• Journal of Korean Society of Forest Science
• /
• v.13 no.1
• /
• pp.67-78
• /
• 1971

The measures of contour-terracing with sod has been executed as a major measures for hillside erosion control works for a long time in Korea. It is, however, recognized that pair terracings make a new slope-face having the more steeper degree of slope between the upper and the lower terraces on hillsides and it also does not contribute for establishing the natural vegetation-cover by penetration of pioneer seeds on the slope faces or cut-faces of hillsides. The study was therefore conducted in connection with the above problems on the cut-face having slope of $40^{\circ}$ and 1.6 meter in slope length with clay soils. Plot allocation for the experiment consists of 3 kinds of 3 replica plots having each $1.6m^2$ of slope area, i. e., the control plot with direct seeding on slopes only ($T_1$), the covering plot with the straw-mats after seeding on slopes ($T_2$) and the seeding plot after covering with the straw-mats. ($T_3$). The main results obtained may be summarized as follows : 1. Effects of the straw-mat mulchings on surface soil loss control:-The total amount of soil losses from each treatments are measured as 4,651 gr from $T_1$, 163 gr. from $T_2$ and 2,891 gr. from $T_3$ treatment respectively. (Refer to table No. 2, 3 and 4). In short, it is recognized that effect of $T_2$ treatment is compared as 28.5 times than that of $T_1$ treatment and 17.7 times than that of $T_3$ treatment respectively. Effect of $T_3$ treatment compared with $T_1$ treatment is also such recognizable as 1.6 times in control of surface soil losses on a slope face. 2. Effect of the straw-mat mulchings on soil moisture content on slopes; -Average per cent of surface soil moisture content by treatments show as 21.60 at the $T_1$, 23.04 at the $T_2$ and 22.21 at the $T_3$ treatment respectively and that of subsurface soil moisture content by treatment show as 23.81 at the $T_1$, 26.16 at the $T_2$ and 24.81 at the $T_3$ treatment respectively. The variance of soil moisture content by treatments was highly significant (Refer table No. 7, 8 and 9). 3. Effect of the straw-mat mulchings on vegetation establishment;-Average numbers of germination by treatments are counted as 237 Nos. at the $T_1$, 246 Nos. at the $T_2$ and 262 Nos. at the $T_3$ treatment plots and the vegetation coverage on ground was almost same as about 90% of covers in all treatments. This effect is more or less lower than that of surface soil erosion control. 4. Regarding the effect on surface soil erosion control, the straw-mat mulchings would be effective as a new measures for control of soil erosion on erosion susceptible lands such slope-faced bare-lands as cut-fill faces, mass-movement faces and bare hillsides.

• The Journal of Korean Society for Radiation Therapy
• /
• v.25 no.1
• /
• pp.1-8
• /
• 2013

Purpose: A selection of proper energy in treatment planning is very important because of having different dose distribution in body as photon energy. In generally, the low energy photon has been used in intensity-modulated radiation therapy (IMRT) for head and neck (H&N) cancer. The aim of this study was to evaluate the effect of partially used high energy photon at posterior oblique fields on IMRT plan for H&N cancer. Materials and Methods: The study was carried out on 10 patients (nasopharyngeal cancer 5, tonsilar cancer 5) treated with IMRT in Seoul National University Bundang Hospital. CT images were acquired 3 mm of thickness in the same condition and the treatment plan was performed by Eclipse (Ver.7.1, Varian, Palo Alto, USA). Two plans were generated under same planing objectives, dose volume constraints, and eight fields setting: (1) The low energy plan (LEP) created using 6 MV beam alone, (2) the partially used high energy plan (PHEP) created partially using 15 MV beam at two posterior oblique fields with deeper penetration depths, while 6 MV beam was used at the rest of fields. The plans for LEP and PHEP were compared in terms of coverage, conformity index (CI) and homogeneity index (HI) for planning target volume (PTV). For organs at risk (OARs), $D_{mean}$ and $D_{50%}$ were analyzed on both parotid glands and $D_{max}$, $D_{1%}$ for spinal cord were analyzed. Integral dose (ID) and total monitor unit (MU) were compared as addition parameters. For the comparing dose to normal tissue of posterior neck, the posterior-normal tissue volume (P-NTV) was set on the patients respectively. The $D_{mean}$, $V_{20Gy}$ and $V_{25Gy}$ for P-NTV were evaluated by using dose volume histogram (DVH). Results: The dose distributions were similar with regard to coverage, CI and HI for PTV between the LEP and PHEP. No evident difference was observed in the spinal cord. However, the $D_{mean}$, $D_{50%}$ for both parotid gland were slightly reduced by 0.6%, 0.7% in PHEP. The ID was reduced by 1.1% in PHEP, and total MU for PHEP was 1.8% lower than that for LEP. In the P-NTV, the $D_{mean}$, $V_{20Gy}$ and $V_{25Gy}$ of the PHEP were 1.6%, 1.8% and 2.9% lower than those of LEP. Conclusion: Dose to some OARs and a normal tissue, total monitor unit were reduced in IMRT plan with partially used high energy photon. Although these reduction are unclear how have a clinical benefit to patient, application of the partially used high energy photon could improve the overall plan quality of IMRT for head and neck cancer.

