• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.4
• /
• pp.105-111
• /
• 2019

In this paper, a performance analysis of waveguide broad-wall slot array antenna for millimeter-wave seeker in Ka-band was performed as using near-field measurement. The measurement of slot array antenna was conducted in both far-field and near-field. And the validation of near-field test in millimeter band was confirmed. It was confirmed that the beam pattern characteristics including beam width and side lobe level of the slot array antenna that performed the verification were the same. Differenced in the side lobe level of azimuth and elevation beam pattern were verified to be less than 1dB. Additionally, the new antenna aperture distribution was extracted as using back-projection method modifying the near-field data and then introduced the method conducting performance analysis of array antenna.

• Journal of IKEEE
• /
• v.27 no.4
• /
• pp.636-643
• /
• 2023

In this paper, a high-speed calibration method for phased array antennas in the far-field is presented A max calibration, which is a simplification of the rotating-element electric-field vector (REV) method that calibrates each antenna element only through received power, and a method of grouping calibrations by sub-array unit rather than each antenna element were proposed. Using the Proximal Policy Optimization (PPO) algorithm, we found a partitioning optimized for the distribution of phased array antennas and calibrated it on a subarray basis. An adaptive max calibration method that allows faster calibration than the conventional method was proposed and verified through simulation. Not only is the gain of the phased array antenna higher while calibration is being made to the target, but the beam pattern is closer to the ideal beam pattern than the conventional method.

• The Journal of the Acoustical Society of Korea
• /
• v.20 no.5
• /
• pp.110-115
• /
• 2001

In this paper, we propose a beamformer adequate for the nested away that is generally used for multiple frequency band signal processing. The nonisotropic beam pattern of channel in this array causes two problems: the bearing-estimate error of mainlobe and the difference between design and output in sidelobe level. By separating the time delay among channel signals and the time delay among sensor signals in channel, we can remove the effects of the nonisotropic beam pattern of channel in the beamformer output. Through this process, a method to correct simultaneously these problems is proposed.

• Journal of Sensor Science and Technology
• /
• v.22 no.4
• /
• pp.286-291
• /
• 2013

This paper presents to analyze patterns from single and complex malodors using gas sensor array based on metal oxide semiconductors. The aim of research is to identify and discriminate single malodors such as $NH_3$, $CH_3SH$ and $H_2S$ and their mixtures according to concentration levels. Measurement system for analyzing patterns from malodors is constructed by an array of metal oxide semiconductor sensors which are available commercially together with associate electronics. The patterns from sensory system are analyzed by Principal Component Analysis (PCA) which is simple statistical pattern recognition technique. Throughout the experimental trails, we confirmed the experimental procedure for measurement system such as sensors calibration time and gas flow rate, and discriminated malodors using pattern analysis technique.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.10
• /
• pp.1434-1440
• /
• 2014

This paper describes a demosaicking method for hexagonally-structured color filter array. Demosaicking is essential to acquire color images using color filter array (CFA) in single sensor imaging. Thus, CFA patterns have been discussed in order to improve image quality in single sensor imaging after the Bayer pattern are introduced. Advancements in imaging sensor technology recently introduce a hexagonal CFA pattern. The hexagonal CFA can be considered to be a 45-degree rotational version of the Bayer pattern, thus demosaicking can be implemented by an existing method with backward and forward 45-degree rotations. However, this approach requires heavy computing power and memory in image sensing devices because of the image rotations. To overcome this problem, we proposes a demosaicking method for a hexagonal Bayer CFA without rotations. In addition, we introduce a weighting parameter in our demosaicking method to improve image quality and to unifying exiting method with our method. Experimental results indicate that the proposed method is superior to conventional methods in terms of PSNR. In addition, some optimized values for the weighting parameter are provided experimentally.

• Journal of IKEEE
• /
• v.24 no.2
• /
• pp.626-631
• /
• 2020

In this paper, a study on beam synthesis technique of conformal array was performed. It is applied to various radar systems that can perform beam steering without deterioration of performance due to beam steering in a general linear arrangement. Unlike the beam synthesis technique in the planar linear array, the conformal array has a radiation element located on a curved surface, so it is necessary to compensate for a difference in length from the radaation element to the wave front surface. In addition, by calculating the offset angle for each radiation element and applying it during actual synthesis, it was possible to predict an accurate beam pattern. In this paper, length compensation and offset angle were calculated and applied to beam pattern synthesis to perform beam pattern comparison, and performance was compared through mathematical analysis.

• Proceedings of the KIEE Conference
• /
• 1987.07b
• /
• pp.1121-1124
• /
• 1987

Previous methods to map from a FORTRAN-like specification into a systolic array were difficult to find data dependencies because the specification was expressed and executed sequentially. Data-flow graph(DFG)s show data dependencies explicitly. In this paper we show a mapping tool from a DFG specification into a systolic array. We introduce the concept of a Systolic Pattern Stream(SPS) and use that concept to derive a systolic array.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.147-150
• /
• 1999

A T-shaped microstripline-fed printed slot array antenna having wide bandwidth, high gain, and narrow bandwidth is presented in this paper. The proposed antenna is analyzed by using the transmission line model method. We fabricated 4$\times$1 microstrip slot array antenna and measured its return loss and radiation pattern. The maximum bandwidth of this array antenna is from 1.43 ㎓ to 2.60 ㎓, which is 58.1% for the VSWR $\leq$ 2.

• Journal of KSNVE
• /
• v.8 no.4
• /
• pp.663-669
• /
• 1998

In this paper, a beam design method is presented for the planar array with unequal transducer sensitivities. Basically the proposed method consists of two steps. At first, the optimum weightings are designed with the assumption that all array elements have an uniform sensitivity. Next, the compesnated weightings for the unequal transducer sensitivities can reversely be determined from an inverse problem utilizing the design beam pattern evaluated by the predetermined optimal weightings. A numerical example is inculded to illustrate the proposed method.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.1
• /
• pp.59-65
• /
• 2000

This paper describes the characteristics of a one dimensional narrow-wall slotted waveguide array with a single-layer linear-to-circular polarization converter consisting of a dipole array. An external boundary value Problem of one slot and three dipoles, which approximates the mutual coupling between the dipole array and an edge slot extending over three faces of a rectangular waveguide, is formulated and analyzed by the method of moments; design of polarization conversion is conducted for this model as a unit element. If every unit element has perfect circular polarization, grating lobes appear in the array pattern due to the alternating slot angle: these are suppressed in this paper by changing the dipole angle and degrading the axial ratio of the unit element. The validity of the design is confirmed by the measurements. The dipole array has negligible effects upon slot impedance; the polarization conversion for existing narrow-wall slotted arrays is realized by add-on dipole array.