• Korean Chemical Engineering Research
• /
• v.49 no.6
• /
• pp.775-780
• /
• 2011

5-cell DMFC stack was fabricated and operated with the load of 4 A for 4000 hrs. After 4000 hrs operation peak power density of the stack reduced by 27.3%. Two of the five cells did now show performance degradation, the performance of other two was reduced by 40% and the performance of the other decreased by 60%. The amount of performance degradation of each cell by long-term operation did not correlate with the position in the stack. Platinum particle size in the anode catalyst layer of the MEA with the strongest degradation increased and the increase was severer on the position of methanol inlet than on the position of methanol outlet. However, platinum particle size in the cathode catalyst layers did not changed for all the MEA'. Ruthenium crossover from the anode catalyst layer to the cathode catalyst layer through the membrane was observed after 4,000 hrs operation by SEM-EDX and it occurred for all MEA' regardless of the degree of performance degradation. Atomic ratio of ruthenium to platinum in the cathode catalyst layer was the highest in the MEA with the strongest performance degradation.

• Journal of the Korean Society of Food Culture
• /
• v.28 no.6
• /
• pp.664-673
• /
• 2013

This study was conducted to investigate the physicochemical properties of mung bean starch and the quality characteristics of mung bean starch gels supplemented with gelatin and isolated soy protein (0, 2, 5%) during storage at $5^{\circ}C$ for 0, 24, 48, and 72 hours. The swelling power of mung bean starch supplemented with gelatin did not significantly change, whereas those supplemented with isolated soy protein (ISP) significantly increased. The solubility of mung bean starch supplemented with gelatin and ISP, however, significantly increased with increasing concentration. In addition, the soluble amylose and soluble carbohydrate of mung bean starch supplemented with gelatin and ISP significantly decreased with increasing concentration. In terms of pasting properties measured by the Rapid Visco Analyzer (RVA), the pasting temperature of mung bean starch supplemented with gelatin and ISP was not significantly different, whereas peak viscosity, minimum viscosity, final viscosity, breakdown, and consistency decreased. DSC thermograms showed that the onset temperature of mung bean starch supplemented with gelatin and ISP did not significantly change, whereas the enthalpy increased with the addition of 5% ISP. The lightness (L) and redness (a) of mung bean starch gels supplemented with gelatin, ISP, and without additives increased during cold storage, whereas the yellowness (b) decreased. The addition of gelatin and ISP suppressed changes in L, a and b of mung bean starch gel during cold storage. Synereses of mung bean starch gel supplemented with gelatin and ISP was lower than that without additives, with the addition of gelatin suppressing synereses more than ISP. The addition of gelatin and ISP also suppressed increases in hardness, chewiness, and gumminess of mung bean starch gels during cold storage. In the sensory evaluation, the addition of gelatin and ISP suppressed increases in hardness and brittleness of mung bean starch gels during cold storage. The addition of 2%, 5% gelatin and 2% ISP also suppressed a decrease in the overall acceptability of mung bean starch gels during 24-48 hr cold storage. Thus, the addition of 2-5% gelatin and 2% ISP to mung bean starch is appropriate for suppressing the quality deterioration of 24-48 hr cold-stored mung bean starch gels.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.214-214
• /
• 1999

