• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.1
• /
• pp.74-80
• /
• 2021

When a berth is built close to a fairway, a moored vessel will be affected by the ship waves generated by navigating vessels. In this study, a portable measurement system was developed to measure the roll motion of an actual vessel, and the results were compared with simulation results. The simulation results showed that the roll motion satisfies the loading safety criteria. However, the actual results of the vessel, did not satisfy the criteria in some cases. In this study, 18 cases that did not satisfy the loading safety criteria were analyzed. Among these cases, three cases were affected by a different time zone of the remaining 15 cases, 11 cases (73.3%) were observed to be consistent with arrival times of passenger ships of more than 10,000GT sailing between in Mokpo and Jeju. The results of this study can be used to reflect marine traffic characteristics in the assessment of loading safety, which can increase the reliability of results of the loading safety assessment of ships.

• Journal of Applied Reliability
• /
• v.12 no.2
• /
• pp.79-90
• /
• 2012

The torsion beam type of rear suspension has been adopted by most manufactures of small to medium front wheel drive passenger cars. Previous studies analyzed only the load characteristics of CTBA(the coupled torsion beam axle)'s components. This paper analyzed the results of measurement after measuring loads and displacements, angles when a car equipped with the coupled torsion beam axle is driving in various roads. The most important durability factors for CTBA part are the force and direction of rear CTBA trailing arm. If there are design changes, it was difficult to make a sensor and install each time for measuring the trailing arm forces. After analyzing the loading histories between body and chassis, we developed the transformation matrix that can be converted to mutual force. This paper also deals with the analysis of the force behavior through the analysis of the influence and correlation between the body and chassis parts of cars.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.413-414
• /
• 2002

An automotive wheel bearing is one of the most important components to guarantee the service life of a passenger car. The endurance life of a bearing is affected by many parameters such as material properties, heat treatment, lubrication conditions temperature loading conditions, bearing geometry, internal clearance and so on. In this paper, we calculate the endurance life of wheel bearing units and analyze the sensitivity of bearing geometric parameters on the life by using Taguchi method.

• Journal of Auto-vehicle Safety Association
• /
• v.3 no.2
• /
• pp.11-16
• /
• 2011

In recent years, rapid-increasing market share of compact cars and SUVs has brought for both consumer and automaker to pay more attention on crash compatibility between the compact passenger vehicles and the light trucks (i.e., Pickups and SUVs). Vehicle compatibility regarding both self and partner protection in frontal crash of different class vehicles is one of hot issues in vehicle safety. Furthermore, it is expected that the amendment of UNECE-Regulation 94 to implement compatibility issues in couple of coming years. In this study, conceptual design of compatibility compliant frontal vehicle structure which subjects to improve? the distribution of frontal crash loading and structural engagement between vehicles is introduced. The effects of proposed vehicle structure on both possible candidates (i.e. FWRB, FWDB and PDB) for a compatibility evaluation test procedure and car-to-car crash are also investigated.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.162-167
• /
• 2002

An automotive wheel bearing is one of the most important components to guarantee the service life of a passenger car. The endurance life of a bearing is affected by many parameters such as material properties, heat treatment, lubrication conditions, temperature, loading conditions, bearing geometry, internal clearance and so on. In this paper, we analyze the relation between loads and deformations of wheel bearing units. On the basis of it, we calculate the endurance life of wheel bearing units and suggest a method to determine the initial contact angle to achieve a maximum endurance life with considering stress concentration.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.670-673
• /
• 2002

Automotive wheel bearings are one of the most important components to guarantee the service life of a passenger car. The endurance life of a bearing is affected by many parameters such as material properties, heat treatment, lubrication conditions, temperature, loading conditions, bearing geometry, internal clearance and so on. In this paper, we analyze the relation between loads and deformations of wheel bearing units. On the basis of it we calculate the endurance life of wheel bearing units and analyze the contribution of bearing geometric parameters on the endurance life by using Taguchi method.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.5
• /
• pp.160-164
• /
• 2007

An automotive wheel bearing is one of the most important components to guarantee the service life of a passenger car. The endurance life of a bearing is affected by many parameters such as material properties, heat treatment, lubrication conditions, temperature, loading conditions, bearing geometry, internal clearance and so on. Generally, a tapered roller bearing gives longer endurance life than that of an equivalent size ball bearing. Consequently, the application of taper bearing units will be increased for more compact design and extended warranty. In this paper, we derive the relation between loads and deformations of a taper bearing unit. On the basis of that, we calculate the endurance life of the taper bearing unit considering initial axial clearance.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.62 no.3
• /
• pp.127-132
• /
• 2013

In order to check traction of the elevator, the load-test is positively necessary on the inspection of elevator in Korea. So actual loads are used in the elevator car for the load-test. However, some of advanced countries in Europe, for example Germany, are using the alternative method with no load test instead of traditional load-test. Commonly hydraulic elevator, compared to passenger elevator is mainly used for loading heavy weights. It requires a great deal of labor to carry out load-test. The reason is why we developed a new inspection skill for the load-test of hydraulic elevator without actual loads. The results of studies show that the new method of the load-test can be replace the traditional load-test.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.23 no.3
• /
• pp.81-87
• /
• 2015

Load master is authorized to be controlled all of loading stuffs for safety of flight such as passenger, baggage, cargo and e.t.c. There are many things are missed even though the weight and balance is the most important process. This study analyzes how the differences of C.G. by among ten load masters of each careers. This study is tested how load-master takes load-control by the respective result based on differences of each practical experiences, gender and a number of certification. In result, all of load masters set C.G. on the stability region. But the practical experience of load master is relative to set better C.G. for economical effectiveness of weight and balance control work.

• Proceedings of the KSR Conference
• /
• 2004.06a
• /
• pp.199-205
• /
• 2004

This paper describes the result of structure analysis and load test of bogie frame. The purpose of the analysis and test is to evaluate an safety which bogie frame shall be considered fully sufficient rigidity so as to satisfy proper system function under maximum load. Bogie system consist of bogie frame, suspensions, wheel-sets, brake system and transmission system. Among these component, the bogie frame is most significant component subjected to the vehicle and passenger loads. The evaluation method is used the JIS E 4207 specification throughout the FEM analysis and static load test. The test results have been very safety and stable for design load conditions.