• 한국생산제조학회지
• /
• 제20권3호
• /
• pp.280-283
• /
• 2011

This study investigates the durability of car body and the safety of passenger inside car body in the case of the impact contact at passenger and car body. In case of front impact contact, maximum von Mises equivalent stress and principal stress become 3240.7MPa and 1634MPa respectively at the rear part of car body and the neck of dummy. And maximum total deformation occurred with 14.145mm at the hand of dummy. In case of side impact contact, maximum von Mises equivalent stress and principal stress become 7687.9MPa and 1690.7MPa respectively at the front part of car body and the lap of dummy. And maximum total deformation occurred with 16.414 mm at the foot of dummy. In case of rear impact contact, maximum von Mises equivalent stress and principal stress become 2366.6MPa and 1447MPa respectively at the front part of car body and the neck of dummy. And maximum total deformation occurred with 7.548mm at the rear part of car body. As the maximum von-Mises stress at side impact is shown with more than 700MPa as over two times at front or rear impact the danger of car body is increased. The great possibility of damage is shown at neck and hand of dummy with more than total displacement of 10mm.

• 대한교통학회지
• /
• 제9권2호
• /
• pp.5-26
• /
• 1991

Concepts of passenger car equivalent(PCE) based on various philosophies is reviewed. The headway method is redefined in two ways namely a macroscopic headway method and a microscopic headway method of which the concepts are confused in literature. As definition of the microscopic headway method is from intuitive approach so theoretical basis for this method is explained in connection with the macroscopic headway method. In addition new classification and evaluation of complicated existing theories was conducted to make the reader understand more easily.

• 한국생산제조학회지
• /
• 제18권5호
• /
• pp.477-482
• /
• 2009

This study analyzes the result with dynamic simulation about deformation according to time when a car impacts bollard. These results are shown as followings. The maximum deformation is shown at the lower part of front grass in case of the impact of front or passenger seat but this deformation is shown at the lower part of rear bumper in case of double impact. The maximum equivalent stress is shown at the upper part by the side grass of driver seat at the elapsed time of 0.00075 second after impact in case of the impact of front or passenger seat but this deformation is shown at the front bonnet at the elapsed time of 0.004 second after the additional impact in case of double impact. The maximum total deformation or equivalent stress is shown nearly same in case of the impact of front or passenger seat. But the value of this deformation or equivalent stress in case of the impact of front or passenger seat is shown with 2 times or more than 17% respectively as this value in case of double impact.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1499-1504
• /
• 2007

Spot-welding is widely used to construct passenger car bodies in automotive industry. Occasionally severe spot-weld distortions in sub-assembly make further spot-weld difficult. In this paper, distortions for various spot-weld conditions are measured using coordinate measuring machine. Then, based on finite element solution for unit translation or unit rotation of nugget edge, equivalent loads for spot-weld distortions are determined. They can be used to predict the spot-weld distortion using finite element method.

• 한국도로학회논문집
• /
• 제17권3호
• /
• pp.97-105
• /
• 2015

PURPOSES : The Toll Collection System (TCS) operated by the Korea Expressway Corporation provides accurate traffic counts between tollgates within the expressway network under the closed-type toll collection system. However, although origin-destination (OD) matrices for a travel demand model can be constructed using these traffic counts, these matrices cannot be directly applied because it is technically difficult to determine appropriate passenger car equivalent (PCE) values for the vehicle types used in TCS. Therefore, this study was initiated to systematically determine the appropriate PCE values of TCS vehicle types for the travel demand model. METHODS : To search for the appropriate PCE values of TCS vehicle types, a traffic demand model based on TCS-based OD matrices and the expressway network was developed. Using the traffic demand model and a genetic algorithm, the appropriate PCE values were optimized through an approach that minimizes errors between actual link counts and estimated link volumes. RESULTS : As a result of the optimization, the optimal PCE values of TCS vehicle types 1 and 5 were determined to be 1 and 3.7, respectively. Those of TCS vehicle types 2 through 4 are found in the manual for the preliminary feasibility study. CONCLUSIONS : Based on the given vehicle delay functions and network properties (i.e., speeds and capacities), the travel demand model with the optimized PCE values produced a MAPE value of 37.7%, RMSE value of 17124.14, and correlation coefficient of 0.9506. Conclusively, the optimized PCE values were revealed to produce estimates of expressway link volumes sufficiently close to actual link counts.