다이아몬드를 반도체용 열방산용기판 등으로 사용하기 위해서는 수백 $\mu\textrm{m}$ 두께의 대면적 웨이퍼가 요구된다. 이를 위해서 DC are jet CVD, MW PACVD, DC PACVD 등이 개발되어, 현재 4"에서 8"까지의 많은 문제를 일으키고 있다. 본 연구에서는 multi-cathode DC PACVD법에 의한 4" 다이아몬드 웨이퍼의 합성과 합성된 막의 특성변화에 대한 연구를 수행하였다. 또한, 웨이퍼의 휨과 crack 발생거동과 대한 고찰을 통래 휨과 crack이 없는 웨이퍼의 제작방법을 고안하였다. 사용된 음극의 수는 일곱 개이며, 투입된 power는 각 음극 당 약 2.5kW(4.1 A-600V)이었다. 사용된 기판의 크기는 직경 4"이었다. 합성압력은 100Torr, 가스유량은 150sccm, 증착온도는 125$0^{\circ}C$~131$0^{\circ}C$, 수소가스네 메탄조성은 5%~8%이었다. 합성 중 막에 인가되는 응력은 합성 중 증착온도의 변화에 의해 제어하였다. 막의 결정도는 Raman spectroscopy 및 열전도도를 측정을 통해 분석하였다. 성장속도 및 다이아몬드 peak의 반가폭은 메탄조성 증가(5%~8%)에 따라 증가하여 각각 6.6~10.5$\mu\textrm{m}$/h 및 3.8~5.2 cm-1의 분포를 보였다. 6%CH4 및 7%CH4에서 합성된 웨이퍼에서 측정된 막의 열전도도는 11W/cmK~13W/cmK 정도로 높게 나타났다. 막두께의 uniformity는 최대 3.5%로 매우 균일하였다. 막에 인가되는 응력의 제어로 직경 4"k 합성면적에서 두께 1mm 이상의 균열 및 휨이 없는 다이아몬드 자유막 웨이퍼를 합성할 수 있었다.다이아몬드 자유막 웨이퍼를 합성할 수 있었다.active ion에 의해 sputtering 이 된다. 이때 plasma 처리기의 polymer 기판 후면에 magnet를 설치하여 높은 ionization을 발생시켜 처리 효과를 한층 높여 주었다. 이 plasma 처리는 표면 청정화, 표면 etching 이 동시에 행하는 것과 함께 장시간 처리에 의해 표면에서는 미세한 과, C=C기, -C-O-의 극성기의 도입에 의한 표면 개량이 된다는 것을 관찰할 수 있다. OPP polymer 표면을 Ar 100%로 plasma 처리한 경우 C-O, C=O 등의 carbonyl가 발생됨을 알 수 있었다. C-O, C=O 등의 carbynyl polor group이 도입됨에 따라 sputter된 Al의 접착력이 향상됨을 알 수 있으며, TEM 관찰 결과 grain size도 상당히 작아짐을 알 수 있었다.onte-Carlo 방법으로 처리하였다. 정지기장해석의 경우 상용 S/W인 Vector Fields를 사용하였다. 이를 통해 sputter 내 플라즈마 특성, target으로 입사하는 이온에너지 및 각 분포, 이들이 target erosion 형상에 미치는 영향을 살펴보았다. 또한 이들 결과로부터 간단한 sputtering 모델을 사용하여 target으로부터 sputter된 입자들이 substrate에 부착되는 현상을 Monte-Carlo 방법으로 추적하여 성막특성도 살펴보았다.다.다양한 기능을 가진 신소재 제조에 있다. 또한 경제적인 측면에서도 고부가 가치의 제품 개발에 따른 새로운 수요 창출과 수익률 향상, 기존의 기능성 안료를 나노(nano)화하여 나노 입자를 제조, 기존의 기능성 안료에 대한 비용 절감 효과등을 유도 할 수 있다. 역시 기술적인 측면에서도 특수소재 개발에 있어 최적의 나노 입자 제어기술 개발 및 나노입자를 기능성 소재로 사용하여 새로운 제품의 제조와 고압 기상

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.229-229
• /
• 1999

교류형 플라즈마 방전 표시기(AC Plasma Display Panel, AC PDP)의 구동에서의 방전 현상은 기입방전, 유지방전, 소거 방전이 있다. 이중 유지 방전은 표시장치로서의 휘도와 계조의 표현을 위한 방전으로 표시기로서의 효율을 결정하게 된다. 본 연구에서는 유지 방전 전압의 상승 시간의 변화에 따른 방전현상과 휘도, 효율의 변화를 살펴 보았다. 방전 현상에서의 가장 큰 변화는 교류형 플라즈마 방전 표시기의 방전 개시 전압과 방전 유지 전압의 변화이다. 유지 전압의 상승시간이 증가할수록 방전 개시 전압과 방전 유지 전압의 변화이다. 유지 전압의 상승 시간이 증가할수록 방전 개시 전압과 방전 유지 전압의 차(sustain margin)는 감소하여 상승 시간이 1$\mu$s/100V 이상의 영역에서는 방전 개시 전압과 방전 유지 전압이 차이가 없어지게 된다. 이는 방전 유지 전극 위의 유전체에 쌓이게 되는 벽전하(wall charge) 양의 감소에 의한 방전 약화의 영향을 보여질 수 있다. 그러나 방전 유지 전압의 형태와 전류의 시간적인 변화를 살펴보면 이러한 약한 방전은 벽전하의 감소에 의한 방전 시의 전계 감소보다는 방전 전류의 발생 시간이 방전 전압이 증가하여 최고점에 이르지 못한 시간에 위치하여 방전이 형성될 때의 전계가 강하지 못하기 때문인 것을 알 수 있다. 방전 전류를 측정한 결과에 의하면 방전 전류의 시작은 변위 전류가 흐르고 난 후부터 시작되며 그 결과 방전 전류가 최고점에 도달하는 시간은 방전 전압 상승 시간이 길어질수록 낮은 전압에서 형성되게 된다. 또한 방전 유지 전압의 상승 시간이 길어질수록 플라즈마 방전표시기의 휘도와 효율은 낮아지고 이 결과 또한 약한 전계에서의 방전에 의한 결과로 생각되어진다.플라즈마의 강도값을 입력하여 플라즈마의 radiation을 검출하고, 스퍼터링 공정중 실질적인 in-situ 정보로 이용하였다. PEM을 통하여 In/Sn의 플라즈마 강도변화를 조사하였다. 초기 In/Sn의 플라즈마 강도(intensity)는 강도를 100하여, 산소를 주입한 결과, plasma intensity가 35 줄어들었고, 이때 우수한 ITO 박막을 얻을 수 있었다. Pulsed DC power를 사용하여 아크 현상을 방지하였다. PET 상에 coating 된 ITO 박막의 표면저항과 광투과도는 4-point prove와 spectrophotometer를 이용하여 분석하였고, AES로 박막의 두께에 따른 성분비를 확인하였다. ITO 박막의 광투과도는 산소의 유량과 sputter 된 In/Sn ion의 plasma emission peak에 따라 72%-92%까지 변화하였으며, 저항은 37$\Omega$/$\square$ 이상을 나타내었다. 박막의 Sn/In atomic ratio는 0.12, O/In의 비율은 In2O3의 화학양론적 비율인 1.5보다 작은 1.3을 나타내었다.로 보인다.하면 수평축과 수직축의 분산 장벽의 비에 따라 cluster의 두께비가 달라지는 성장을 볼 수 있었고, 한 축 방향으로의 팔 넓이는 fcc(100) 표면의 경우 동일한 Ed+Ep값에 대응하는 팔 넓이와 거의 동일한 결과가 나타나는 것을 볼 수 있다. 따라서 이러한 비대칭적인 모양을 가지는 성장의 경우도 cluster 밀도, cluster 모양, cluster의 양 축 방향 길이 비, 양 축 방향의 평균 팔 넓이로부터 각 축 방향의 분산 장벽을 얻어낼 수 있을 것으로 보인다. 기대할 수 있는 여러 장점들을 보고하고자 한다.성이 우수한 시

