• Steel and Composite Structures
• /
• 제41권6호
• /
• pp.861-871
• /
• 2021

This study aims at investigating the hysteretic performance of a novel composite wall panel fabricated by infilling aerated concrete blocks into a novel light-steel frame used for low-rise residential buildings. The novel light-steel frame is consisted of two thin-wall rectangular hollow section columns and a truss-beam assembled using patented U-shape connectors. Two bare light-steel frames and two composite wall panels have been tested to failure under horizontal cyclic loading. Hysteretic curves, lateral resistance and stiffness of four specimens have been investigated and analyzed. Based on the testing results, it is found that the masonry infill can significantly increase the lateral resistance and stiffness of the novel light-steel frame, about 2.3~3 and 21.2~31.5 times, respectively. Failure mode of the light-steel frame is local yielding of the column. For the composite wall panel, firstly, masonry infill is crushed, subsequently, local yielding may occur at the column if loading continues. Hysteretic curve of the composite wall panel obtained is not plump, implying a poor energy dissipation capacity. However, the light-steel frame of the composite wall panel can dissipate more energy after the masonry infill is crushed. Therefore, the composite wall panel has a much higher energy dissipation capacity compared to the bare light-steel frame.

• 한국초전도ㆍ저온공학회논문지
• /
• 제15권4호
• /
• pp.53-58
• /
• 2013

KSTAR in-vessel cryo-pump has been installed in the vacuum vessel top and bottom side with up-down symmetry for the better plasma density control in the D-shape H-mode. The cryogenic helium lines of the in-vessel cryo-pump are located at the vertical positions from the vacuum vessel torus center 2,000 mm. The inductive electrical potential has been optimized to reduce risk of electrical breakdown during plasma disruption. In-vessel cryo-pump consists of three parts of coaxial circular shape components; cryo-panel, thermal shield and particle shield. The cryo-panel is cooled down to below 4.5 K. The cryo-panel and thermal shields were made by Inconel 625 tube for higher mechanical strength. The thermal shields and their cooling tubes were annealed in air environment to improve the thermal radiation emissivity on the surface. Surface of cryo-panel was electro-polished to minimize the thermal radiation heat load. The in-vessel cryo-pump was pre-assembled on a test bed in 180 degree segment base. The leak test was carried out after the thermal shock between room temperature to $LN_2$ one before installing them into vacuum vessel. Two segments were welded together in the vacuum vessel and final leak test was performed after the thermal shock. Commissioning of the in-vessel cryo-pump was carried out using a temporary liquid helium supply system.

• 대한인간공학회지
• /
• 제18권2호
• /
• pp.35-45
• /
• 1999

Driver centered vehicle design is the important factor for driver's safety, product quality, and so on. Therefore, people has recently recognized the importance of driver centered vehicle design. Especially, in the focus of driver-vehicle interaction system, it is very important factor to ergonomic design of vehicle cockpit. In this study, Sketch Map method was used to measure of driver's cognitive map on IP(Instrument Panel) that is the basic factor to ergonomic design for vehicle cockpit. The compatibility of Sketch Map method was validated for the measurement of driver's cognitive map and then the accuracy between two groups was analyzed using Sketch Map method. Subjects were divided in two groups, the first group of subjects has their own vehicles and driver license, and the second group of subjects doesn't have own vehicle but has driver license. The result showed that for the case of the first group, the shape of IP in the cognitive map was influenced by IP of their each vehicle. However, for the case of the second group, it showed the difference between IP in the cognitive map and IP of experienced vehicle many times because they have been driving various type of vehicle. So, the shape of IP in the cognitive map was influenced by various type of IP.

• 한국인쇄학회지
• /
• 제29권2호
• /
• pp.45-58
• /
• 2011

Gravure off-set printing recently is used in electronics display market. This method has advantages of mass production and high printing speed. It is also fine pattern can be implemented. We have manufactured low-curable conductive Ag pastes for gravure off-set printing. When printing, the pastes be used different silver powder shape because of the printing characteristics. The pastes were prepared with silver powder by silver powder shape and size, epoxy resin, solvent and homogenized on a standard three-roll mill. And the pastes exhibited a shear-thinning flow at viscosity profile. Moreover the adhesive strength and resistivity of silver film had a good characteristics. With the manufactured paste in this study, touch panel had is manufactured and it had $4{\times}10-5{\Omega}.cm$.

