• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 1998년도 제11회 학술강연회논문집
• /
• pp.7-7
• /
• 1998

액체 연료 분포의 균일성과 대칭성은 연소 효율을 높이고, 공해 물질을 줄이는데 있어서 필수적인 요소이기 때문에 분무 패턴을 정량적으로 해석하는 것은 매우 중요하다. 고전적으로 사용되고 있는 mechanical patternator는 ⅰ) 유동을 교란시키고, ⅱ) 공간 분해능이 떨어지며, ⅲ) 복잡한 재순환 유동이나 화학 반응이 있는 유동에서의 적용이 어렵다는 단점을 가지고 있다. 이러한 단점들을 극복하기 위하여 레이저를 이용한 optical patternator에 대한 연구가 진행되고 있다. Optical patternator는 유동을 교란시키지 않으면서 고해상도의 분무 패턴 측정을 할 수 있다. 형광 신호는 물질의 체적에 비례한다. 따라서, 레이저 평면광을 분무에 조사시켜 주어서 유도되는 형광 신호를 이용하는 평면액체 레이저 유도 형광법(PLLIF : Planar Liquid Laser Induced Fluorescence)은 분무패턴을 알아보는 매우 유용한 방법이다.

• 한국분무공학회지
• /
• 제4권4호
• /
• pp.9-16
• /
• 1999

Spray angle, a parameter which is most commonly used to evaluate. spray distribution, is important because it affects the axial and radial distribution of the fuel. Spray angles were measured and compared for the pintle-type gasoline fuel injector with n-heptane as a test fuel with the three different measuring techniques, i.e. digital image processing, shadowgraphy and spray patternator, respectively. Fuel was injected with the injection pressures of 0.2-0.35MPa into the room temperature and atmospheric pressure environment. In digital image processing method, the transmittance level greatly influences the spray angle with the axial distance from the injector. From the experimental results by the shadowgraphy technique, it is obvious that the spray angle vary during the injection period. The results of spray angle from the spray patternator show that there exist the different spray angles in the different areas. The spray angles increase with the increase in the injection pressure for the three measurement techniques considered in this study. The spray angle is widely different, especially in the near region from the injector, according to the measurement techniques used in this experimental work.

• 한국분무공학회지
• /
• 제11권4호
• /
• pp.205-211
• /
• 2006

Impinging angle, impinging distance, length eve. diameter and injection pressure of a triplet injector were tested to evaluate the spray characteristics injected by liquid/gas combinations. Two different kinds of unlike triplet sprays were produced by changing the gas and liquid feed lines. One was the G-L-G(Gas-Liquid-Gas) type, and the other was L-G-L(Liquid-Gas-Liquid) type. Spray angles were wider with the G-L-G type than with L-G-L type. Mass distributions in spray were obtained with a, mechanical patternator. Mass distributions were not circular but elliptical distributions. When the range of mechanical patternator to injector decreased, mass distributions were more concentrated in the center region.

• 한국가시화정보학회지
• /
• 제3권1호
• /
• pp.63-70
• /
• 2005

Optical Line Patternator(OLP) has been applied to get a distribution of the spray at high ambient pressure. OLP is a combined technique of extinction measurement and image processing. The attenuated intensity of laser beam after traversing spray region was measured by using a photo-detector, and the line image of Mie-scattering was captured simultaneously in the path of each laser beam by using a CCD camera. The distribution of extinction coefficient in the spray is obtained by processing these data with the algebraic reconstruction technique. From the distribution of extinction coefficient, the surface distribution of spray can be reconstructed. OLP does not use laser sheet but use laser beam so that the noise effect of multiple scattering, caused by increasing number density of droplet in high pressure environment, is reduced drastically. OLP is expected as a suitable method which can investigate the characteristics of relatively large spray under the high pressure environment such as liquid rocket engine.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.283-286
• /
• 2002

The mixing of fuel and oxidizer and each mass distribution of unlike split triplet(F-O-O-F) injector for liquid rocket which are known to affect the combustion efficiency significantly, has been investigated using PLLIF technique. Experiment is conducted to investigate the effect of mixture ratio(MiR), momentum ratio(MoR) and impinging angle on mixing efficiency. The mixing efficiency, which is introduced by Rupe, gives the global chracteristic of spray mixing. Experiment far comparison with triplet injector(F-O-F), which has same momentum ratio and impinging angle with split triplet injector is conducted.

