• Plant Journal
• /
• v.13 no.2
• /
• pp.46-51
• /
• 2017

In this study, the boiler efficiency and the change of boiler combustion state with the burner operation of the uppermost layer of 870MW opposite fired coal boiler were measured. Test results showed that the boiler efficiency was high in the order of the uppermost layer simultaneous operation of the front and rear burners, the front burner, and the rear burner operation. When the front and rear burners were operated simultaneously, the heat absorption rate of water walls in the boiler furnace was uniform at four side, and the temperature deviation of the left and right steam on the convection front surface decreased. As the heat absorption rate of the boiler improved, the loss of boiler exhaust gas decreased and the coal supply amount decreased by 8 tons/hour compared to the operation of the rear burner. This will contribute not only to the reduction of fuel cost but also to the reduction of greenhouse gas emissions.

• Journal of the Korea Concrete Institute
• /
• v.17 no.2 s.86
• /
• pp.171-177
• /
• 2005

Even though the cost associated with the repair and rehabilitation of existing structures are rapidly increasing, vast number of the repaired and rehabilitated structures do not function properly as expected during their remaining service lives. This paper focused on the flexural behavior of reinforced concrete slabs repaired and reinforced by PS strand and polymer mortar in the tension face. The slabs have the size of 700${\times}120{\times}$2200 m and 700${\times}120{\times}$1300 mm. Variables of experiment were space of strengthening, chipping, the number of strand, the kind of mortar in this experimental study. Attention is concentrated upon overall bending capacity, deflection, ductility and failure mode of repaired and reinforced slabs. Test results show that deflection of repaired and reinforced slabs reduced to approximately $40 \%$ comparison to standard slabs. Boundary cracking of chipping slab started ultimate load afterward. Concrete-mortar interface cracked 64.5 kN in repaired slab with AP mortar and 36.0 kN in repaired slab with general polymer mortar. Reinforcement effect increased with reducing space of strand. Also, Reinforcement effects are more by strand than by polymer mortar.

• Journal of the Korea Concrete Institute
• /
• v.17 no.4 s.88
• /
• pp.499-504
• /
• 2005

Polymer concrete shows excellent mechanical properties and chemical resistance compared with conventional normal cement concrete. The polymer concrete Is drawing a strong interest as high-performance materials in the construction industry Resins using recycled PET offer the possibility of a lower source cost of materials for making useful polymer concrete products. Also the recycling of PET in polymer concrete would help solve some of the solid waste problems Posed by plastics and save energy. An objective of this paper is to estimate the damage of sulfuric acid, through investigating recycled PET polymer concrete, immersed at sulfuric acid solution for 84 days. As a result of testing, recycled PET PC, used $CaCO_3$ as filler, makes a problem of appearance and strength if they are exposed for long term at corrosion environment. On the other hand, recycled PET PC, used fly-ash as filler, had less effect on decrease in weight and strength. Recycled PET PC is excellent chemical resistance, resulting in the role of unsaturated polyester resin which consists of polymer chain structure accomplishes bond of aggregates and filler strongly. Also, recycled PET PC, used fly-ash as filler, is stronger resistance of sulfuric acid corrosion than $CaCO_3$, because it is composed of $SiO_2$ and very strong glassy crystal structure. Therefore, recycled PET PC, used fly-ash as filler, is available under corrosion circumstances like sewer pipe or waste disposal plant.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.24 no.5
• /
• pp.781-793
• /
• 2014

A Public Key Infrastructure (PKI) is security standards to manage and use public key cryptosystem. A PKI is used to provide digital signature, authentication, public key encryption functionality on insecure channel, such as E-banking and E-commerce on Internet. A soft-token private key in PKI is leaked easily because it is stored in a file at standardized location. Also it is vulnerable to a brute-force password attack as is protected by password-based encryption. In this paper, we proposed a new method that detects private key compromise and is probabilistically secure against a brute-force password attack though soft-token private key is leaked. The main idea of the proposed method is to use a genuine signature key pair and (n-1) fake signature key pairs to make an attacker difficult to generate a valid signature with probability 1/n even if the attacker found the correct password. The proposed method provides detection and notification functionality when an attacker make an attempt at authentication, and enhances the security of soft-token private key without the additional cost of construction of infrastructure thereby extending the function of the existing PKI and SSL/TLS.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.5
• /
• pp.671-679
• /
• 2016

Bridges, which constitute one of the key facilities in a social infrastructure, are easily accessed and used by users, so that keeping their performance above a certain level is essential. According to various cases in the U.S., Japan and Europe with a long construction history, it is expected that the maintenance cost of bridges in Korea will increase continuously in the future, so a rational decision making system based on engineering factors is necessary to optimize the performance of and maintain them by allocating the limited budget efficiently. This study is a preliminary basic study for the purpose of developing a common asset management system for managing all of the bridges and maintaining the level of service provided by them. The scope of this preliminary study is limited to bridges in urban areas. The bridge asset management system for bridges in urban areas, their level of service (LOS) and performance measure (PM) were developed by carrying out a workshop consisting of both experts and stakeholders. The analysis on the weights of the value and performance measure for each performance indicator was carried out by using the multi-attribute utility theory and the AHP method. In order to confirm the application of the weight of the performance measure and value of the performance indicator, six bridges in an example city were selected, LOS analysis was applied and its results were reviewed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.5
• /
• pp.3499-3510
• /
• 2015

