• Tribology and Lubricants
• /
• 제5권2호
• /
• pp.77-82
• /
• 1989

The influences of ram pressure on the performances of tilting-pad journal bearings are investigated experimentally. The test rig consists of a single tilting-pad and a rotating journal. Film thicknesses and pressure distribution of the lubricating film are measured continuously for several values of coordinate of the pivot position and journal speed. The findings of the investigation are as follows: (]) According as the journal speed increases the ram pressure increases, maximum pressure decreases and the pivot position which maximize the minimum film thickness shifts toward the leading edge. (2) The ram pressure makes it possible to generate the converging wedge and the positive pressure between the pad and the journal even when the pad is supported at the points between the leading edge and the center of the pad. (3) The influence of the ram pressure on the performance of tilting pad bearings is significant and must be considered in the design of these bearings.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제29회 춘계학술대회
• /
• pp.111-118
• /
• 1999

In this paper, linearized dynamic characteristics of parallel line pivoted pad thrust bearing(hereinafter refer to PLP thrust bearing) was analyzed by perturbation method with inlet pressure. Inlet pressure and excitation frequency irfluence dynamic characteristics of PLP thrust bearing at all operating condition, such as angular pivot position, mass of pad. Therefore, the characteristics is have to analyzed with inlet pressure, excitation frequency, mass of pad and thickness of pad. Otherwise, the analysis is able to estimate the characteristics over or under.

• Tribology and Lubricants
• /
• 제16권4호
• /
• pp.274-281
• /
• 2000

In this paper, linearized dynamic characteristics of parallel line pivoted pad thrust bearing (here-inafter refer to PLP thrust bearing) was analyzed by perturbation method with inlet pressure. Inlet pressure and excitation frequency influence dynamic characteristics of PLP thrust bearing at all operating conditions, such as angular pivot position, mass of pad. Therefore, the characteristics have to be analyzed with inlet pressure, excitation frequency, mass of pad and thickness of pad. Otherwise, the analysis may be over or under estimate.

• Tribology and Lubricants
• /
• 제10권4호
• /
• pp.33-42
• /
• 1994

An influence of inlet pressure on the performance of sector-shaped pad thrust bearings is investigated theoretically. The optimum conditions of film thickness or the optimum positions of pivot are found through the evaluation of load capacity for all available conditions of film thickness, under the operating conditions which the thermal and pad deformation effects can be neglected. The bearing performance including the inlet pressure effects is obtained for a wide operating ranges that inertia parameter(Re$^{*}$) is up to unity, and for the various cases of pad extent angle (number of pad) and the three cases of the angle between pads. The results show that the inlet pressure has a large influence on the performance of sector-shaped pad thrust bearings. In the design of sector-shaped pad bearings, due to the inlet pressure, the optimum number of pad is varied with the operating speed and the angle between pads, and the optimum position of pivot is located toward the leading edge along with the operating speed increases.

• Tribology and Lubricants
• /
• 제2권1호
• /
• pp.61-68
• /
• 1986

Effects of the ram-pressure on the THD-performance of pivoted pad thrust bearings are investigated experimentally. A sector-shaped tilting pad thrust bearing and a rotating disk are used. Temperature distribution on the disk surface as well as on the pad surface, distribution of the pressure generated within the fluid film, and the film thickness are measured continuously in the circumferential direction after thermal equilibrium is established. The ram-pressure is proportional to the mean pressure of oil film and to the rotational speed of the disk and affects the maximum pressure and the pressure distribution. The temperature rise on the mating surface of the disc and the pad, contacting with the oil film, is proportional to to the bearing load and the disk speed. The ram-pressure and the temperature rise on the disk surface are dominant factors that affect the THD-performance of pivoted pad thrust bearings.

• Tribology and Lubricants
• /
• 제14권1호
• /
• pp.7-13
• /
• 1998

The static characteristics of a five-pad tilting pad journal bearing of load on pad (LOP) type have been investigated experimentally under the different values of bearing load and shaft speed. The diameter and length of the bearing are 300.91 mrn and 149.8 mm, reslx;ctively. Circumferential distribution of the film pressure, film thickness, journal surface temperature and beating surface temperature are measured. A noticeable inlet pressure rise is observed at the entrance of each pad, especially the bottom pad. The inlet pressure is increased by the increase of shaft speed as well as bearing load. In the five-pad tilting pad joumal bearing of LOP type, almost all of beating load is being carried only by the bottom pad. The maximum bearing surface temperature is observed at near the minimum film thickness. It is observed that the metal temperature of the mid-plane is higher than that of the edge at the inlet region, while the metal temperature of the edge is higher than that of the mid-plane at the outlet region.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제27회 춘계학술대회
• /
• pp.235-240
• /
• 1998

The inlet pressure build-up at the leading edge of bearings and its effects on the static performances are investigated theoretically. The performance analyses of air-lubricated tilting pad bearings are carried out considering the inlet pressure which is obtained by means of momentum conservation method. The results show that inlet pressure is above atmosphere pressure in front of leading edge of tilting pad bearing and there is a significant influence of the inlet pressure on the performance of bearings.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.359-361
• /
• 2006

As circuits become increasingly complex and devices sizes shrinks, the demands placed on global planarization of higher level. Chemical Mechanical Polishing (CMP) is an indispensable manufacturing process used to achieve global planarity. In the CMP process, Diamond Disk (DD) plays an important role in the maintenance of removal rate. According to studies, the cause of removal rate decrease in the early or end stage of diamond disk lifetime comes from pad surface change. We also presented pad cutting rate (PCR) as a useful cutting ability index of DD and studied PCR trend about variable parameters that including size, hardness, shape of DD and RPM, pressure of conditioner It has been shown that PCR control ability of pressure and shape is superior to RPM and size. High pressure leads to a decrease of cell open ratio of pad surface because polyurethane of pad is destroyed by pressure. So low pressure high RPM condition is a proper removal rate sustain. By examining correlations between RPM and pressure of conditioner, it has been shown that PCR safe zoneto satisfy proper removal rate has the range 0.06mm/hr to 0.12mm/hr.

• Tribology and Lubricants
• /
• 제5권2호
• /
• pp.68-76
• /
• 1989

In this paper, the influence of ram-pressure on the static and dynamic characteristics of infinite width tilting-pad journal bearing is investigated theoretically. The ram-pressure is obtained by assumption of conservation of mechanical energy of the lubricant flow through the leading edge of the pad. The pressure in the lubricating film is numerically calculated using the ram-pressure obtained as the inlet pressure boundary condition of the pad. The static equilibrium state of tilting-pad journal bearing is determined by Newton-Raphson iteration method. A numerical results are presented in graphic form and relationships between the ram-pressure and the static and dynamic characteristics are discussed.

• 한국기계가공학회지
• /
• 제1권1호
• /
• pp.89-100
• /
• 2002

The purpose if this research was to improve the pressure distribution on the disk brake pad Not uniform pressure distribution on the disk brake pad generate the unbalance wear of it and the unbalance wear of disk brake pad generate vibration, noise, heat and reduce the braking capacity. For improve the pressure distribution on the pad in this research, upper face of caliper housing finger was cut. Two kinds of caliper which uncut and cut of finger face were compared the stress distribution by FEM analysis and real experiment. Also natural frequency and deforming displacement ware calculated. It was understood that pressure distribution could Improve by cut inside upper face of caliper housing finger.