• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.91-96
• /
• 2002

This study is to analyze the influence of paste flow, compaction time and compaction thickness on the fundamental properties of porous concrete. Results of this study were shown as follows; 1) As paste flow increase, compaction time according to paste flow and compaction thickness decrease. Also, though paste flow is same, as compaction thickness increase, compaction time Increase. So It must be considered that the influence of compaction time according to paste flow and compaction thickness. 2) In the range of this study, compressive strength is the highest value at paste flow 190mm. 3) Occasion of manufactured compactor in this study compaction thickness 10, 15cm is influenced heavily but compaction thickness 20cm is influenced slightly.

• Computers and Concrete
• /
• v.10 no.1
• /
• pp.35-47
• /
• 2012

The ideal gradating curve is used in this study to estimate densified aggregate blended ratio and total surface area of aggregate, there by under assigned paste amount of concrete, and coating paste thickness can then be deduced. Four groups of concrete mixtures were prepared and the corresponding concrete properties, such as workability, compression strength, ultrasonic velocity, surface resistivity and chloride ion penetration, were measured and finally the results are interpreted in terms of "coating thickness". The result shows as the coating thickness of the concrete is higher than critical one, the coating thickness on aggregate does affect the workability, and whatever workability is required the superplasticizer can be adjusted to achieve the demand workability. Under a fixed paste quality at the same age, coating paste thickness is inversely proportional to the concrete properties, especially as the coating thickness gets thinner.

• Computers and Concrete
• /
• v.10 no.1
• /
• pp.19-33
• /
• 2012

The performance of a concrete is significantly influenced by its mixture proportion and the coating thickness on aggregate surface. The concrete in this study is designed by estimating the blending ratio of aggregate using a densified mixture design algorithm (DMDA) based on an ideal grading curve and estimating the paste volume as the sum of the amount of paste needed to provide an assigned coating paste thickness. So as to obtain appropriate concrete amount, and thus can accurately estimate the property of concrete. Deduction of this mix design formula is simple and easy understanding, and meanwhile to obtain result is fast. This estimation model of mix design is expected to reward to industry and effectively upgrade concrete quality.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.5
• /
• pp.23-29
• /
• 2019

This study applies to the surface modification technique by coating the surface of aggregates using the modified paste such as cementitious materials in order to develop completely recycling technology of coarse aggregate. In this case, coating thickness of modified aggregate can be considered that the decision is dependent on the viscosity and tenacity of modified paste. In this study identify the flow properties of the fresh modified paste, and examined for the coating thickness of modified aggregate. As a result, it was possible to design a quantitative coating thickness of modified paste assuming that a modified paste to a Bingham Fluid and consider by excess paste theory and rheology constant (yield value). Accordingly, it is considered that the quantitative mix design of concrete using by surface modified aggregates will be possible.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.9
• /
• pp.827-832
• /
• 2005

Dual band internal antennas were fabricated with Ag conducting paste of various preparation conditions and different print thickness by silk screen print. We have investigated microwave properties were compared Ag conducting paste antenna with copperplate antenna at 800 MHz and 1,800 MHz. Gain of Ag conducting paste antenna was improved when preparation conditions were the single size Ag particle, using dry type resin and high Ag containing percent. However, it was lower than that of copperplate antenna within $0.1\~2.0dBi$ at 800MHz. In addition, it was improved at 800MHz when thickness of Ag conducting paste was printed more than skin depth but it was held after critical print thickness. On the other hand, it was reached level of copperplate antenna at 1,800MHz.

• Korean Journal of Materials Research
• /
• v.25 no.1
• /
• pp.16-20
• /
• 2015

In this study, in order to improve the efficiency of n-type monocrystalline solar cells with an Alu-cell structure, we investigate the effect of the amount of Al paste in thin n-type monocrystalline wafers with thicknesses of $120{\mu}m$, $130{\mu}m$, $140{\mu}m$. Formation of the Al doped $p^+$ layer and wafer bowing occurred from the formation process of the Al back electrode was analyzed. Changing the amount of Al paste increased the thickness of the Al doped $p^+$ layer, and sheet resistivity decreased; however, wafer bowing increased due to the thermal expansion coefficient between the Al paste and the c-Si wafer. With the application of $5.34mg/cm^2$ of Al paste, wafer bowing in a thickness of $140{\mu}m$ reached a maximum of 2.9 mm and wafer bowing in a thickness of $120{\mu}m$ reached a maximum of 4 mm. The study's results suggest that when considering uniformity and thickness of an Al doped $p^+$ layer, sheet resistivity, and wafer bowing, the appropriate amount of Al paste for formation of the Al back electrode is $4.72mg/cm^2$ in a wafer with a thickness of $120{\mu}m$.