To cope with the increased demand on the intra-city transportation by urban rails, the introduction of the light rail transit (LRT) systems has been expedited in Korea due to the possible reduction of both the development and operation costs from adopting LRT systems. The LRT systems have so far been designed, constructed and operated based on the corresponding law and regulations. It has been conceived that fully complying with the existing guidelines may incur some extra costs on LRT. In addition, the present design of LRT stations seems to require unnecessarily long flow of passengers traffic, particularly for disabled people. In this paper, as an approach to solving the aforementioned issues, an introduction of 'LRT stops' has been studied where the stops are similar in concept to bus stops and are intended to replace the stations of a bigger scale in general. Specifically, necessary guidelines for design have been developed by modifying the existing ones to be fit with LRT stops. A design case was also presented to evaluate them. The effective use of the results reported here will provide an opportunity of cost reduction in connection with the construction and operation, and also let people benefit from convenient use of rails, thereby resulting in enhanced transportation welfare.

• Journal of KIISE:Databases
• /
• v.33 no.2
• /
• pp.201-213
• /
• 2006

A time-series database is a set of time-series data sequences, each of which is a list of changing values of the object in a given period of time. Subsequence matching is an operation that searches for such data subsequences whose changing patterns are similar to a query sequence from a time-series database. This paper addresses a performance issue of time-series subsequence matching. First, we quantitatively examine the performance degradation caused by the window size effect, and then show that the performance of subsequence matching with a single index is not satisfactory in real applications. We argue that index interpolation is fairly useful to resolve this problem. The index interpolation performs subsequence matching by selecting the most appropriate one from multiple indexes built on windows of their inherent sizes. For index interpolation, we first decide the sites of windows for multiple indexes to be built. In this paper, we solve the problem of selecting optimal window sizes in the perspective of physical database design. For this, given a set of query sequences to be peformed in a target time-series database and a set of window sizes for building multiple indexes, we devise a formula that estimates the cost of all the subsequence matchings. Based on this formula, we propose an algorithm that determines the optimal window sizes for maximizing the performance of entire subsequence matchings. We formally Prove the optimality as well as the effectiveness of the algorithm. Finally, we perform a series of extensive experiments with a real-life stock data set and a large volume of a synthetic data set. The results reveal that the proposed approach improves the previous one by 1.5 to 7.8 times.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.22 no.3
• /
• pp.261-275
• /
• 2020

When excavating a small cross-section tunnel in a fault fracture zone using the shield TBM method, there is a high possibility of excessive convergence and collapse. Appropriate ground reinforcement is required to minimize construction cost loss and trouble due to a fault fracture zone. In this study, the optimal reinforcement area was suggested and the surrounding ground behavior was investigated through numerical analysis using MIDAS GTS NX (Ver. 280). For the parameters, the width of the fault fracture zone, the existence of fault gouge, and the groundwater level and depth of cover were applied. As a result, when there is not fault gouge, the convergence and ground settlement are satisfied the standard when applying ground reinforcement by up to 0.5D. And, due to the high permeability coefficient, it is judged that it is necessary to apply 0.5D reinforcement. There is a fault gouge, it was possible to secure stability when applying ground reinforcement between the entire fault fracture zone from the top of the tunnel to 0.5D. And, because the groundwater discharge occurred within the standard value due to the fault gouge, reinforcement was unnecessary.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.2
• /
• pp.741-749
• /
• 2019

A hydraulic breaker attached to an excavator is a kind of constructuion equipment which is used for the disassembling of buildings, crashing road pavement, breaking rocks at quarry and etc. Therefore, the performance of the hydraulic breaker is mainly evaluated by the impact quantity and impact efficiency, which is an important factor for both the manufacturer and the user. In this paper, modeling and simulation for the prediction of the impact of the hydraulic breaker was conducted according to hydraulic pressure area and operating conditions of the hydraulic valve and piston using the commercial tools SimulationX for the 20ton hydraulic breaker which is mainly used in construction site. In order to verify the reliability of modeling and simulation, the results of previous experimental studies were compared and verified. The results of this study are expected to be useful for predicting the impact of the hydraulic breaker at the design stage before manufacturing and for studying parameters for improving the impact quantity. In addition, the manufacturer predicts that the development time and cost will be reduced through trial and error prevention by predicting the impact of the hydraulic breaker through the results of this paper.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.6
• /
• pp.561-568
• /
• 2020

Wave measurements using X-band radar have many advantages compared to other wave gauges including wave-rider buoy, P-u-v gauge and Acoustic Doppler Current Profiler (ADCP), etc.. For example, radar system has no risk of loss/damage in bad weather conditions, low maintenance cost, and provides spatial distribution of waves from deep to shallow water. This paper presents new methods for estimating significant wave heights of X-band marine radar images using Artificial Neural Network (ANN). We compared the time series of estimated significant wave heights (Hs) using various estimation methods, such as signal-to-noise ratio (${\sqrt{SNR}}$), both and ${\sqrt{SNR}}$ the peak period (TP), and ANN with 3 parameters (${\sqrt{SNR}}$, TP, and Rval > k). The estimated significant wave heights of the X-band images were compared with wave measurement using ADCP(AWC: Acoustic Wave and Current Profiler) at Hujeong Beach, Uljin, Korea. Estimation of Hs using ANN with 3 parameters (${\sqrt{SNR}}$, TP, and Rval > k) yields best result.