• 제목/요약/키워드: Peak A/V Ratio

검색결과 193건 처리시간 0.021초

산소 분압비에 따른 $TiO_2$ 박막의 특성평가 (The properties of $TiO_2$ thin films by oxygen partial pressure)

  • 양현훈;임정명;박중윤;정운조;박계춘
    • 한국전기전자재료학회:학술대회논문집
    • /
    • 한국전기전자재료학회 2003년도 춘계학술대회 논문집 센서 박막재료 반도체 세라믹
    • /
    • pp.154-157
    • /
    • 2003
  • $TiO_2$ thin films were fabricated by RF magnetron sputtering system at by controlling deposition times, ratios of $Ar:O_2$ partial presser ratio and substrate conditions. And the surface, cross-section morphology, microstructure, and composition ratio of the films were analyzed by FE-SEM, TEM and XPS. Besides, the optical absorption and transmittance of the $TiO_2$ films were measured by a UV-VIS-NIR Spectrophotometer, and photocatalytic properties were studied by G${\cdot}$C Analyzer & Data Analysis system. As the result, when $TiO_2$ thin film was made at deposition time of 120[min] and $Ar:O_2$ ratio of 60:40, the best structural and optical properties among many thin films could be accepted. The best results of properties were as follows: thickness; 360~370[nm), grain size; 40[nm], gap between two peak binding energy; $5.8{\pm}0.05[eV]$ ($2_{p3/2}$ peak and $2_{p1/2}$ peak of Ti was show at $458.3{\pm}0.05[eV]$ and $464.1{\pm}0.05[eV]$ respectively), binding energy; $530{\pm}0.05[eV]$, optical energy band gap; 3.4[eV].

  • PDF

Evaluation of dose distribution from 12C ion in radiation therapy by FLUKA code

  • Soltani-Nabipour, Jamshid;Khorshidi, Abdollah;Shojai, Faezeh;Khorami, Khazar
    • Nuclear Engineering and Technology
    • /
    • 제52권10호
    • /
    • pp.2410-2414
    • /
    • 2020
  • Heavy ions have a high potential for destroying deep tumors that carry the highest dose at the peak of Bragg. The peak caused by a single-energy carbon beam is too narrow, which requires special measures for improvement. Here, carbon-12 (12C) ion with different energies has been used as a source for calculating the dose distribution in the water phantom, soft tissue and bone by the code of Monte Carlobased FLUKA code. By increasing the energy of the initial beam, the amount of absorbed dose at Bragg peak in all three targets decreased, but the trend for this reduction was less severe in bone. While the maximum absorbed dose per bone-mass unit in energy of 200 MeV/u was about 30% less than the maximum absorbed dose per unit mass of water or soft tissue, it was merely 2.4% less than soft tissue in 400 MeV/u. The simulation result showed a good agreement with experimental data at GSI Darmstadt facility of biophysics group by 0.15 cm average accuracy in Bragg peak positioning. From 200 to 400 MeV/u incident energy, the Bragg peak location increased about 18 cm in soft tissue. Correspondingly, the bone and soft tissue revealed a reduction dose ratio by 2.9 and 1.9. Induced neutrons did not contribute more than 1.8% to the total energy deposited in the water phantom. Also during 12C ion bombardment, secondary fragments showed 76% and 24% of primary 200 and 400 MeV/u, respectively, were present at the Bragg-peak position. The combined treatment of carbon ions with neutron or electron beams may be more effective in local dose delivery and also treating malignant tumors.

두 개 산소 가교형 몰리브덴(V)착물의 합성과 그 성질에 관한 연구 (Synthesis and Characterization of a $Di-{\mu}-oxo-bridged$ Molybdeum(V) Complexes)