• 한국자동차공학회논문집
• /
• 제4권6호
• /
• pp.216-222
• /
• 1996

This paper presents a computational technique to predict roof crush resistance in early design stage of passenger car development. This technique use a simple F.E. model with nonlinear spring elements which represent plastic hinge behavior at weak areas. By assuming actual sections as equivalent simple sections, maximum bending moments which weak areas in major members can stand are theoretically calculated. Results from prediction of roof crush resistance are correlated well with test results.

• 한국기계가공학회지
• /
• 제7권3호
• /
• pp.36-40
• /
• 2008

This study is analyzed by the simulation of automotive steering system. The maximum equivalent stress of $2.2418{\times}109Pa$ and the maximum total displacement of 0.014929m are shown at the universal joint and its lower part respectively. As the minimum cycle of 34.047 is shown at the universal joint in case of fatigue analysis, it is possible to have greatest damage at this part. In case of natural frequency analysis at vibration, its frequency of 47 to 59Hz is occurred generally. The maximum total displacement of 0.5m is shown at handle on the natural frequency of 57 to 58Hz. And the displacement over 2m is shown at the lower part of universal joint on the natural frequency of 58 to 59Hz. As the basis of the simulation analysis of steering system, passenger's comfort of car body can be improved in the design of practical part and the design effect necessary to safe driving can be promoted.

• 한국항만학회지
• /
• 제13권1호
• /
• pp.87-100
• /
• 1999

This study was focused on analyzing the headway of various types of trailer in Pusan city with the high heavy vehicle rate. Then Passenger Car Equivalent(PCE) was calibrated in order to identify the impact of trailers in the traffic flow at the signalized intersections. To fulfill this goal types of trailer were classified into five categories such as full trailer semi-trailer unloaded semi-trailer semi-trailer loaded with 20ft container and semi-trailer loaded with 40ft container and Passenger Car Equivalents were identified. the Results are as follows: 1) The PCE’s were 2.64, 1.51, 2.09, 2.16 and 2.23 respectively. 2) The saturation flow rate on the signalized intersection was lower than that on the multi-lane highway in the big city of Korea. 3) The start-up delay on the thru lane was similar to the average value in our country but the start-up delay on the left-turn lane was longer than the average value in our country by the impact of container Vehicles.

• 동력기계공학회지
• /
• 제17권2호
• /
• pp.87-94
• /
• 2013

Applicability of organic Rankine cycle for a passenger car with 3.5 L gasoline engine to convert low grade waste heat to useful shaft power has been numerically studied. Working fluid is R134a, and the Rankine cycle is composed of boiler for recovering engine cooling water heat, super heater for recovering exhaust gas heat, scroll expander for converting waste heat to shaft power, condenser for heat emission, internal heat exchanger, and feed pump. Assuming efficiencies of 90% for the heat exchangers, 75% for the scroll expander, and 80% for the feed pump, the Rankine cycle efficiency of 5.53% was calculated at the vehicle speed of 120 km/hr. Net expander shaft output after subtracting the power required to run the pump was 3.22 kW, which was equivalent to 12.1% improvement in fuel consumption. About the same level of improvement in the fuel consumption was obtained over the vehicle speed range of 60 km/hr~120 km/hr.

• 한국산학기술학회논문지
• /
• 제11권12호
• /
• pp.4677-4684
• /
• 2010

본 연구에서는 자동차 도어에 대한 충격을 흡수하기 위한 차체의 해석을 함으로서 승차자의 안전을 조사할 수 있었다. 차체의 충돌이나 운전자의 부주의로 인한 주차 사고 때문에 자동차 도어의 손상이 일어난다. 이러한 도어는 CATIA 프로그램으로 모델링하였고, ANSYS 프로그램을 통하여 충돌에 의한 도어 모델의 파손과정을 해석하고 조사하였다. 등가응력과 변형율의 등고선들을 구하였고 충돌 하에서 도어가 어떻게 파손이 일어나는지를 확인하였다. 본 연구 결과로서 충돌안전을 고려한 도어 설계에 기여 할 것이라 사료된다.