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.4 s.95
• /
• pp.366-372
• /
• 2005

This paper presents analysis of a slot array antenna having a low side lobe level and high front-to-back ratio for a repeater system of a satellite DMB(Digital Multimedia Broadcasting) service. Antennas for this repeater system require a high gain and enough isolation to reduce interferences between signals in system. Therefore, it is necessary to suppress a side lobe level and to increase front-to-back ratio. Unlike a structure 134 by lossy microstrip lines, in this work a single cavity-backed slot antenna array using a single waveguide feed is proposed to obtain the reliability for high power handling and high radiation efficiency. The side lobe level and front-to-back ratio are enhanced with tapered array technique and an optimized vertical reflector. The measured side lobe levels in H- and E-plane are under $-33.24\;\cal{dB}$ and $-35.78\;\cal{dB}$, respectively. The front-to-back ratio over $37.84\;\cal{dB}$, and the peak gain of over $17\;\cal{dBi}$ are measured.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.7
• /
• pp.796-804
• /
• 2010

It is important to use the comb type pilot allocation for the continuous channel and efficient processing. And DFT-spreading OFDM is used a lot to solve high PAPR problem of OFDM system. However, PAPR is increased again when comb type pilot is used to estimate channel characteristics. So, in this paper, we employ a new SLM method to DFT-spreading OFDM system to reduce increased high PAPR. And we suggest an effective method to transmit side information without additional bandwidth. Pilot and side information must be preserved from jamming or intentional interferences since those are very important in DFT spread OFDM system using SLM. So, in this paper, we like to analyze and simulate the performance of DFT spread OFDM system based on SLM against jamming signal. To remedy the vulnerable shortcomings of DFT spread OFDM about jamming or intentional interferences, we employ FH(Frequency Hopping) method and analyze system performance under the several jamming conditions such as MTJ(Multi Tone Jamming) and PBJ(Partial Band Jamming).

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.12
• /
• pp.2511-2517
• /
• 2009

Recently, a FMCW radar is used for the various purposes in the short range detection and tracking of targets. The main advantages of a FMCWradar are the comparative simplicity of implementation and the low peak power transmission characterizing the very low probability of signal interception. Since it uses the frequency modulated continuous wave for transmission and demodulation, the received beat frequency represents the range and Doppler information of targets. Detection and extraction of useful information from targets are performed in this beat frequency domain. Therefore, the resolution and accuracy in the estimation of a beat spectrum are very important. However, using the conventional FFT estimation method, the high resolution spectrum estimation with a low sidelobe level is not possible if the acquisition time is very short in receiving target echoes. This kind of problems deteriorates the detection performance of adjacent targets having the large magnitude differences in return echoes and also degrades the reliability of the extracted information. Therefore, in this paper, the model parameter estimation methods such as autoregressive and eigenvector spectrum estimation are applied to mitigate these problems. Also, simulation results are compared and analyzed for further improvement.