• Korean journal of applied entomology
• /
• v.9 no.2
• /
• pp.57-74
• /
• 1970

These experiments were conducted to investigate the :actors influencing the systemic action of Dimethoate (O,O-dimethyl-S-(N-methylcarhamoylmethyl) photphorodithioate) to rice seeds and the phytotoxic effects on the seed germination. Dimethoate $(Roxion^{(R)})$ $40\%$ emulsion was used. The varieties tested were Jinheung. Nongkwang,Suwon #82, Norm #6, Paltal, Shirogane, Suseong, Pungkwang, Shin #2, Fujisaka #5, Kwanok, and Jaekeun. The permeated Dimethoate was extracted from the treated seeds by chloroform and quantities were determined by Spectrophotometer. The phytotoxicity was evaluated from the effects on the germination of the treated seeds which were kept in an incubator. The oxygen consumption was measured by Warburg Manometer at $30^{\circ}C$ for 60 minutes. Indices of KOH disintegration of seeds and chemical composition of the seeds were also determined. The results obtained were as followings; 1) The amount of permeated Dimethoate in the seeds showed remarkable differences with varieties. The amount of Dimethoate per 100 grains was greater as in the ascending order of Suseong, Kwanok, Nongkwang, Jinheung, Paltal, Fujisaka #5, Suwon #82, Norm #6, Shirogane, Shin #2, Pungkwang and Jaekeun. 2) It was observed that the total amount of Dimethoate in the seeds(mg./100 grains) were greater among the varieties with large grain than those with small grains, while reverse cases were true in the amount of Dimethoate in a gramme of seeds, probably because of the greater surface areas In a small grains for a gramme weight. 3) There was no significant correlation between the permeated amount of Dimethoate and amount of absorbed water by the seeds when the seeds were treated with $0.1\%$ Dimethoate for 24 and 48 hours. 4) The permeability of Dimethoate to seeds significantly increased in the prolonged soaking periods, higher concentration, and higher temperature. 5) When the seeds were treated with $0.1\%$ Dimethoate for 24 and 48 hours at $15^{\circ},\;20^{\circ},\; 20^{\circ},\; and \;30^{\circ}C$, the permeated amount of Dimethoate were increased at higher temperature. It seems to be that the more active penetration of Dimethoate was involved at the higher temperature. 6) The phytotoxic effects of Dinethoate on the seed germination varied with the varieties. An descending order of varietal tolerance of seeds was as followings: Jinheung, Fujisaka #5, Suwon #82, Paltal, Nongkwang, Jaekeun, Shin #2, Kwanok, Shirogane, Pungkwang, Suseong, and Norm #6. 7) There was a positive correlation between the amount of Dimethoate permeated into the seeds (mg./gram. of seeds) and phytotoxicity of seeds. 8) The Phytotoxic effects of Dimethoate showed close correlation with the degree of KOH disintegration of seeds, average germination periods, and oxygen respiration of seeds. 9) It was observed that higher protein contents of the seeds decreased the phytotoxic effects of Dimethoate. 10) Relatively high negative correlation between the degree of KOH disintegration of seeds and crude protein content of the seeds was observed. 11) The average germination period was delayed for about 2 days when the seeds were treated with $0.2\%$ Dimethoate for 24 hours at $30^{\circ}C$. 12) The oxygen consumption of the seeds treated with $0.2\%$ Dimethoate for 24 hours at $30^{\circ}C$ was greatly decreased when compared with that of the normal seeds. 13) The amount of oxygen consumption of the seeds (in 24 hours after 24 hours water soaking) was negatively correlated with the average germination periods of the seeds.

