• Composites Research
• /
• v.26 no.3
• /
• pp.170-174
• /
• 2013

Atmospheric glow plasma polymerization was applied to wood powder before fabricating polypropylene (PP) matrix composites. Seven different types of monomers (Oxygen, Benzene, CH4, Acrylic-acid, Hexafluoroethane, Trifluorotolune, Hexamethyl-disiloxane) were analyzed to determine the most suitable precursor for plasma polymerization. The surface energy was calculated from measured contact angle about each monomer on PP. Hexamethyl-disiloxane (HMDSO) had a highest surface energy and is selected as the most suitable monomer. Wood powder and polypropylene were mixed as pellets by twin screw extruder and then 50 wt% wood powder/PP composites were produced by an injection machine. Tensile strength and Flexural strength have improved by 7.59% and 12.43% at the maximum respectively. SEM (Scanning Electron Microscope) observation on the fracture surface revealed that the plasma polymerization have improved the interfacial bonding and the mechanical properties of the composites.

• Journal of Periodontal and Implant Science
• /
• v.30 no.4
• /
• pp.821-836
• /
• 2000

The Peri-implantitis causes inflammation of periodontal tissue and bone loss. It contaminates surface of implants. Therefore, guided bone regeneration has been used for the treatment of this disease. For the reosseointegration of the exposed surface, various mechanical and chemical methods have been used for cleaning and detoxication of implant surface. Among these methods, air-powder abrasive and oversaturated citrate are known to be most effective. However, these treatments may deform implant surface. In this research, changes of surface roughness they were examined. 10 experimental machined titanium cylinder models were fabricated to be used for control groups. Each of them was air powder abraded for 1 minute and they were named group 1. And then, group 1 were burnished with cotton pellets soaked with citrate for 30 seconds(Group 2), 1 minute(Group 3), 3 minutes(Group 4), and 5 minutes(Group 5) burnishing were applied for grouping respectively. Each group were examined with SPM, and their surface roughness were measured and analyzed. 1. Surface roughness of titanium decreased when it was air-powder abraded for 1 minute. It was statistically significant. 2. When Air-powder abraded titanium were treated with citrate for 3 minutes, Their surface roughness was the lowest. Titanium treated for 1 minute was the second lowest and 30 seconds was the third and titanium burnished for 5 minutes was the highest. 3. Surface roughness of titanium which was treated with citrate was decreased till 3 minutes, which was statistically significant. There was no statistical significance from 30 seconds to 1 minute and from 1 minute to 3 minutes, and there was statistical significance from 30 seconds to 3 minutes. 4. Oxide layer was formed when titanium is exposed to air, and it was removed when air-powder abraded. It was made when treated with citrate. It is thought that citrate treatment is necessary after the air-powder abrasion, and 1 minute is clinically and qualitatively adequate for burnishing time of citrate.

• Resources Recycling
• /
• v.17 no.3
• /
• pp.10-20
• /
• 2008

In order to study the behaviors of inorganic fillers in recycling of the waste agricultural plastic films, the washed PE fluffs from Shihwa and Jungeup Plant belonging to ENVICO were used respectively. First of all, the test pellets were manufactured by adding of inorganic fillers suchlike calcium carbonate and calpet by certain portions to PE fluffs and then the tested sheets were formed. The mechanical and thermal properties of the samples were measured and compared with others. The items measured were tensile, flexural, Izod impact, HDT, MFT, and so on. Morphologies were also investigated for various samples using the SEM. Finally, optimum ratios between recycled PE and inorganic additives were found out for the best products in physical condition as well as in economic point of view.

• Clean Technology
• /
• v.10 no.3
• /
• pp.121-130
• /
• 2004

Pelletizer of dry ice snow produced by adiabatic expansion of liquid carbon dioxide and their blaster were designed and manufactured. The blaster had a high cleaning power against various contaminants on the surface such as stain, oily dirt, lacquer film and paints with low blasting pressure and low consumption of blasting air. The capacity of hopper for dry ice pellet supply was 12 kg and the mass rate of pellet blasting was controlled in 0 to 1.2 kg/min. The impact of the pellets was independent of standoff distance within a certain limiting distance, and dependent on the impact stress, angle and mass rate of dry ice pellet blasting. On the other hand the cleaning power was influenced by thermal properties and surface roughness of the substrates and decreased in the order of glass, copper, brass, steel and acryl. The power was also affected by hardness and adhesion of the contaminant on the substrate, and decreased in the order of grease, epoxy and paint. The noise was detected during blasting in the range of 85 to 100dBA.

• Journal of Fisheries and Marine Sciences Education
• /
• v.26 no.3
• /
• pp.667-675
• /
• 2014

Two types of diets, extruded pellet (EP) and raw-fish-based moist pellet (MP) were fed to compare growth, water quality and histology of olive flounder, Paralichthys olivaceus in Jeju fish farm. Two groups of 7000 fish per each tank (initial mean weight 51 g) were fed one of two diets for 7 months. At the end of the feeding trial, significant differences were found in weight gain and feed utilization. Dissolved oxygen (DO) level of the MP tank was decreased from 7.98 to 6.89 after feeding. There were no significant differences in hematocrit, hemoglobin, alanine aminotransferase and aspartate aminotransferase of fish fed the two diets. Whole body protein content of fish fed the EP was significantly higher than that of fish fed the MP. While the feeding rate by month indicated numerically decreased, fish fed the MP had higher feed intake than that of fish fed the EP. Histological examination of hepatopancreas, kidney, and anterior intestine of fish fed the EP did not show any negative effects compared to those of fish fed the MP. This study revealed that EP could substitute for MP in terms of growth performance, blood parameters, water quality and histology of olive flounder.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.12 no.1
• /
• pp.1-6
• /
• 2002

