• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.5
• /
• pp.1-7
• /
• 2012

Chemical composition, morphological properties and papermaking properties of Sasa quelpaertensis Nakai were investigated in order to use it comprehensively. The lignin contents of stalks and leaves were 18.8% and 15.3% and the holocellulose contents were 63.3% and 48.6% respectively. The contents of ash and the amount of water extract showed the higher value than those of wood or other bamboo species. The average fibers length and width of Sasa quelpaertensis Nakai were 780 ${\mu}m$ and 14.8 ${\mu}m$. The fibers of Sasa quelpaertensis Nakai stalk had thinner width and more slender structure than those of softwood. The handsheet made of Sasa quelpaertensis Nakai alkaline pulp showed higher in tensile strength and bulkier structure than those of handsheet made of soft wood unbleached kraft pulp.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.30 no.1
• /
• pp.7-17
• /
• 1998

With the advent of CLSM in the end of 1980s, it has been applied to the field of pulp and paper science in various ways. This study showed the potentials of CLSM In analyzing a change of pulp fiber and paper properties before and after mechanical treatment. In particular, a quantification of internal fibrillation has been done using cross-sectional images of fibers and image analysis technique, then evaluated the effects of fiber wall delamination on fiber and paper properties. It showed that the delaminated fibers were closely associated to development of the interfiber bonding in a fiber network. The CLSM made it possible to investigate a density profile along the sheet thickness, which was created by some papermaking processes like pressing, drying and calendering. Through the attempt to observe the forming procedure of a fiber network during handsheet making, the CLSM images showed that the pressing stage was considered greatly to contribute to generation of interfiber bonding with removing a free water and partly a bound water between fibers. In addition, the CLSM could be used to illustrate not only a surface profile of paper showing the extent of smoothness or roughness, but also a density profile in a B-direction of the network. Finally it became evident that the CLSM could be used as an excellent tool to predict development in fiber and paper properties before and after mechanical treatment during papermaking processes.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.4
• /
• pp.71-77
• /
• 2010

To utilize modified pulp fibers in papermaking system, it is necessary to evaluate the interaction between modified fibers and papermaking additives. Fluorescent whitening agent (FWA) is an important additive which has been widely used for production of writing and printing paper. We modified pulp fiber surface by Layer-by-Layer multilayering of polyelectrolytes, and investigated the interaction between these fibers and FWA used in internal addition or surface treatment. Pulp fiber with cationic surface charge showed a good affinity to internal FWA. For FWA in surface sizing agent, whiteness and brightness of paper was dependent on pickup weight and polyelectrolyte type. Pulp fibers with C-starch/PSS multilayer showed better optical properties than poly-DADMAC/PSS treatment. It indicated that polyelectrolyte type in Layer-by-Layer multilayering as well as a good affinity to FWA is important to get better whiteness and brightness.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.2
• /
• pp.65-72
• /
• 2008

This work evaluated the extractability of tobacco stem biomass for the papermaking type Reconstituted Tobacco Sheet(RTS). The effects of the soaking conditions on the hydration of stem biomass and the effects of the hydrated state on the mechanical extraction were investigated. In order to simulate the mechanical expression process of a papermaking type RTS mill, for example, the screw press process, the novel mechanical pressing analyzer was developed for this study. The hydration of stem biomass by soaking process was greatly affected by the soaking time and the soaking temperature. The longer soaking time and the higher soaking temperature resulted in the higher hydrated stem biomass. Since the higher hydrated stem had more combined water in the inner structure and resulted in the more flexible structure, the higher hydrated stem leaded to the more compressed filter cake and the higher water contents in the filter cake after the mechanical pressing. The pilot pulping experiments showed the difference in hydration and extractability between burley and bright tobacco stem. The bulkier structure of the burley stem resulted in the faster hydration by pilot pulping and leaded to the larger reduction in water soluble components. And the hydration process showed the major influence on the separation efficiency of water soluble components.

