal carbonates at temperatures between 1,000 and 1,300 K, resulting in the reaction: 4BaCO₃+Y₂(CO₃)₃+6CuCO₃+(1/2_-x)O₂ → 2YBa₂Cu₃O_7-x+1/3CO₂. Modern syntheses of YBCO use the corresponding oxides and nitrates. The superconducting properties of YBa₂Cu₃O_7-x are sensitive to the value of x, i.e., its oxygen content. Only those materials with 0≤x≤0.65 are superconducting below Tc, and when x ~ 0.07, the material superconducts at the highest temperature, i.e., 95 K, or in the highest magnetic fields, i.e., 120 T and 250 T when B is perpendicular and parallel to the CuO₂ planes, respectively. In addition to being sensitive to the stoichiometry of oxygen, the properties of YBCO are influenced by the crystallization methods applied. YBCO is a crystalline material, and the best superconductive properties are obtained when crystal grain boundaries are aligned by careful control of annealing and quenching temperature rates. However, these alternative methods still require careful sintering to produce a quality product. New possibilities have arisen since the discovery of trifluoroacetic acid, a source of fluorine that prevents the formation of undesired barium carbonate (BaCO₃). This route lowers the temperature necessary to obtain the correct phase at around 700℃. This, together with the lack of dependence on vacuum, makes this method a very promising way to achieve a scalable YBCO bulk.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.8
• /
• pp.843-848
• /
• 2015

The objective of this study is to observe and optimize a typical ocean environment and reduce wave reflections in the wave flume. In order to generate ocean waves in the wave flume, a combination of a horizontal piston type wave generator and wave absorbers was installed in the channel. Two probes for measuring the wave heights, i.e., wave level gauges, were used to record the continuous variation of the wave surface, the phase difference, and the maximum (crest) and minimum (trough) points of the propagating waves. In order to optimize the shape and size of the propagating waves, several absorption methods were proposed. Apart from an active wave absorption method, we used methods that involved vertical porous plates, horizontal punching plates, and sloping-wall-type wave absorbers. To obtain the best propagating waves, a sloping-wall-type wave absorber was chosen and tested in terms of the constitutive filling materials and the location and shape of the plate. This study also focused on the theoretical prediction of the wave surface, separating them into the incident and reflective components. From the results, it is evident that the wave absorber comprising a hard filling material exhibits a better performance than the absorber comprising a soft material, i.e., the wave absorber can be a strong sink to control the energy of the incoming wave. In addition, larger wave absorbers correspond to lower reflectance because a larger volume can reduce the incoming wave energy. Therefore, at constant absorber conditions, the reflectance of the wave increases as the wave period increases. Finally, the reflectance of the wave was controlled to be less than 0.1 in this study so that the wave flume can be used to simulate an offshore environment.

• The Journal of Korean Medicine
• /
• v.25 no.3
• /
• pp.45-54
• /
• 2004

Objectives : This study was aimed to evaluate marker substances in Gami-Honghwa-Tang (KH-19) by high performance liquid chromatography-photodiode array detector (HPLC-DAD). Gami-Honghwa-Tang is composed of nine crude herbs, Rehmanniae Radix Preparata, Angelicae Gigantis Radix, Cnidii Rhizoma, Paeoniae Radix, Corni Fructus, Moutan Cortex Radicis, Lycii Fructus, Carthami Flos and Glycyrrhizae Radix. Methods : The separation was performed on an Aquasil C18 (4.6×250mm) column by gradient elution with 0.05% TFA in H2O - 0.05% TFA in acetonitrile (0 min 100:0, 20 min 90:10, 40 min 70:30, 60 min 50:50, 80 min 0:100, 90 min 100:0) as the mobile phase at a flow-rate of 1.0 ml/min with detection at 190-800nm. Also we examined the contents for bacteria, pesticide residue and harmful heavy metals. Results : HPLC-DAD was employed to determine the quantities and the qualities of several marker substances such as 5­hydroxymethyl-2-furaldehyde (5-HMF), paeonol, loganin, paeoniflorin, glycyrrhizin, and decursin in the KH-19. There were no bacterial contents, pesticide residues, or harmful heavy metals. Conclusions : We suggest these results could be a useful evidence for quality control of KH-19. This method permits fingerprints of selected individual marker substances from herbal prescriptions without derivatization, multiple purification steps, or lengthy separation times.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.60 no.1
• /
• pp.107-113
• /
• 2015