• Journal of Distribution Research
• /
• v.17 no.1
• /
• pp.65-86
• /
• 2012

The $20^{th}$ century was the era of manufacturer brands which built higher brand equity for consumers. Consumers moved from generic products of inconsistent quality produced by local factories in the $19^{th}$ century to branded products from global manufacturers and manufacturer brands reached consumers through distributors and retailers. Retailers were relatively small compared to their largest suppliers. However, sometime in the 1970s, things began to slowly change as retailers started to develop their own national chains and began international expansion, and consolidation of the retail industry from mom-and-pop stores to global players was well under way (Kumar and Steenkamp 2007, p.2) In South Korea, since the middle of the 1990s, the bulking up of retailers that started then has changed the balance of power between manufacturers and retailers. Retailer private labels, generally referred to as own labels, store brands, distributors own private-label, home brand or own label brand have also been performing strongly in every single local market (Bushman 1993; De Wulf et al. 2005). Private labels now account for one out of every five items sold every day in U.S. supermarkets, drug chains, and mass merchandisers (Kumar and Steenkamp 2007), and the market share in Western Europe is even larger (Euromonitor 2007). In the UK, grocery market share of private labels grew from 39% of sales in 2008 to 41% in 2010 (Marian 2010). Planet Retail (2007, p.1) recently concluded that "[PLs] are set for accelerated growth, with the majority of the world's leading grocers increasing their own label penetration." Private labels have gained wide attention both in the academic literature and popular business press and there is a glowing academic research to the perspective of manufacturers and retailers. Empirical research on private labels has mainly studies the factors explaining private labels market shares across product categories and/or retail chains (Dahr and Hoch 1997; Hoch and Banerji, 1993), factors influencing the private labels proneness of consumers (Baltas and Doyle 1998; Burton et al. 1998; Richardson et al. 1996) and factors how to react brand manufacturers towards PLs (Dunne and Narasimhan 1999; Hoch 1996; Quelch and Harding 1996; Verhoef et al. 2000). Nevertheless, empirical research on factors influencing the production in terms of a manufacturer-retailer is rather anecdotal than theory-based. The objective of this paper is to bridge the gap in these two types of research and explore the factors which influence on manufacturer's private label production based on two competing theories: S-C-P (Structure - Conduct - Performance) paradigm and resource-based theory. In order to do so, the authors used in-depth interview with marketing managers, reviewed retail press and research and presents the conceptual framework that integrates the major determinants of private labels production. From a manufacturer's perspective, supplying private labels often starts on a strategic basis. When a manufacturer engages in private labels, the manufacturer does not have to spend on advertising, retailer promotions or maintain a dedicated sales force. Moreover, if a manufacturer has weak marketing capabilities, the manufacturer can make use of retailer's marketing capability to produce private labels and lessen its marketing cost and increases its profit margin. Figure 1. is the theoretical framework based on a strategic market management perspective, integrated concept of both S-C-P paradigm and resource-based theory. The model includes one mediate variable, marketing capabilities, and the other moderate variable, competitive intensity. Manufacturer's national brand reputation, firm's marketing investment, and product portfolio, which are hypothesized to positively affected manufacturer's marketing capabilities. Then, marketing capabilities has negatively effected on private label production. Moderating effects of competitive intensity are hypothesized on the relationship between marketing capabilities and private label production. To verify the proposed research model and hypotheses, data were collected from 192 manufacturers (212 responses) who are producing private labels in South Korea. Cronbach's alpha test, explanatory / comfirmatory factor analysis, and correlation analysis were employed to validate hypotheses. The following results were drawing using structural equation modeling and all hypotheses are supported. Findings indicate that manufacturer's private label production is strongly related to its marketing capabilities. Consumer marketing capabilities, in turn, is directly connected with the 3 strategic factors (e.g., marketing investment, manufacturer's national brand reputation, and product portfolio). It is moderated by competitive intensity between marketing capabilities and private label production. In conclusion, this research may be the first study to investigate the reasons manufacturers engage in private labels based on two competing theoretic views, S-C-P paradigm and resource-based theory. The private label phenomenon has received growing attention by marketing scholars. In many industries, private labels represent formidable competition to manufacturer brands and manufacturers have a dilemma with selling to as well as competing with their retailers. The current study suggests key factors when manufacturers consider engaging in private label production.