  • 김일출;김영찬
    • 한국응용과학기술학회지
    • /
    • 제16권3호
    • /
    • pp.205-210
    • /
    • 1999
  • The Mo(V) $di-{\mu}-oxo$ type $[Mo_2O_4(H_2O)_2L]Cl_2$ complexes(L: 4,4'-Diphenyl-2,2'-dipyridyl, 4,4'-Dimethyl-2,2'-dipyridyl, 4,7-Diphenyl-1,10-phenanthroline) have been prepared by the reaction of $[Mo_2O_4(H_2O)_6]^{2+}$ with a series of chelate ligands. These complexes are completed by two terminal oxygens arranged trans to one another and each ligand forms a chelate types. In $Mo_2O_4(H_2O)_2L$ two $H_2O$ coordinated at trans site of terminal oxgens. The prepared complexes have been characterized by elemental analysis, infrared spectra, electronic spectra, $^1H$ nuclear magnetic resonance spectra, and thermal analysis(TG-DTA). In the potential range -0.00V to -1.00V at scan rate of $50mVs^{-1}$, a cathodic peak at -0.83V ${\sim}$ -0.88V (vs SCE) and an anodic peak at -0.54V ${\sim}$ -0.88V (vs SCE) have been observed in aquous solution. The ratio of the cathodic to anodic current(Ipc/Ipa) is almost 2, we infer that redox is irreversible as dimer forms broken.

양성자에 대한 금 나노입자의 밀도에 따른 흡수 에너지의 몬테카를로 전산모사 (Monte Carlo Simulation of Absorbed Energy by Gold Nano-Particles for Proton)

  • 천권수
    • 한국방사선학회논문지
    • /
    • 제18권1호
    • /
    • pp.1-9
    • /
    • 2024
  • 양성자 치료는 브래그 피크로 인해 우수한 치료 기법으로 알려져 있다. 양성자의 치료 효과를 높이기 위해 금 나노입자를 종양에 분포시켜 흡수선량을 높이는 방법이 연구되고 있다. 마이크로미터와 나노미터 범위에서 금 나노입자를 다루었던 것을 밀리미터 범위에서 금 나노입자를 전산모사 할 수 있는 방법을 제시하였다. 전산모사를 위해 Geant4 툴킷을 사용하였다. 인체와 유사한 물과 금 나노입자가 균일하게 분포되어 있다는 것을 가정하고 밀도비를 통해 금 나노입자의 개수 또는 농도를 조절하였다. 브래그 피크 위치에서 밀도비가 5%일 때 금 나노입자로 인해 순수 물 팬텀에 비해 흡수 에너지의 이득이 거의 2배로 나타났다. 밀도비가 증가할수록 흡수 에너지의 이득은 선형적으로 증가하였다. 브래그 피크 위치에서 금 나노입자가 하나의 복셀에만 분포하고 있을 때 양성자의 에너지는 자신 주변의 복셀에만 영향을 미치지만, 넓은 영역에 금 나노입자가 분포하는 경우 순수 물 팬텀에서 최고 흡수 에너지 (9.95 keV)의 95% 흡수 에너지 (9.46 keV)를 나타내는 부피는 16배 큰 영역에서 흡수 에너지의 이득이 나타났다. 그리고 이 영역은 밀도비가 증가할수록 증가하였다. 밀리미터 범위에서 금 나노입자의 밀도비와 RBE의 관계를 정량화하는 등 추가적인 연구가 필요하다.

Relationship between plasma asymmetric dimethylarginine and nitric oxide levels afects aerobic exercise training-induced reduction of arterial stifness in middle-aged and older adults

  • Shimomura, Mio;Fujie, Shumpei;Sanada, Kiyoshi;Kajimoto, Hiroki;Hamaoka, Takafumi;Iemitsu, Motoyuki
    • 운동영양학회지
    • /
    • 제25권1호
    • /
    • pp.16-22
    • /
    • 2021
  • [Purpose] Aerobic exercise training (AT) reverses aging-induced deterioration of arterial stiffness via increased arterial nitric oxide (NO) production. Asymmetric dimethylarginine (ADMA), an endogenous inhibitor of NO synthase, was decreased by AT. However, whether AT-induced changes in ADMA levels are related to changes in nitrite/nitrate (NOx) levels remains unclear. Accordingly, we aimed to clarify whether the relationship between plasma ADMA and NOx levels afected the AT-induced reduction of arterial stifness in middle-aged and older adults. [Methods] Thirty-one healthy middle-aged and older male and female subjects (66.4 ± 1.3 years) were randomly divided into two groups: exercise intervention and sedentary controls. Subjects in the training group completed an 8-week AT (60%-70% peak oxygen uptake [${\dot{V}}O_{2peak}$] for 45 min, 3 days/week). [Results] AT signifcantly increased ${\dot{V}}O_{2peak}$ (P < 0.05) and decreased carotid β-stifness (P < 0.01). Moreover, plasma ADMA levels were significantly decreased while plasma NOx levels and NOx/ADMA ratio were significantly increased by AT (P < 0.01). Additionally, no sex diferences in AT-induced changes of circulating ADMA and NOx levels, NOx/ADMA ratio, and carotid β-stifness were observed. Furthermore, the AT-induced increase in circulating ADMA levels was negatively correlated with an increase in circulating NOx levels (r = -0.414, P < 0.05), and the AT-induced increase in NOx/ADMA ratio was negatively correlated with a decrease in carotid β-stifness (r = -0.514, P < 0.01). [Conclusion] These results suggest that the increase in circulating NOx with reduction of ADMA elicited by AT is associated with a decrease in arterial stiffness regardless of sex in middle-aged and older adults.