• The Korean Journal of Archival Studies
• /
• no.66
• /
• pp.203-227
• /
• 2020

This article explores the influence of the king in the Joseon dynasty's document transmission system, focusing on some exceptional cases. According to the Joseon's law, the form of official documents depended on rank differences between receiver and sender. However, there were cases of not following the general principles such as Byungjo(兵曹), Seungjeongwon(承政院) and Kyujanggak(奎章閣). Byungjo was a ministry in charge of military administration. Seungjeongwon was a royal secretary institution which assisted the king and delivered king's orders that existed from the early Joseon. Kyujanggak was a royal library and an assistant institution of the king that was established in the JeongJo(正祖) era. Byungjo was regarded as a relatively high-ranking institution when it sent and received military-related documents. Seungjeongwon and Kyujanggak could use Kwanmoon(關文) to upper rank institution. Kwanmoon was the document form used for institutions of the same or lower rank than itself. Conversely, higher rank institutions used Cheobjeong(牒呈) which was stipulated as a document form to using upper rank institution in law to send them. The reason that they could have privileges in transmission document system was that Joseon had an administrative system centered on the king. Byungjo was an institution entrusted with military power from King. Seungjeonwon and Kyujanggak took charge of the assistance and the delivery of King's order. so they could have a different system of receiving and sending document than the others. In conclusion, the Joseon Dynasty operated exceptions in document administration based on the existence of the king, it means Joseon's transmission document system was basically operated under the Confucian bureaucracy with the king as its peak.

• Applied Biological Chemistry
• /
• v.26 no.2
• /
• pp.137-142
• /
• 1983

Starch granules of sweet potatoes, the Suwon 147 and the Chunmi were observed by photomicroscope and scanning electron microscope were round and polygonal. Granule sizes of the Suwon 147 and the Chunmi were $14{\sim}30{\mu}m,\;16{\sim}34{\mu}m$, respectively. X-ray diffraction pattern of starch granules resulted weak crystallinity at $2{\theta}$ 14.8, 17.2, 22.5. Starch granules were of the Ca crystalline type. The blue values of the Suwon 147 and the Chunmi were determined to be 0.342 and 0.279, amylose contents 27.6% and 23.6%, and water binding capacity 178.7% and 185.5%. Swelling of the starches negligible until $50^{\circ}C$ thereafter it increased rapidly. Swelling power of the Suwon 147 was more slightly than that of the Chunmi. Optical transmittance of 0.2% starch suspensions was increased rapidly from $65^{\circ}C$ and the gelatinization at $65{\sim}80^{\circ}C$ was of sing1e stage. Amylogram patterns of 4% starch solutions were similar to no peak viscosity. Viscosity of the Suwon 147 was increased, but that of the Chunmi was decreased at $92.5^{\circ}C$.

• Journal of the Korean Magnetic Resonance Society
• /
• v.12 no.1
• /
• pp.14-25
• /
• 2008

To investigate the 3-bond connectivity of human brain metabolites by scalar coupling interaction through 2D-correlation spectroscopy (COSY) techniques using high field NMR spectroscopy. All NMR experiments were performed at 298K on Unity Inova 500 or 600 (Varian Inc.) equipped with a triple resonance probe head with z-shield gradient. Human brain metabolites were prepared with 10% $D_2O$. Two dimensional 2D COSY spectra were acquired with 4096 complex data points in $t_2$ and 128 or 256 increments in $t_1$ dimension. The spectral width was 9615.4 Hz and solvent suppression was achieved using presaturation using low power irradiation of the water resonance during 2s of relaxation delay. NMR data were processed using VNMRJ (Varian Instrument) software and all the chemical shifts were referenced to the methyl resonance of N-acetyl aspartate (NAA) peak at 2.0 ppm. Total 10 metabolites such as N-acetyl aspartate (NAA), creatine (Cr), choline (Cho), glutamine (Gln), glutamate (Glu), myo-inositol (Ins), lactate (Lac), taurine (Tau), ${\gamma}$-aminobutyricacid (GABA), alanine (Ala) were included for major target metabolites. Symmetrical 2D-COSY spectra were successfully acquired. Total 14 COSY cross peaks were observed even though there were parallel/orthogonal noisy peaks induced by water suppression. Except for Cr, all of human brain metabolites produced COSY cross peaks. The spectra of NAA methyl proton at 2.02 ppm and Glu methylene proton ($CH_2(3)$) at 2.11 ppm and Gln methylene proton ($CH_2(3)$) at 2.14 ppm were overlapped in the similar resonance frequency between 2.00 ppm and 2.15 ppm. The present study demonstrated that in vitro 2D-COSY represented the 3-bond connectivity of human brain metabolites by scalar coupling interaction. This study could aid in better understanding the interactions between human brain metabolites in vivo 2D-COSY study. Also it would be helpful to determine the molecular stereochemistry in vivo by using two-dimensional MR spectroscopy.