• Journal of Korean Society of Forest Science
• /
• v.82 no.2
• /
• pp.152-165
• /
• 1993

This is the basic study in order to know the amount of transpirational water loss in a Larix leptorepis stand by a heat pulse method. Especially this study has been measured and discussed the diurnal and seasonal trends of heat pulse velocity by changes of radiation, temperature and humidity, differences of heat pulse velocity by direction and depth in stem, differences of heat pulse velocity by dominant, codominant and suppressed trees, diurnal change of heat pulse velocity by change of leaf water potential, sap flow path way in sapwood by dye penetration and amount of daily and annual transpiration in a tree and stand. The results obtained as follows : 1. Relation between heat pulse velocity(V) and sap flow rate(SFR) was established as a equation of SFR=1.37V($r=0.96^{**}$). 2. The sap flow rate presented in the order of dominant, codominant and suppressed tree, respectively. The daily heat pulse velocity was changed by radiation, temperature and vapor pressure deficit. 3. The heat pulse velocity in individual trees did not differ in early morning and in late night, but had some differed from 12 to 16 hours when radiation was relatively high. 4. The heat pulse velocity and leaf water potential showed similar diurnal variation. 5. The seasonal variation of heat pulse velocity was highest in August, but lowest in October and similar value of heat pulse velocity in the other months. 6. The heat pulse velocity in stem by direction was highest in eastern, but lowest in southern and similar velocity in western and northern. 7. The difference of heat pulse velocity in according to depths was highest in 2.0cm depth, medium in 1.0cm depth, and lowest in 3.0cm depth from surface of stem. 8. The sap flow path way in stem showed spiral ascent turning right pattern in five sample trees, especially showed little spiral ascent turning right in lower part than 3m hight above ground, but very speedy in higher than 3m hight. 9. The amount of sap flow(SF) was presented as a equation of SF=1.37AV and especially SF in dominant tree was larger than in codominant or suppressed tree. 10. The amount of daily transpiration was 30.8ton/ha/day and its composition ratio was 83% at day and 17% at night. 11. The amount of stand transpiration per month was largest in August(1,194ton/ha/month), lowest in May (386ton/ha/month). The amount of stand transpiration per year was 3,983ton/ha/year.

• Korean Journal of Animal Reproduction
• /
• v.26 no.1
• /
• pp.17-23
• /
• 2002

The present study was carried out to investigate the effects of the maturation media such as a modified TCM-199 (mTCM-199) medium, modified Waymouth MB 752/1 (mWaymouth MB 752/1) medium or NCSU-23 medium on penetrability of pig oocytes by liquid boar sperm. Oocytes (30~40) were transferred into each well of a Nunc 4-well multidish containing 0.5 $m\ell$ maturation medium. When immature pig oocytes were cultured in mTCM-199, mWaymouth MB 752/1 and NCSU-23 maturation media for 44 h in 5% $CO_2$, in air at 38.5$^{\circ}C$, the germinal vesicle breakdown (CVBD) rates of the oocytes were 95.6, 94.1 and 94.9%, respectively, and the maturation rates (metaphase II) of oocytes were 92.5, 90.1 and 91.1%, respectively. No differences were observed among the maturation media. The spermrich portion of ejaculates with greater than 90% motile sperm were used in the experiment. The semen was cooled 22 to 24$^{\circ}C$ over 2 h period. The semen was diluted with Beltsville Thawing Solution (BTS) extender at room temperature to give 2$\times$10$^{8}$ sperm/$m\ell$ in 100 $m\ell$ plastic bottle. Liquid boar semen of 30 $m\ell$ in 100 $m\ell$ plastic bottle was kept at 17$^{\circ}C$ for 5 days. The sperm with greater than 70% motility after day 5 of storage were used for in-vitro fertilization (IVF). After 44 h maturation of immature oocytes, cumulus cells were removed and oocytes (30~40) coincubated far 6 h in 0.5 $m\ell$ mTCM-199 and mTBM fertilization media with 2$\times$1061$m\ell$ sperm concentration. At 6 h after IVF, oocytes were transferred into 0.5 $m\ell$ mTCM-199 and NCSU-23 culture media for further culture 6 or 42 h. Sperm penetration, polyspermy and male pronuclear formation of oocytes at 12 h after IVF, and developmental ability of oocytes at 48 h after IVF were evaluated. The oocytes in combination with NCSU-23 medium for maturation and mTBM medium for IVF increased male pronuclear formation (48.0%) compared to those in combination with mTCM-199 media for maturation and IVF, and mWaymouth MB 752il medium for maturation and mTCM-199 medium far IVF. The rates of cleaved embryos (2~4 cell stage) at 48 h after IVF were 24.1% in combination with mTCM-199 media for maturation, IVF and culture, 43.6% in combination with mWaymouth MB 75211 medium fur maturation and mTCM-199 media for IVF and culture, and 71.2% in combination with NCSU-23 medium for maturation, mTBM medium for IVF and NCSU-23 medium for culture. In conclusion, we found out the oocytes matured in vitro were fertilized by liquid boar sperm stored in BTS extender at 17$^{\circ}C$ for 5 days. We recommend the simple defined NCSU-23 medium for nuclear maturation, mTBM medium and liquid boar sperm for IVF, and NCSU-23 medium for embryo culture.