Seismic base isolation of precast wall system using high damping rubber bearing

  • Tiong, Patrick L.Y.;Adnan, Azlan;Rahman, Ahmad B.A.;Mirasa, Abdul K.
    • Earthquakes and Structures
    • /
    • 제7권6호
    • /
    • pp.1141-1169
    • /
    • 2014
  • This study is aimed to investigate the seismic performance of low-rise precast wall system with base isolation. Three types of High Damping Rubber Bearing (HDRB) were designed to provide effective isolation period of 2.5 s for three different kinds of structure in terms of vertical loading. The real size HDRB was manufactured and tested to obtain the characteristic stiffness as well as damping ratio. In the vertical stiffness test, it was revealed that the HDRB was not an ideal selection to be used in isolating lightweight structure. Time history analysis using 33 real earthquake records classified with respective peak ground acceleration-to-velocity (a/v) ratio was performed for the remaining two types of HDRB with relatively higher vertical loading. HDRB was observed to show significant reduction in terms of base shear and floor acceleration demand in ground excitations having a/v ratio above $0.5g/ms^{-1}$, very much lower than the current classification of $0.8g/ms^{-1}$. In addition, this study also revealed that increasing the damping ratio of base isolation system did not guarantee better seismic performance particularly in isolation of lightweight structure or when the ground excitation was having lower a/v ratio.

EFFECTS OF MECHANICAL PROPERTY VARIABILITY IN LEAD RUBBER BEARINGS ON THE RESPONSE OF SEISMIC ISOLATION SYSTEM FOR DIFFERENT GROUND MOTIONS

  • Choun, Young-sun;Park, Junhee;Choi, In-Kil
    • Nuclear Engineering and Technology
    • /
    • 제46권5호
    • /
    • pp.605-618
    • /
    • 2014
  • The effects of variability of the mechanical properties of lead rubber bearings on the response of a seismic isolation system are investigated. Material variability in manufacturing, aging, and operation temperature is assumed, and two variation models of an isolation system are considered. To evaluate the effect of ground motion characteristics on the response, 27 earthquake record sets with different peak A/V ratios were selected, and three components of ground motions were used for a seismic response analysis. The response in an isolation system and a superstructure increases significantly for ground motions with low A/V ratios. The variation in the mechanical properties of isolators results in a significant influence on the shear strains of the isolators and the acceleration response of the superstructure. The variation provisions in the ASCE-4 are reasonable, but more strict variation limits should be given to isolation systems subjected to ground motions having low A/V ratios. For application of seismic isolation systems to safety-related nuclear structures, the variation in the material and mechanical properties of the isolation system should be properly controlled during the manufacturing and aging processes. In addition, special consideration should be given to minimize the accidental torsion caused by the dissimilarity in the stiffness variations of the isolators.