This study was conducted to find out the effective induction method of tetraploid plants to obtain potential data for cultivating superior varieties by colchicine treatment. The seed germination were decreased by the higher concentration of colchicine treatment and longer soaking time. A total of 907 individuals were germinated in 16 treated plots except control (untreated plot) and 28 tetraploids were induced which was about 3.1% of the number of seed germinated. The plant regeneration rate by colchicine treatment on explant of Prunella vulgaris for. albiflora Nakai under in vitro culture was decreased with the higher concentration of colchicine. While a total of 312 individuals were regenerated in all treatments, the explant was soaked in more than 0.05% for over 1 hour, tetraploid could be obtained. In particular, for the soaking treatment in 0.05% for 6 hours and 12 hours, 37 tetraploids were induced, which was about 57.8% of the number of plant regenerated. In accordance with the observation on doubling of DNA contents in leaf in order to identify polyploid, the peak DNA content of G1 phase was 101.3 for diploid and 197.2 for tetraploid. The result confirmed the doubling of DNA content. Furthermore, the number of chloroplasts per guard cell depending on polyploid was around 10 in diploid and 19.3 in tetraploid, which was around 1.9 times as much as diploid.

• Analytical Science and Technology
• /
• v.5 no.3
• /
• pp.327-332
• /
• 1992

Mn-Zn ferrite single crystals show some fluctuations in composition along the direction of growth by the conventional Bridgman method. The single crystal with a uniform composition was obtained by maintaining the liquid composition content. For example, two batches of powder were prepared : one is consisted of 52 mol% of $Fe_2O_3$, 30 mol% of MnO, and 18 mol% Zn(Composition A), and the other 53 mol% of $Fe_2O_3$, 28.5 mol% of MnO, and 18.5 mol% ZnO(Composition B). Crack-free single crystals with the uniform composition B were grown in a size of 60mm diameter, 300mm long by melting the pellets of composition A and followed by supplying the composition B as tablets. Initial permeabilities were obtained above 600 at 5 MHz in the region of 30~270 mm along the direction of growth.

• Journal of Microbiology and Biotechnology
• /
• v.14 no.4
• /
• pp.715-721
• /
• 2004

Many food protein hydrolysates have been shown to have antioxidant activities, and recent research focuses on low molecular peptides produced during hydrolysis of food protein. Korean rice wine contains about 60-70% of protein at dry base and originates from raw materials. It has been suggested that the protein is transformed into low molecular weight peptides, and have antioxidant activity during fermentation. The objectives of this study were to evaluate the antioxidant activity of the pre-purified and purified peptides found in Korean rice wine and to identify the responsible peptides. The wine extract of Samhaeju, a traditional Korean rice wine made by low temperature fermentation, was evaporated at $35^{\circ}C$. The two methods employed in the evaluation of antioxidant activity were the DPPH radical scavenging method and the beta-carotene bleaching test. The pre-purified samples showed 808 AAC (Antioxidant Activity Coefficient) and 56.5% AOA (Antioxidant Activity), which were higher than $\alpha$-tocopherol (572 AAC and 78% AOA). The rice wine extract was separated by reversed-phase HPLC. The protective effect of the four most antioxidant active fractions were tested for t-butyl hydroperoxide induced oxidation of healthy human erythrocytes and the byproduct was determined by malondialdehyde formation. Fraction No.5 showed 35% lower MDA concentration as compared to the control. The peptides were further purified using consecutive chromatographic methods and 4 antioxidant peptides were isolated. The amino acid sequences of the peptides were identified as Ile-His-His, Val- Val-His(Asn), Leu-Val-Pro, and Leu(Val)-Lys-Arg-Pro. The AAC value of the synthetic form of the identified peptides was the highest for Ile-His-His.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.6
• /
• pp.566-572
• /
• 2004

It is necessary to measure the direct current with a non-contact methodology for the liquid or gas phase, as welt as the conducting metals. This paper described a theoretical consideration and experimental verification for a non-contact quantitative direct current measurement system using the Faraday effect and magnetic flux leakage. The leakage of magnetic flux occurs around a gap when a ferromagnetic core including the discontinuous gap is magnetized. Two large anisotropic domains in a magneto-optical film are occurred by the vertical component of leaked magnetic flux and the domain walls are paralleled to the center of the gap. Here, the symmetrical arrangement of domains are deflected when a vertical magnetic field is applied to the magneto-optical film. The domain wall of the magneto-optical film are relocated when a measuring current passes through the ferromagnetic core. Therefore, a direct current passing through the core can be determined quantitatively by the measurement of moving distance of the domain wall.