• Restorative Dentistry and Endodontics
• /
• v.27 no.2
• /
• pp.158-174
• /
• 2002

The aim of this study was to investigate the effect of light irradiation modes on polymerization shrinkage, degree of cure and microleakage of a composite resin. VIP$^{TM}$ (Bisco Dental Products, Schaumburg, IL, USA) and Optilux 501$^{TM}$ (Demetron/Kerr, Danbury, CT, USA) were used for curing Filtek$^{TM}$ Z-250 (3M Dental Products, St. Paul., MN, USA) composite resin using following irradiation modes: VIP$^{TM}$ (Bisco) 200mW/$\textrm{cm}^2$ (V2), 400mW/$\textrm{cm}^2$ (V4), 600mW/$\textrm{cm}^2$ (V6), Pulse-delay (200 mW/$\textrm{cm}^2$ 3 seconds, 5 minutes wait, 600mW/$\textrm{cm}^2$ 30seconds, VPD) and Optilux 501$^{TM}$ (Demetron/Kerr) C-mode (OC), R-mode (OR). Linear polymerization shrinkage of the composite specimens were measured using Linometer (R&B, Daejeon, Korea) for 90 seconds for V2, V4, V6, OC, OR groups and for up to 363 seconds for VPD group (n=10, each). Degree of conversion was measured using FTIR spectrometer (IFS 120 HR, Bruker Karlsruhe, Germany) at the bottom surface of 2 mm thick composite specimens V2, Y4, V6, OC groups were measured separately at five irradiation times (5, 10, 20, 40, 60 seconds) and OR, VPD groups were measured in the above mentioned irradiation modes (n=5 each). Microhardness was measured using Digital microhardness tester (FM7, Future-Tech Co., Tokyo, Japan) at the top and bottom surfaces of 2mm thick composite specimens after exposure to the same irradiation modes as the test of degree of conversion(n=3, each). For the microleakage test, class V cavities were prepared on the distal surface of the ninety extracted human third molars. The cavities were restored with one of the following irradiation modes : V2/60 seconds, V4/40 seconds, V6/30 seconds, VPD , OC and OR. Microleakage was assessed by dye penetration along enamel and dentin margins of cavities. Mean polymerization shrinkage, mean degree of conversion and mean microhardness values for all groups at each time were analyzed using one-way ANOVA and Duncan's multiple range test, and using chi-square test far microleakage values. The results were as follows : . Polymerization shrinkage was increased with higher light intensity in groups using VIP$^{TM}$ (Bisco) : the highest with 600mW/$\textrm{cm}^2$, followed by Pulse-delay, 400mW/$\textrm{cm}^2$ and 200mW/$\textrm{cm}^2$ groups, The degree of polymerization shrinkage was higher with Continuous mode than with Ramp mode in groups using Optilux 501$^{TM}$ (Demetron/Kerr). . Degree of conversion and microhardness values were higher with higher light intensity. The final degree of conversion was in the range of 44.7 to 54.98% and the final microhardness value in the range of 34.10 to 56.30. . Microleakage was greater in dentin margin than in enamel margin. Higher light intensity showed more microleakage in dentin margin in groups using VIP$^{TM}$ (Bisco). The microleakage was the lowest with Continuous mode in enamel margin and with Ramp mode in dentin margin when Optilux 501$^{TM}$ (Demetron/Kerr) was used.