선형 저밀도 폴리에틸렌과 에틸렌 비닐아세테이트의 혼합비에 따른 박막의 전기적 특성 (The Electrical Properties of Film due to the Mixture Ratio of Linear Lour Density Polyethylene and Ethylene Vinyl Acetate)

  • 이충호;박찬원
    • 한국안전학회지
    • /
    • 제14권2호
    • /
    • pp.83-89
    • /
    • 1999
  • The electrical properties due to mixture ratio of linear low density polyethylene(LLDPE) and ethylene vinyl acetate(EVA) films are studied. An experimental specimen is selected as LLDPE/EVA of thickness 200${\mu}{\textrm}{m}$ produced by mixture ratio of 50 : 50, 60 : 40, 70 : 30 and 80 : 2 wt%. In temperature range from $25^{\circ}C$ to 12$0^{\circ}C$, the measurement of volume resistivity using a highmegohm meter is performed within 10 minutes since each voltage of DC 100 V, 250 V, 500 V and 1000 V is applied, according to the step voltage method. From FT-IR spectrum for an analysis of physical properties, it can be confirmed that LLDPE blended with EVA shows an absence of carbonyl groups(1735 $cm^{-1}$, C=0) and ether groups(1242 $cm^{-1}$, C-O). The peak of LLDPE and EVA made of mixture ratio of 70 : 30 at 2$\theta$ =21.4$^{\circ}$ in the results of XRD is higher than the others. In the experiment for volume resistivity characteristics in order to investigate the electrical properties of specimen, it is confirmed that volume resistivity is decreased with the increase of the molecular motion and temperature.

  • PDF

Analysis and Design of a Multi-resonant Converter with a Wide Output Voltage Range for EV Charger Applications

  • Sun, Wenjin;Jin, Xiang;Zhang, Li;Hu, Haibing;Xing, Yan
    • Journal of Power Electronics
    • /
    • 제17권4호
    • /
    • pp.849-859
    • /
    • 2017
  • This paper illustrates the analysis and design of a multi-resonant converter applied to an electric vehicle (EV) charger. Thanks to the notch resonant characteristic, the multi-resonant converter achieve soft switching and operate with a narrowed switching frequency range even with a wide output voltage range. These advantages make it suitable for battery charging applications. With two more resonant elements, the design of the chosen converter is more complex than the conventional LLC resonant converter. However, there is not a distinct design outline for the multi-resonant converters in existing articles. According to the analysis in this paper, the normalized notch frequency $f_{r2n}$ and the second series resonant frequency $f_{r3n}$ are more sensitive to the notch capacitor ratio q than the notch inductor ratio k. Then resonant capacitors should be well-designed before the other resonant elements. The peak gain of the converter depends mainly on the magnetizing inductor ratio $L_n$ and the normalized load Q. And it requires a smaller $L_n$ and Q to provide a sufficient voltage gain $M_{max}$ at ($V_{o\_max}$, $P_{o\_max}$). However, the primary current increases with $(L_nQ)^{-1}$, and results in a low efficiency. Then a detailed design procedure for the multi-resonant converter has been provided. A 3.3kW prototype with an output voltage range of 50V to 500V dc and a peak efficiency of 97.3 % is built to verify the design and effectiveness of the converter.

Determination of Total Phenols in Environmental Waters by Capillary-HPLC with U.S.E.P.A. Classified Eleven Priority Pollutant Phenols after Nitrosation and Their Visible Spectrophotometric Detection

  • Chung, Yong-Soon
    • Bulletin of the Korean Chemical Society
    • /
    • 제26권2호
    • /
    • pp.297-302
    • /
    • 2005
  • The determination of total phenols was accomplished by capillary-high performance liquid chromatography (capillary-HPLC) after nitrosation of the U.S.E.P.A. classified 11 priority pollutant phenols, using the nitrosated parent phenol (POHNO) as a reference for calibration. The optimum mobile phase composition for this analysis was found by examining the effect of changing the percentage of acetonitrile (MeCN) in the mobile phase on retention factors (k values) and peak intensities. As MeCN percentage was increased, k values were reduced and peak intensities were generally increased. From the results obtained, it was found that the optimum mobile phase was 90%(v/v) MeCN solution at pH 8.0, the detection wavelength of 400 nm, and a detection limit (D.L., concentration at signal to noise ratio (S/N) of 3.0) of 4.5 ${\times}$ $10^{-7}$ M. In addition, 10 of the 11 phenols present in mineral or waste water were separated after the nitrosation by capillary-HPLC. The optimum mobile phase for separation was a 40%(v/v) MeCN solution at pH 5.0.