• 한국분무공학회지
• /
• 제29권1호
• /
• pp.32-37
• /
• 2024

Macroscopic visualization of non-evaporating sprays was experimentally conducted to investigate spray tip penetration and spray angle under low-density conditions, corresponding to an early injection strategy. Furthermore, injectors with varying injection angles (146° and 70°) and numbers of holes (8 and 14) were employed to examine the impact of injector configuration. Compared to the baseline injector, 8H146, which has 8 holes and a 146° injection angle, the spray tip penetration of the 8H70 injector was found to be longer. This can be attributed to higher momentum due to a smooth flow field between the sac volume and the nozzle inlet, which is located closer to the injector tip centerline. The increase in velocity led to intense turbulence generation, resulting in a wider spray angle. Conversely, the spray tip penetration of the 14H70 injector was shorter than that of the 8H70 injector. The competition between increased velocity and decreased nozzle diameter influenced the spray tip penetration for the 14H70 injector; the increase in momentum, previously observed for the 8H70 injector, contributed to an increase in spray tip penetration, but a decrease in nozzle diameter could lead to a reduction in spray tip penetration. The spray angle for the 14H70 injector was similar to that of the 8H146 injector. Moreover, injection rate measurements revealed that the slope for a narrow injection angle (70°) was steeper than that for a wider injection angle during the injection event.

• 국제강구조저널
• /
• 제18권5호
• /
• pp.1589-1597
• /
• 2018

Fatigue tests and numerical analysis were carried out to evaluate the fatigue performance at the U-rib to deck welded joint in steel box girder. Twenty specimens were tested corresponding to different penetration rates (80 and 100%) under fatigue bending load, and the fatigue strength was investigated based on hot spot stress (HSS) method. The detailed stress distribution at U-rib to deck welded joint was analyzed by the finite element method, as well as the stress intensity factor of weld root. The test results show that the specimens with fully penetration rate have longer crack propagation life due to the welding geometry, resulting in higher fatigue failure strength. The classification of FAT-90 is reasonable for evaluating fatigue strength by HSS method. The penetration rate has effect on crack propagation angle near the surface, and the 1-mm stress below weld toe and root approves to be more suitable for fatigue stress assessment, because of its high sensitivity to weld geometry than HSS.

• Clinical and Experimental Reproductive Medicine
• /
• 제30권1호
• /
• pp.105-109
• /
• 2003

Objective s: To assess the fertilizing capacity using sperm penetration assay (SPA) to predict the outcome of the in vitro fertilization-embryo transfer (IVF-ET) outcome. Materials and Methods: Semen samples were provided by 129 patients undergoing IVF. We attempted to correlate the extent of sperm penetration under enhanced SPA protocol with the results of fertilization, cleavage, preimplantation embryo development, and pregnancy. Results: Univariate analysis demonstrated a statistically significant correlation between fertilizing capacity and motility, kinetics, fertilization, cleavage and embryo development, and pregnancy rate. By logistic regression analysis, fertilizing capacity was found to be the only variable that was statistically significant with respect to pregnancy rate. Fertilizing capacity, cleavage rate and pregnant rate were significantly higher in pregnant group. However, the fertilization rates was comparable with both group. Conclusions: Lower fertilizing capacity could denote a poorer prognosis for establishing a pregnancy, even after satisfactory fertilization rate is achieved.

• 한국레이저가공학회지
• /
• 제16권2호
• /
• pp.1-6
• /
• 2013

Picosecond lasers are a very effective tool for micromachining metals, especially when high accuracy, high surface roughness and no heat affected zone are required. However, low productivity has been a limit to broadening the spectrum of their industrial applications. Recently it was reported that in the micromachining of copper with a 1064nm picosecond laser, there exist the optimal pulse energy and repetition rate to achieve the maximum volume ablation rate. In this paper, we used a 515nm picosecond laser, which is more efficient for micromachining copper in terms of laser energy absorption, to obtain its optimal pulse energy and repetition rate. Theoretical analysis based on the experimental data on copper ablation showed that using a 515nm picosecond laser instead of a 1064nm picosecond laser is more favorable in that the calculated threshold fluence is 75% lower and optical penetration depth is 50% deeper.

• 수산해양기술연구
• /
• 제52권1호
• /
• pp.65-71
• /
• 2016

Injection rate, injection quantity and injection timing of fuel are controlled precisely by electric control in CRDI system. Particularly, injection rate being influenced with injection pressure affects to spray characteristics and fuel-air ratio, so it is a very important factor in diesel combustion. In this study, injection rates in accordance with injection pressure at a constant ambient pressure were measured with Zeuch's method. Under the same condition, non-evaporating spray images were taken with a high speed camera and analyzed carefully with Adobe Photoshop CS3. Macroscopic spray characteristics and breakup processes in the spray could be found from the examined and analyzed data. Injection start time and injection period were practically affected with injection pressure. Also, initial injection rate, spray penetration, spray angle and breakup of high density droplets region in the spray were affected with injection pressure. The results and techniques of spray visualization and injection rate measurement in this study would be practically effective to study a high pressure diesel spray for common rail direct injection system.