The preparation of 0.9PMN-0.1PT ceramics by the metal alkoxide method and the effect of excess $Mg(OC_2H_5)_2$, $Pb(CH_3COO)_2{\cdot}3H_2O$ are reported. The excess$ Mg(OC_2H5)_2$ addition signficantly affects the rate of perovskite phase formation in 0.9PMN-0.1PT ceramics. The sample by addition of 5 wt% excess $Mg(OC_2H5)_2$ sintered at $1150^{\circ}C$ for 1 hr obtained perovskite single phase and showed 98% of the theoretical density. The dielectric constant of the pellets sintered at $1150^{\circ}C$ was increased by the addition of 5 wt% excess $Mg(OC_2H_5)_2$ and had a maximum value of 15000 at 1 kHz.

• Journal of the Korean Chemical Society
• /
• v.28 no.5
• /
• pp.293-301
• /
• 1984

-ray fluorescence analysis of $Ta_2O_5$, $Nb_2O_5$ and $ZrO_2$ in tin-slag samples using the simple dilution method was studied. The method is to correct mathematically the calibration curve to the linear line by the dilution. One synthesized standard having similar composition to the sample and tin slag samples were diluted with anhydrous $Li_2B_4O_7$ at the level of 1%, 2% and 3% of the sample content respectively. The diluted samples were fused at $1150^{\circ}C$ for 30 minutes and these glass beads were finely ground and pelletized. Measuring the X-ray intensities with these pellets, analytical results were calculated by the equation derived from J. Scherman's equation for the characteristic X-ray intensity of an element. Analytical results agreed with the reference values obtained by the standard calibration method within allowable error range and were reproducible.

• Clinical and Experimental Reproductive Medicine
• /
• v.21 no.3
• /
• pp.261-266
• /
• 1994

Semen preparation for Assisted Reproductive Technology(ART) involves the separation of the motile sperm from non-motile, dead sperm, cellular debris and seminal fluid. The aim of this study is to compare the motile sperm recovery rate and motility index of different sperm preparation method(swim-up method, 80% isotonic continuous percoll method, two-layer discontinuous percoll method, mini-percoll method). In Mini-Percoll method, pellets from patients were suspended in 0.3ml of medium and layerd on a discontinuous percoll gradient consisting of 0.3ml each of 50, 70, 95% isotonic percoll. All semen samples are divided into normal and subnormal sperm group(oligo-, astheno-, oligoasthenozoospermia). Especially, we evaluated the effect of mini-percoll method in subnormal sperm group. In normal sperm group, mini-percoll method and two layer discontinuous percoll method (40%/80%) allowed increasing of motile sperm recovery rate. But motility index was higher in swimup method than the other methods. In subnormal sperm group, mini-percoll method has advantages as compare with the other methods in motile sperm recovery rate and motility index. These results suggest that modified mini-percoll method could be certainly a valuable tool in some cases of severe male factor sperm.

• Nuclear Engineering and Technology
• /
• v.36 no.6
• /
• pp.528-539
• /
• 2004

It is essential in commercial reactors that the safety limits imposed on the fuel pellets and fuel clad barriers, such as the linear power density (LPD) and the departure from nucleate boiling ratio (DNBR), are not violated during reactor operations. In order to accurately monitor the safety limits of current reactor states, a detailed three-dimensional (3D) core power distribution should be estimated from the in-core detector signals. In this paper, we propose a calculation methodology for detailed 3D core power distribution, using in-core detector signals and core monitoring constants such as the 3D Coupling Coefficients (3DCC), node power fraction, and pin-to-node factors. Also, the calculation method for several core safety parameters is introduced. The core monitoring constants for the real core state are promptly provided by the core design code and on-line MASTER (Multi-purpose Analyzer for Static and Transient Effects of Reactors), coupled with the core monitoring program. through the plant computer, core state variables, which include reactor thermal power, control rod bank position, boron concentration, inlet moderator temperature, and flow rate, are supplied as input data for MASTER. MASTER performs the core calculation based on the neutron balance equation and generates several core monitoring constants corresponding to the real core state in addition to the expected core power distribution. The accuracy of the developed method is verified through a comparison with the current CECOR method. Because in all the verification calculation cases the proposed method shows a more conservative value than the best estimated value and a less conservative one than the current CECOR and COLSS methods, it is also confirmed that this method secures a greater operating margin through the simulation of the YGN-3 Cycle-1 core from the viewpoint of the power peaking factor for the LPD and the pseudo hot pin axial power distribution for the DNBR calculation.

• Journal of Adhesion and Interface
• /
• v.2 no.4
• /
• pp.24-31
• /
• 2001

Polypropylenes(PP) with different melt index values were mixed with ethylene-propylene rubber(EPR) or ethylene-propylene diene monomer rubber(EPDM) and an ethylene copolymer containing carboxylic acid group in a twin screw extruder. Then test specimens were prepared from the pellets of the blends with an injection molding machine. The mechanical properties and morphology of fractured surfaces were measured. Relative peak intensities of carboxylic acid group on the specimen surface were measured with an attennuated total reflection infrared spectrometer (ATR-IR) and compared with each other. The blend specimens were found to have the gradient morphology of rubber domains in PP matrix in the core region and PP skin layer. The blends containing PP of higher melt index showed greater content of ethylene copolymer containing carboxylic acid on the surface when the relative peak intensities of ATR-IR for carboxylic acid were compared. As the melt index values were increased, the decrease tendency in mechanical propeties such as tensile strength and impact strength was more significant for PP/EPR blends than PP/EPDM blends.