• 한국가시화정보학회지
• /
• 제19권1호
• /
• pp.43-49
• /
• 2021

In this experimental study, measurement techniques such as backlight imaging, optical patternator, and laser sheet drop sizing were applied to characterize open-type swirl injector used in Russian liquid rocket engine, RD 107. The typical development of swirl spray was observed in backlight images. The breakup length was measured by using the ratio between Mie scattering and fluorescence signal. Relative Sauter Mean Diameter was measured by using laser sheet drop sizing and the possible source of errors were discussed.

• 한국항공우주학회지
• /
• 제33권1호
• /
• pp.54-61
• /
• 2005

기체와 액체 추진제를 사용하는 동축형 분사기의 분무특성을 조사하기 위하여 shadow graph와 mechanical patternator, PDPA를 이용한 실험을 수행하였다. 차원해석 방법을 도입하여 운동량 플럭스 비(M)와 레이놀즈 수(Re)를 기체/액체 동축형 분무의 주요 변수로 설정하였고, 실험을 통하여 전단 및 스월 동축형 분무의 특성을 거시적 및 미시적 관점에서 비교분석하였는데, 기체 추진제의 영향력이 커지는 분사조건에서 전단 및 스월 동축형 분무의 거시적 특성이 유사해짐을 확인할 수 있었다. 또한, 본 연구에서는 미시적 분무특성에 대한 분석 결과로서 분무액적 크기와 분사조건 사이의 관계식도 제시하였다.

• 한국분무공학회지
• /
• 제5권3호
• /
• pp.17-26
• /
• 2000

The main parameter commonly used to evaluate spray distribution is spray angle. Spray angle is important because it influences the axial and radial distribution of the fuel. Spray angles were measured and compared for the two non-air assisted injectors such as 2hole-2stream 4hole-1stream injectors used for port fuel injection gasoline engines with n-heptane as a fuel by three different measuring techniques, i.e., digital image processing, shadowgraphy, and spray patternator, respectively. Fuel was injected with the injection pressures of 0.2-0.35 MPa into the room temperature and atmospheric pressure environment. In digital image processing approach, the selection of the transmittance level is critical to obtain the edge of spray and hence to measure the spray angle. From the measurement results by the shadowgraphy technique, it is dear that the spray angle is varied during the spray injection period. The measurement results from spray patternator show that the different spray angles exist in different region. Spray angle increases with the increase in the injection pressure. it is suggested that the spray angle and stream separated angle should be specified when spray is characterized for 2hole-2stream injector, because spray angle is much different though stream separated angle is same. It was also considerably affected by the measurement techniques introduced in this experimental work. However, the optimal axial distance for measuring the spray angle seems to be at least 60-80 mm from the injector tip for two non-air assisted injectors.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.637-642
• /
• 2017

본 연구에서는 우주발사체의 터빈배기구 열교환기의 입구조건을 모사하는 고온고압 증기 발생장치의 개발을 위해 설계/제작한 엔진 헤드와 구축한 설비를 검증하는 내용을 담고 있다. 단일 분사기를 설계/제작하여 수류시험을 진행했으며, 이를 통해 각 단일 분사기당 설계유량이 공급되는 차압을 확인하고, 분무형태를 patternator를 통해 확인했다. 이를 바탕으로 선정한 분사기로 엔진 헤드를 제작했으며 수류시험과 실추진제 분무시험이 진행됐다. 연소시험을 통해 유량, 압력, 연소효율 등에 대해 분석했으며 이를 통해 고온고압 증기 발생장치 개발을 위한 엔진 헤드 검증을 마쳤다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.877-880
• /
• 2011

기체메탄/액체산소를 추진제로 사용하는 동축 스월/전단형 인젝터를 설계 및 제작하였다. 각 추진제의 오리피스 개수와 유입오리피스 후단의 형상 등은 상용 해석프로그램인 Fluent를 이용하여 유동해석을 수행한 결과를 바탕으로 결정하였다. 설계/제작된 인젝터는 수류시험을 통해 차압에 따른 설계유량을 측정하였고, 패터네이터를 이용하여 유량분포의 균일성을 확인하였다. 측정결과 설계 유량의 약10% 내외의 차이를 보였으며, 산화제 인젝터의 분무각은 $66^{\circ}$로 측정되었다.