• Journal of Intelligence and Information Systems
• /
• v.23 no.3
• /
• pp.69-94
• /
• 2017

Recently, increase of demand for big data analysis has been driving the vigorous development of related technologies and tools. In addition, development of IT and increased penetration rate of smart devices are producing a large amount of data. According to this phenomenon, data analysis technology is rapidly becoming popular. Also, attempts to acquire insights through data analysis have been continuously increasing. It means that the big data analysis will be more important in various industries for the foreseeable future. Big data analysis is generally performed by a small number of experts and delivered to each demander of analysis. However, increase of interest about big data analysis arouses activation of computer programming education and development of many programs for data analysis. Accordingly, the entry barriers of big data analysis are gradually lowering and data analysis technology being spread out. As the result, big data analysis is expected to be performed by demanders of analysis themselves. Along with this, interest about various unstructured data is continually increasing. Especially, a lot of attention is focused on using text data. Emergence of new platforms and techniques using the web bring about mass production of text data and active attempt to analyze text data. Furthermore, result of text analysis has been utilized in various fields. Text mining is a concept that embraces various theories and techniques for text analysis. Many text mining techniques are utilized in this field for various research purposes, topic modeling is one of the most widely used and studied. Topic modeling is a technique that extracts the major issues from a lot of documents, identifies the documents that correspond to each issue and provides identified documents as a cluster. It is evaluated as a very useful technique in that reflect the semantic elements of the document. Traditional topic modeling is based on the distribution of key terms across the entire document. Thus, it is essential to analyze the entire document at once to identify topic of each document. This condition causes a long time in analysis process when topic modeling is applied to a lot of documents. In addition, it has a scalability problem that is an exponential increase in the processing time with the increase of analysis objects. This problem is particularly noticeable when the documents are distributed across multiple systems or regions. To overcome these problems, divide and conquer approach can be applied to topic modeling. It means dividing a large number of documents into sub-units and deriving topics through repetition of topic modeling to each unit. This method can be used for topic modeling on a large number of documents with limited system resources, and can improve processing speed of topic modeling. It also can significantly reduce analysis time and cost through ability to analyze documents in each location or place without combining analysis object documents. However, despite many advantages, this method has two major problems. First, the relationship between local topics derived from each unit and global topics derived from entire document is unclear. It means that in each document, local topics can be identified, but global topics cannot be identified. Second, a method for measuring the accuracy of the proposed methodology should be established. That is to say, assuming that global topic is ideal answer, the difference in a local topic on a global topic needs to be measured. By those difficulties, the study in this method is not performed sufficiently, compare with other studies dealing with topic modeling. In this paper, we propose a topic modeling approach to solve the above two problems. First of all, we divide the entire document cluster(Global set) into sub-clusters(Local set), and generate the reduced entire document cluster(RGS, Reduced global set) that consist of delegated documents extracted from each local set. We try to solve the first problem by mapping RGS topics and local topics. Along with this, we verify the accuracy of the proposed methodology by detecting documents, whether to be discerned as the same topic at result of global and local set. Using 24,000 news articles, we conduct experiments to evaluate practical applicability of the proposed methodology. In addition, through additional experiment, we confirmed that the proposed methodology can provide similar results to the entire topic modeling. We also proposed a reasonable method for comparing the result of both methods.

• Journal of Intelligence and Information Systems
• /
• v.20 no.4
• /
• pp.59-87
• /
• 2014