• 한국가구학회지
• /
• 제23권2호
• /
• pp.195-206
• /
• 2012

Since of 2000s, Office furniture have been much changes in the design as the expanding demand for the diversity and variability of office space. Especially, OA System Furniture including Panel System were developed by the shape and configuration considering the members' communication and teamwork. However, It is limited to the situation for the leading manufacturer of office furniture, Most small business cope with a negative policy because development personnel and expense. Thus, Accounted for the majority of the office furniture manufacturing, Small and medium-sized furniture manufacturers are needed measures of development that reflect these realities, rapid and practical. This study suggests redesign in a way that a small and medium-sized furniture manufacturers to overcome the limited design development environment and rapidly respond to changing market conditions. And this study has an intend to develop the Office Panel System.

• 한국공간구조학회논문집
• /
• 제6권2호
• /
• pp.85-92
• /
• 2006

본 연구에서는 철근콘크리트 프리캐스트 대형판의 접합부 설계방법 및 해석방법에 대해서 연구를 수행하였다. 접합부의 설계방법은 수평접합부와 수직접합부의 구조적 거동에 대한 안정성 및 일체성을 확보하기 위한 설계법을 제시하였고, 접합부의 해석은 강체스프링 모델에 의한 탄소성해석을 수행 하였다.

• 한국공작기계학회논문집
• /
• 제12권6호
• /
• pp.71-76
• /
• 2003

Optimal design of panel with trapezoidal type stiffeners was studied using linear and nonlinear deformation theories. Also analysis method was using closed-form analysis and finite difference energy methods, respectively. Various bucking load factors are obatined for stiffened laminated composite panel with trapezoidal type stiffeners and various aspect ratios, which are made from Carbon/Epoxy USN 125 prepreg and are simply-supported on four edges under uniaxial compression. Optimal design analyses are carried out by the nonlinear search optimizer, ADS.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계 학술대회논문집(수송기계편)
• /
• pp.122-125
• /
• 2005

This study is an measurement and prediction of transmission loss through dash panel with multi-path in a vehicle. Measurement results of transmission loss are derided by sound power measured using the sound intensity method under locating a sound source in the anechoic room and reverberant room, respectively. Prediction one is decided by multi-path analysis of dash panel composed by a various part of materials and complicated shape. Finally, two results show a great agreement between measured and predicted transmission loss.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1506-1511
• /
• 2003

This paper describes an automatic weld seam tracking method of plasma arc welding system designed for the corrugation panel that consists of a linear section and a curved section with various curvatures. Due to the complexity of the panel shape, it is difficult to find a seam and operate a torch manually in the welding process. So, the laser vision sensor for seam tracking is designed for sensing the seam position and controlling a torch automatically. To achieve precise seam tracking, the design of sensor head, image simulation, and calibration are carried out. Through a series of experiment result, compensation algorithm is added and real time error compensation is achieved. The experiment result shows that this vision sensor works effectively. It will provide more precise welding performance and convenience to the operator.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권5호
• /
• pp.614-621
• /
• 2007

The fishing boat propulsion system employing the modified stern shape and the tunnel to protect a propeller is developed to increase the cruise speed and reduce he problem resulting from the open propeller accidentally catching the waste net and able on the sea. Using 3 different tunnel types, the model test was performed in the circular water channel and the panel method based on the potential theory is applied to analyze the open water performance of the propeller. In the numerical analysis using he potential-based panel method, it calculates the hydrodynamic interaction between the propeller and the tunnel and evaluates the effect of the tunnel geometry. From the numerical and experimental results differing tunnel geometries, the propulsion efficiency is increased by the larger diameter of the inlet than the outlet of the tunnel and the smaller gap between the propeller tip and the tunnel internal surface. These results provide the information of the propeller system with the tunnel and the hydrodynamic interaction between the propeller and the tunnel.