• Journal of the Korean Society of Tobacco Science
• /
• v.27 no.2
• /
• pp.195-200
• /
• 2005

The goal of refining is to treat fibers so they meet the requirements of the papermaking process. The refining process in papermaking has great influence on the quality of the final product by changing the fiber properties, such as fiber length, shape, fine contents and so on. In this study, the effect on the morphological change of fibers by the refining conditions were investigated using the fiber morphology analyzer. Fiber morphology analyzer used to determine which pulps are suitable for producing particular products. Furthermore it is widely used in paper mills to monitor paper quality. The morphological change of fibers according to refining conditions were evaluated out by measuring fiber, shive and fine. In the fiber morphology, the domestic reconstituted tobacco fiber has the bigger average fiber length value than that of the foreign reconstituted tobacco.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.4
• /
• pp.9-15
• /
• 2013

An oxidized starch ester was prepared and used for surface sizing. Esterification of starch decreased both Brookfield viscosity and Brabender viscosity substantially even though the solids level was increased by 2% from 14% to 16%. Surface sizing with the esterified starch gave better performance in tensile strength, stiffness and compressive strength than surface sizing with oxidized starch in the laboratory. Advantages in strength improvement, however, were not obtained when it was applied in commercial papermaking process. This was attributed to the fact that the influence of starch types has been nullified by high pressure penetration that occurs in the commercial papermaking process. Drying energy consumption, however, decreased by 3.3% by substituting the low solids oxidized starch with a high solids starch ester.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.3
• /
• pp.18-24
• /
• 2000

To evaluate the efficiency of various cationic starches in improving retention drainage and strength properties of newsprints which are being made using extensive amount of domestic recycled wastepapers in a highly closed papermaking system diverse cationic starches have been prepared and tested. In the case of cationic starches with low charge density as the degree of substitution increas-es fines retention increased. Results also showed that the retention efficiency decreased sub-stantially for cationic starches with low DS when the conductivity of white water inceased. Tensile strength increased with the addition of cationic starches and then decreased. On the other hand internal bonding strength increased linearly with the addition of cationic starch. Oxidizing treatment of cationic starch was detrimental for retention and freeness improve-ment. Also crosslinking treatment of wet processed cationic starches made cationic starches less effective in retention and drainage.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.39 no.2 s.120
• /
• pp.1-8
• /
• 2007

To examine the feasibility of dry forming technology for papermaking, a dry forming mold (DFM) was developed and evaluated. Main fanning section of DFM was a cylindrical tube, and at the top of the mold a stirring equipment was placed to disperse dry fibers. These fibers were screened using a hole type screen plate placed just under the stirring equipment and dropped freely on the fanning wire located 0.9 m below of the screen plate to form a dry fiber pad. The vertical and horizontal velocity of air flow in the forming cylinder were evaluated and analyzed to find the most effective method of air flow control in the cylinder. Humidification and pressing conditions to obtain a decent dry fanned papers were examined. Results showed dry fanned papers can be prepared with this dry forming mold. And this mold can be used to examine the effect of the papermaking process factors including pressing pressure, drying temperature, humidification on sheet quality of dry formed papers.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.11
• /
• pp.1819-1824
• /
• 2006

The general objective of the present study was to investigate the potential application of the UV spectroscopic method for determination of the polymeric additives present in papermaking fibrous stock solutions. The study also intended to establish the surface-chemical retention model associated with the adsorption kinetics of additives on fiber surfaces. Polyamide epichlorohydrin (PAE) wet strength resin and imidazolinium quaternary (IZQ) softening agents were selected to evaluate the analytical method. Concentrations of PAE and IZQ in solution were proportional to the UV absorption at 314 and 400 nm, respectively. The time-dependent behavior of polymeric additives obeyed a mono-molecular layer adsorption as characterized in Langmuir-type expression. The kinetic modeling for polymeric adsorption on fiber surfaces was based on a concept that polymeric adsorption on fiber surfaces has two distinguishable stages including initial dynamic adsorption phase and the final near-equilibrium state. The simulation model predicted not only the real-time additive adsorption behavior for polymeric additives at high accuracy once the kinetic parameters were determined, but showed a good agreement with the experimental data. The spectroscopic method examined on the PAE and IZQ adsorption study could potentially be considered as an effective tool for the wet-end retention control as applied to the paper industry.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.4
• /
• pp.25-31
• /
• 2012

Ionic trash in furnish decreases retention and drainage performance of the microparticle retention system using recycled fibers in closed papermaking system. Two retention systems, such as the microparticle system and the PEO/cofactor system, were compared and analyzed to improve retention. The PEO/cofactor system achieved similar retention performance at low addition level as the microparticle system. Optimum ratio of PEO/cofactor dual polymer system was 1:10. Ash retention was increased when using the fixing agent. As the TMP ratio increased, the PEO/cofactor system was more efficient in retention and drainage than the other system. The high molecular weight and non-ionic polymer retention system had less effect on flocculation hindrance than the traditional electrostatic retention system.