In MIS field, the researches on payment services are focused on adoption factors of payment service using behavior theories such as TRA(Theory of Reasoned Action), TAM(Technology Acceptance Model), and TPB (Theory of Planned Behavior). The previous researches presented various adoption factors according to types of payment service, nations, culture and so on even though adoption factors of identical payment service were presented differently by researchers. The payment service industry relatively has strong path dependency to the existing payment methods so that the research results on the identical payment service are different due to payment culture of nation. This paper aims to suggest a successful adoption factor of noble payment service regardless of nation's culture and characteristics of payment and prove it. In previous researches, common adoption factors of payment service are convenience, ease of use, security, convenience, speed etc. But real cases prove the fact that adoption factors that the previous researches present are not always critical to success to penetrate a market. For example, PayByPhone, NFC based parking payment service, successfully has penetrated to early market and grown. In contrast, Google Wallet service failed to be adopted to users despite NFC based payment method which provides convenience, security, ease of use. As shown in upper case, there remains an unexplained aspect. Therefore, the present research question emerged from the question: "What is the more essential and fundamental factor that should takes precedence over factors such as provides convenience, security, ease of use for successful penetration to market". With these cases, this paper analyzes four cases predicted on the following hypothesis and demonstrates it. "To successfully penetrate a market and sustainably grow, new payment service should find non-customer of the existing payment service and provide noble payment method so that they can use payment method". We give plausible explanations for the hypothesis using multiple case studies. Diners club, Danal, PayPal, Square were selected as a typical and successful cases in each category of payment service. The discussion on cases is primarily non-customer analysis that noble payment service targets on to find the most crucial factor in the early market, we does not attempt to consider factors for business growth. We clarified three-tier non-customer of the payment method that new payment service targets on and elaborated how new payment service satisfy them. In case of credit card, this payment service target first tier of non-customer who can't pay for because they don't have any cash temporarily but they have regular income. So credit card provides an opportunity which they can do economic activities by delaying the date of payment. In a result of wireless phone payment's case study, this service targets on second of non-customer who can't use online payment because they concern about security or have to take a complex process and learn how to use online payment method. Therefore, wireless phone payment provides very convenient payment method. Especially, it made group of young pay for a little money without a credit card. Case study result of PayPal, online payment service, shows that it targets on second tier of non-customer who reject to use online payment service because of concern about sensitive information leaks such as passwords and credit card details. Accordingly, PayPal service allows users to pay online without a provision of sensitive information. Final Square case result, Mobile POS -based payment service, also shows that it targets on second tier of non-customer who can't individually transact offline because of cash's shortness. Hence, Square provides dongle which function as POS by putting dongle in earphone terminal. As a result, four cases made non-customer their customer so that they could penetrate early market and had been extended their market share. Consequently, all cases supported the hypothesis and it is highly probable according to 'analytic generation' that case study methodology suggests. We present for judging the quality of research designs the following. Construct validity, internal validity, external validity, reliability are common to all social science methods, these have been summarized in numerous textbooks(Yin, 2014). In case study methodology, these also have served as a framework for assessing a large group of case studies (Gibbert, Ruigrok & Wicki, 2008). Construct validity is to identify correct operational measures for the concepts being studied. To satisfy construct validity, we use multiple sources of evidence such as the academic journals, magazine and articles etc. Internal validity is to seek to establish a causal relationship, whereby certain conditions are believed to lead to other conditions, as distinguished from spurious relationships. To satisfy internal validity, we do explanation building through four cases analysis. External validity is to define the domain to which a study's findings can be generalized. To satisfy this, replication logic in multiple case studies is used. Reliability is to demonstrate that the operations of a study -such as the data collection procedures- can be repeated, with the same results. To satisfy this, we use case study protocol. In Korea, the competition among stakeholders over mobile payment industry is intensifying. Not only main three Telecom Companies but also Smartphone companies and service provider like KakaoTalk announced that they would enter into mobile payment industry. Mobile payment industry is getting competitive. But it doesn't still have momentum effect notwithstanding positive presumptions that will grow very fast. Mobile payment services are categorized into various technology based payment service such as IC mobile card and Application payment service of cloud based, NFC, sound wave, BLE(Bluetooth Low Energy), Biometric recognition technology etc. Especially, mobile payment service is discontinuous innovations that users should change their behavior and noble infrastructure should be installed. These require users to learn how to use it and cause infra-installation cost to shopkeepers. Additionally, payment industry has the strong path dependency. In spite of these obstacles, mobile payment service which should provide dramatically improved value as a products and service of discontinuous innovations is focusing on convenience and security, convenience and so on. We suggest the following to success mobile payment service. First, non-customers of the existing payment service need to be identified. Second, needs of them should be taken. Then, noble payment service provides non-customer who can't pay by the previous payment method to payment method. In conclusion, mobile payment service can create new market and will result in extension of payment market.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.33 no.1
• /
• pp.52-64
• /
• 2015

