• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.19 no.1 s.71
• /
• pp.93-103
• /
• 2006

It is absolutely essential that safety assessment of the containment buildings during service life because containment buildings are last barrier to protect radioactive substance due to the accidents. Therefore, this study describes an enhanced degenerated shell finite element(FE) which has been developed for nonlinear FE analysis of reinforced concrete(RC) containment buildings with elasto-plastic material model. For the purpose of the material nonlinear analysis, Drucker-Prager failure criteria is adapted in compression region and material parameters which determine the shape of the failure envelop are derived from biaxial stress tests. Reissner-Mindlin(RM) assumptions are adopted to develop the degenerated shell FE so that transverse shear deformation effects is considered. However, it is found that there are serious defects such as locking phenomena in RM degenerated shell FE since the stiffness matrix has been overestimated in some situations. Therefore, shell formulation is provided in this paper with emphasis on the terms related to the stiffness matrix based on assumed strain method. Finally, the performance of the present shell element to analysis RC containment buildings is tested and demonstrated with several numerical examples. From the numerical tests, the present results show a good agreement with experimental data or other numerical results.

• Korean journal of applied entomology
• /
• v.49 no.4
• /
• pp.393-400
• /
• 2010

The parasitism, development time, hatchability, and progeny production of Trichogramma chilonis(TC) females developed in eggs of Helicoverpa assulta (HAs), Cadra cautella (CC), and Helicoverpa armigera (HAr), respectively, were compared with those developed in reciprocal eggs at constant temperatures of $25{\pm}2^{\circ}C$ and relative humidity of 50~70% under 16L-8D. Developmental performances of TC reared in each of the three hosts on the following hosts(host tested) appeared differently, and were affected most by the size of the proceeding hosts and test host. Among the parameters parasitism and progeny production were affected more than others. Parasitism was significantly different between the treatments, lowest in CC-HAr($10.1{\pm}2.05%$) and highest in HAr-HAs($47.0{\pm}2.09%$), and the hatchability showed similar pattern. Development time as well was shortest in the CC-HAr where previous host is smallest and test host is biggest. The highest number of progeny production of TC was observed in HAr-HAs($93.9{\pm}6.87$ wasps), and the lowest was CC-HAs($18.4{\pm}6.36$ wasps).

• Korean Journal of Child Education & Care
• /
• v.17 no.2
• /
• pp.181-203
• /
• 2017

The purpose of this research is to reveal the difference of teacher-child interaction in relation to professionalism awareness and sensitivity level of early childhood teachers. To this end, we used professionalism awareness, sensitivity, teacher-child interaction as parameters for 226 early childhood teachers in Jeonbuk province. Here are the results : First, we investigated the difference of professionalism awareness, sensitivity, teacher-child interaction in relation to the background of early childhood teachers, and it differs by the age, career, educational level of the teachers. Second, we made group comparison to see the difference of teacher-child interaction depending on professionalism awareness level of teachers, and teachers with high professionalism awareness showed meaningfully higher emotional, verbal, behavioral interaction level than lower group. Third, we made group comparison to see the difference of teacher-child interaction depending on sensitivity level, and teachers of high sensitivity shows meaningfully higher emotional, verbal interaction than lower group. This result could be potential data to ameliorate the quality of teacher-child interaction, and it implies that the improvement of professionalism and sensitivity level could contribute to professional performance capability of teachers.

• Spatial Information Research
• /
• v.12 no.2
• /
• pp.181-191
• /
• 2004

Nowadays, GPS-photogrammetry can be applied to the basemap production, a land register and NGIS. And from now on, as the increase of GPS receiver rate, the study on the interpolation methods considering the exact movement of an aircraft at photoflight and the study on the supplement of GPS defect by INS are required continuously. GPS-Photogrammetry, which are based on the direct measurement of the projection centers and attitude at the moment of camera exposure time through loading the GPS receiver in aircraft. This photogrammetric methods can of for us to acquire the exterior orientation parameters with only minimum ground control points, even the ground control process could be completely skipped. Consequently, we can drastically reduce the time and cost far the mapping process. In this thesis, two test flights were conducted in area to evaluate the performance of accuracy and efficiency through the analysis of results between the two photogrammetric methods, that is, traditional photograrammetry, GPS-Photogrammetry. Test results shows that a large variety of advantages of GPS-Photogrammetry against traditional photogrammetry is to be verified. Especially, the number of ground control points for the exterior orientation could be saved more than 70～80%, and the cost far map production 30～50%, respectively. In addition, it was convinced that the large reduction of control points has not any effect on the block accuracy.

• Proceedings of KOSOMES biannual meeting
• /
• 2007.05a
• /
• pp.91-96
• /
• 2007

Lab scale experimental study was carried out for SBR process, to investigate the effects of influent ship sewage organic compound removal and Bacillus sp. state on design parameters. This process was able to remove nitrogen and phosphorus as well as organic matter efficiently. More than 95% of chemical oxygen demand(COD) were removed. In addition, about 97% of total nitrogen (T-N) was reduced. The total phosphorus(T-P) reduction averaged 93%. The performance load of SBR process was shown to be $0.095kg{\cdot}TOC/m^3{\cdot}day$. The pH was decreased from 8.1 to 7.0 within 30 min and increased to 7.3 at the end of anoxic stage, and these phenomena were explained. The sludge produced in the SBR process is characterized by low generation rate (about $0.36kg{\cdot}MLSS/kg{\cdot}TOC$) and excellent settleability. The number of Bacillus sp. in the SBR was 24.2%, indicating that Bacillus sp. was a predominant species in the reactor.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.9
• /
• pp.768-773
• /
• 2016