• 천문학회보
• /
• 제44권1호
• /
• pp.48.2-48.2
• /
• 2019

Tidal disruption events (TDEs) provide evidence for quiescent supermassive black holes (SMBHs) in the centers of inactive galaxies. TDEs occur when a star on a parabolic orbit approaches close enough to a SMBH to be disrupted by the tidal force of the SMBH. The subsequent super-Eddington accretion of stellar debris falling back to the SMBH produces a characteristic flare lasting several months. It is theoretically expected that the bolometric light curve decays with time as proportional to $t^{-5/3}$. However, some of the observed X-ray light curves deviate from the $t^{-5/3}$ decay rate, while some of them are overall in good agreement with the $t^{-5/3}$ law. Therefore, it is required to construct the theoretical model for explaining these light curve variations consistently. In this paper, we revisit the mass fallback rates semi-analytically by taking account of the stellar internal structure, orbital eccentricity and penetration factor. We find that the mass fallback rate is shallower than the standard $t^{-5/3}$ decay rate independently of the polytropic index, and the orbital eccentricity only changes the magnitude of the mass fallback rate. Furthermore, the penetration factor significantly can modify the magnitude and variation of mass fallback rate. We confirm these results by performing the computational hydrodynamic simulations. We also discuss the relevance of our model by comparing these results with the observed light curves.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2021년도 춘계학술대회
• /
• pp.204-206
• /
• 2021

실시간 시추매개변수 예측은 시추효율의 극대화 관점에서 상당히 중요한 연구이다. 시추 극대화 방법 중 시추속도를 향상시키는 방법이 일반적인데 이는 굴진율, 시추스트링 회전속도, 비트 하중, 시추이수 유량과 연관관계를 지니고 있다. 본 연구는 실시간 시추매개변수 중 하나인 굴진율을 순환신경망기반 딥러닝 모델을 이용하여 예측하는 방법을 제안하였으며 기존의 물리적 기반의 굴진율 모델과 딥러닝 모델을 이용한 예측 모델을 비교해 보고자 한다.

• 대한약학회:학술대회논문집
• /
• 대한약학회 2003년도 Proceedings of the Convention of the Pharmaceutical Society of Korea Vol.2-2
• /
• pp.234.1-234.1
• /
• 2003

The effects of vehicles and penetration enhancers on the in vitro permeation of ketorolac tromethamine (KT) across excised hairless mouse skins were investigated. Among pure vehicles examined, propylene glycol monolaurate (PGML) showed the highest permeation flux, which was 94.3${\pm}$17.3 mg/cm$^2$/hr. Even though propylene glycol monocaprylate (PGMC) alone did not show high permeation rate, the skin permeability of DT was markedly increased by the addition of diethylene glycol monoethyl ether (DGME); the enhancement factors were 19.0 and 17.1 at 20 and 40% of DGME, respectively. (omitted)

• Journal of Pharmaceutical Investigation
• /
• 제31권4호
• /
• pp.217-224
• /
• 2001

To develop a novel transdermal delivery system of loxoprofen (LP), a potent antiinflammatory and analgesic agent, the effects of various vehicles and penetration enhancers on the skin permeation of LP from solution formulations were investigated. The permeation rate of LP through excised guinea pig skin was measured using a side-by-side permeation system at $32^{\circ}C$. The solubilities of LP in various vehicles were determined by the equilibrium solubility method, and partition coefficients $(P_c)$ were determined. The solubility of LP increased in the rank order of water & isopropyl myristate (IPM) & glyceryl dicaprylate/dicaprate & propylene glycol dicaprylate/caprate & propylene glycol laurate (PGL) & polyethylene glycol 400 & diethylene glycol monoethyl ether (DGME) & ethanol. n-Octanol-water $P_c$ value was 15.5. Among pure vehicles tested, IPM and PGL showed highest fluxes of $89.9{\pm}5.0$ and $45.4{\pm}0.3\;{\mu}g/cm^2/hr$ from saturated solutions, respectively. However, it was not possible to demonstrate any correlation between the solubility of LP and its permeation rate, indicating the change in the barrier property of the skin and/or carrier mechanisms by vehicles tested. The addition of DGME to IPM or PGL markedly increased the solubility of LP, but the permeation rate did not decrease when the concentration of DGME in the cosolvent was increased upto 40%. The addition of linoleic acid (3%) in the cosolvent slightly increased the permeation rate, but others such as lauroyl sarcosine, fatty alcohols and fatty acids tested did not show enhancing effect. In conclusion, the DGME-IPM or DGME-PGL cosolvent system proved to be a good vehicle to enhance the skin permeation of LP.

• 한국레이저가공학회지
• /
• 제1권1호
• /
• pp.30-38
• /
• 1998

This study includes the efface of shielding gas types on $CO_2$ laser weldability of low carbon automotive galvanized steel. The types of shielding gas evaluated are He, $CO_2$, Ar, $N_2$, 50%Ar＋50%$N_2$. The weld penetration, strength, formability(Erichsen test) of Laser weld are found to be strongly dependent upon the types of shielding gas used. Further, the maximum travel speed and flow rate to form a keyhole weld is also dependent upon types of shielding gas. The ability of shielding gas in removing plasma plume and thus increasing weld penetration is believed to be closely related with ionization/dissociation potential, which determine the period of plasma formation and disappearance. Further, thermal conductivity and reactivity of gas with molten pool also give strong effect on penetration and porosity formation which in turn affect on the formability and strength.