This research traced the characteristics of the semantic landscape, construction intent, landscape composition, and geomantic conditions of the area subject to the research based on the research methods of 'field investigation, document studies, and interviews,' centering around the entire area of Gokseong Hamheo-pavilion (Jeonnam Tangible Cultural Assets No. 160). The result of the research, specifically revealing the forms and methods by which the reciprocal view of nature and landscape composition appearing in the landscape of the entire area of Hamheo-pavilion, as part of the analysis and interpretation over the view-based construction characteristics and position of the entire area of Gokseong Hamheo-pavilion, can be summarized as follows. First, Hamheo-pavilion is a pavilion built as a resting area and as a venue for educational activities in 1543 in the nearby areas after Gwang-hyeon Sim founded Gunjichon-jeongsa for educational activities and dwelling purposes at Gunchon at the 30th year of King Jungjong. Gunchon, where Hamheo-pavilion and Gunjichon-jeongsa is located, exhibits the typical form having water in the front, facing Sunja-river(present Seomjin-river), and a mountain in the back side. Dongak-mountain, which is a guardian mountain, is in a snail-type form where cows leisurely ruminate and lie on the riverside, and the Hamheo-pavilion area is said to be an area bordering on one's way of enjoying peace and richness as it is a place with plentiful grass bushes available for cows to ruminate and lie down while sheppards may leisurely play their flutes at the riverside. The back hill of Hamheo-pavilion is a blood vessel that enters the water into the underwater palace of the turtle, and the building sitting on the turtle's back is Hamheo-pavilion, and the Guam-jodae(龜巖釣臺) and lava on the southern side below the cliff can be interpreted to be the underwater fairly land wanted by the turtle.6) Second, Hamheo-pavilion is the scenery viewpoint of Sungang-Cheongpung (3rd Scenery) and Seolsan-Nakjo(雪山落照, 9th Scenery) among the eight sceneries of Gokseong, while also the scenery viewpoint of Hamheo-Sunja(2nd Scenery) and Cheonma-Gwiam(天馬歸岩, 3rd Scenery) among the eight sceneries of Ipmyeon. On the other hand, the pavilion is reproduced through the aesthetics of bends through sensible penetration and transcendental landscape viewed based on the Confucian-topos and ethics as the four bends among the five bends of Sunja-river arranged in the 'Santaegeuk(山太極) and Sutaeguek(水太極, formation of the yin-yang symbol by the mountain and water)' form, which is alike the connection of yin and yang. In particular, when based on the description over Mujinjeong (3rd Bend), Hoyeonjeong(4th Bend), andHapgangjeong(2nd Bend) among the five bends of Sunja-river in the records of Bibyeonsainbangan-jido(duringthe 18th century) and Okgwahyeonji(1788), the scenery of the five bends of Sunja-river allow to glimpse into its reputation as an attraction-type connected scenery in the latter period of the Joseon era, instead of only being perceived of its place identity embracing the fairyland world by crossing in and out of the world of this world and nirvana. Third, Hamheo-pavilion, which exhibits exquisite aesthetics of vacancy, is where the 'forest landscape composed of old big trees such as oak trees, oriental oak trees, and pine trees,' 'rock landscape such as Guam-jodae, lava, and layered rocks' and 'cultural landscape of Gunchon village' is spread close by. In the middle, it has a mountain scenery composed of Sunja-river, Masan-peak, and Gori-peak, and it is a place where the scenery by Gori-peak, Masan-peak, Mudeung-mountain, and Seol-mountain is spread and open in $180^{\circ}$ from the east to west. Mangseo-jae, the sarangchae (men's room)of Gunjichon-jeongsa, means a 'house observing Seoseok-mountain,' which has realized the diverse view-oriented intent, such as by allowing to look up Seol-mountain or Mudeung-mountain, which are back mountains behind the front mountain, through landscape configuration. Fourth, the private home, place for educational activities, pavilion, memorial room, and graveyard of Gunji-village, where the existence and ideal is connected, is a semantic connected scenery relating to the life cycle of the gentry linking 'formation - abundance - transcendence - regression.' In particular, based on the fact that the descriptions over reciprocal views of nature regarding an easy and comfortable life and appreciations for a picturesque scene of the areas nearby Sunja-river composes most of the poetic phrases relating to Hamheo-pavilion, it can be known that Hamheo-pavilion is expressed as the key to the idea of 'understanding how to be satisfied while maintaining one's positon with a comfortable mind' and 'returning to nature,' while also being expressed of its pedantic character as a place for reclusion for training one's mind and training others through metaphysical semantic scenery.