Engine valve seat and face, which are the important factors affecting engine performance, are required to have wear, heat and corrosion resistance. In order to produce surface layer with these characteristics, PTA(plasma transferred arc) surfacing procedure is generally employed, but problems, such as large HAZ and high dilution etc., frequently occurr. Laser cladding, which overcomes the drawbacks of conventional technologies, can be employed to create a superior clad layer with low dilution, small heat affected zone, and minimal distortion. However, in case cladding is to be applied to a large area, it is necessary to overlap 1 pass clad layer because of limited clad layer width. Two criteria for the overlapping ratio-beam size and clad layer width-have been considered thus far. Upon inspection of multi pass clads, produced by different overlapping criteria, it was observed that the greater the increase in overlapping ratio, the greater was the decrease in clad layer width and increase in clad layer height regardless of the criterion used. However, a multi pass clad overlapped by the beam size criterion demonstrated a higher hardness value than a clad overlapped by the clad layer width owing to decreasing dilution of the substrate. In conclusion, the beam size was defined as the criterion for the overlapping, because the clad layer width increased or decreased depending upon process parameters.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.9
• /
• pp.799-804
• /
• 2016

Broadband powerline communication (BPLC) uses distribution lines as a medium for achieving effective bidirectional data communication along with electric current flow. As the material characteristics of power lines are not good at the communication channel, the development of power line communication (PLC) systems for internet, voice, and data services requires measurement-based models of the transfer characteristics of the network suitable for performance analysis by simulation. In this paper, an analytic model describing a complex transfer function is presented to obtain the attenuation and path parameters for a multipath power line model. The calculated results demonstrated frequency-selective fading in multipath channels and signal attenuation with frequency, and were in good agreement with the experimental results. Inductive coupling units are used as couplers for coupling the signal to the power line to avoid physical connections to the distribution line. The inductance of the ferrite core, which depends on the frequency, determines the cut-off frequency of the inductive coupler. Coupling loss can be minimized by increasing the number of windings around the coupler. Coupling efficiency was improved by more than 6 dB with three windings compared to the results obtained with one winding.

• Journal of the Society of Naval Architects of Korea
• /
• v.28 no.2
• /
• pp.1-11
• /
• 1991

A hull form for an Aframax tanker whore form parameters cover the values of $C_B{\simeq}0.8,\;L/B{\simeq}5.5\;and\;B/d{\simeq}3.5$ has been developed by applying a composite stern frameline concept and its excellent performance has been evaluated through a series of model tests at the Korea Research Institute of Ships and Ocean Engineering. The tests showed that this concept was very much promising in the cases of wide breadth and shallow draught vessels and suitably applicable to the stern frameline shape. For the comparison, a hull form developed by Japanese 'H' yard has been selected and the performances of two hull forms were evaluated by model tests and theoretical calculations. The comparison shows that Daewoo hull form requires less effective power by 10% and less delevered power by 5-6% at both full load and ballast conditions. In addition, it is suggested that Hushes method can give better correlationthan Froude method because the full scale resistance extrapolated by Froude method would be very much optimistic in case of the hull form with very low value of form factor.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.14 no.2
• /
• pp.96-108
• /
• 2011

Going abreast of high public concerns on the environment, the need of environmental modeling has been increased to assess the impact of space exploitation of environment. GIS offers potential solutions to the many problems encountered during water-quality modeling. But there are also many problems associated with the modeling. The preparation of necessary parameters for the modeling can be complicated. Also, the results from one model can be different from each other even the same area is analyzed. This paper aims to develop the data processing system to couple the Qual2E and HyGIS in which Qual2E input and output data files can be created, modified and processed using HyGIS and assess the performance of the system. A structural analysis and standardization of modeling are conducted to identify data flow and processing of Qual2E. Algorithms of the defined processors are designed and developed as component modules. The data model of HyGIS-Qual2E is designed, and GUI(Graphical User Interface) is developed using Visual Basic 6.0 and GDK.

• Korean Journal of Optics and Photonics
• /
• v.4 no.1
• /
• pp.15-21
• /
• 1993

This paper describes the design and development of a KrF excimer laser stepper and discusses the detailed system parameters and characterization data obtained from the performance test. We have developed a deep UV step-and-repeat system, operating at 248 nm, by retrofitting a commercial modules such as KrF excimer laser, precision wafer stage and fused silica illumination and 5X projection optics of numerical aperture 0.42. What we have developed, to the basic structure, are wafer alignment optics, reticle alignment system, autofocusing/leveling mechanisms and environment chamber. Finally, all these subsystem were integrated under the control of microprocessor-based controllers and computer. The wafer alignment system comprises the OFF-AXIS and the TTL alignment. The OFF-AXIS alignment system was realized with two kinds of optics. One is the magnification system with the image processing technique and the other is He-Ne laser diffraction type system using the alignment grating on the wafer. 'The TTL alignment system employs a dual beam inteferometric method, which takes advantages of higher diffraction efficiency compared with other TTL type alignment systems. As the results, alignment accuracy for OFF-AXIS and TTL alignment system were obtained within 0.1 $\mu\textrm{m}$/ 3 $\sigma$ for the various substrate on the wafers. The wafer focusing and leveling system is modified version of the conventional systems using position sensitive detectors (PSD). This type of detection method showed focusing and leveling accuracies of about $\pm$ 0.1 $\mu\textrm{m}$ and $\pm$ 0.5 arcsec, respectively. From the CD measurement, we obtained 0.4 $\mu\textrm{m}$ resolution features over the full field with routine use, and 0.3 $\mu\textrm{m}$ resolution was attainable under more strict conditions.