• Computers and Concrete
• /
• v.8 no.2
• /
• pp.163-176
• /
• 2011

By virtue of chord-length density function from the field of statistical physics, this paper introduced a quantitative approach to estimate the distribution of cement paste thickness between aggregates in concrete. Dynamics mixing method based on molecular dynamics was employed to generate one model structure, then image analysis algorithm was used to obtain the distribution of thickness of cement paste in model structure for the purpose of verification. By comparison of probability density curves and cumulative probability curves of the cement paste thickness among neighboring aggregates, it is found that the theoretical results are consistent with the simulation. Furthermore, for the model mortar and concrete mixtures with practical volume fraction of Fuller-type aggregate, this analytical formula was employed to predict the influence of aggregate volume fraction and aggregate fineness. And evolution of its mean values were also investigated with the variation of volume fraction of aggregate as well as the fineness of aggregates in model mortars and concretes.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.31 no.6
• /
• pp.282-286
• /
• 2021

Penetration depth and compressive residual stress of laser-carburized TiZrN coating by thickness of carbon paste were investigated in terms of carbon potential. The carbon paste was covered with a thickness of 1.1 mm using screen printing, and applied to a thickness of 0.4 mm using spin coating, and laser carburization was performed under the same conditions. As the thickness of carbon paste increased, the diffraction pattern of the laser-carburized TiZrN coating shifted to a lower angle, indicating solid solution strengthening and lattice distortion. For microstructure analysis using TEM, the defects and carbon concentration of the laser-carburized TiZrN coating increased as the carbon paste was thicker. It indicated that the variation of the carbon potential corresponds to the change in the paste thickness. In XPS depth profile analysis, high concentration of carbon and formation of carbide were observed in laser-carburized TiZrN coating with thick carbon paste. It revealed that the carbon concentration on the surface and carbon potential were changed by the thickness control of carbon paste. The compressive residual stress increased from 3.67 GPa to 4.58 GPa by the variation of carbon concentration.

• Journal of the Korean Ceramic Society
• /
• v.30 no.5
• /
• pp.347-356
• /
• 1993

In joining alumina ceramics to metal by using Mo-Mn metallizing process the effects of metallizing thickness, temperature, and the composition of paste on the bond strength and the microstructure of joining interface were investigated. The bond strength variation in the range of metallizing temperature, 1350~155$0^{\circ}C$ was more than 150MPa above 145$0^{\circ}C$ and the optimum metallizing thickness was 30${\mu}{\textrm}{m}$. The optimum contents of Mn in Mo-Mn paste was 5% due to the bond strength decrease with the increase of addition. The effect of SiO2 addition in paste on bond strength was saturated around 200MPa. It was also observed that as the particle size of Mo decreased, the joinning with higher bond strength was shown in spite of low metallizing temperature.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1379-1381
• /
• 1998

Powder electroluminescent device (PELD) structured conventionally dielectric and phosphor layer, between electrode and their layer fabricated by screen printing splaying or spin coating method. To promote performance of PELDs, we approached the experiments for different structure and thickness variation of PELD. Thickness variation($30{\mu}m{\sim}130{\mu}m$) was taken. To investigate electrical and optical properties of PELDs, EL spectrum, transferred charge density using Sawyer-Tower's circuit brightness was measured. Variation of structure in PELDs was as follows: WK-1 (ITO/BaTiO3/ZnS:Cu/Silver paste), WK-2 (ITO/BaTiO3/ZnS:Cu/BaTiO3/ZnS:Silver paste), WK-3 (ITO/BaTiO3/ZnS:Cu/BaTiO3/Silver paste), WK-4(ITO/BaTiO3+ZnS:Cu/Silver paste) As a result, structure of the highest brightness appeared WK-4 possessed 60 ${\mu}m$ thickness. The brightness was 2719 cd/$m^2$ at 100V, 400Hz.