• Wind and Structures
• /
• v.29 no.4
• /
• pp.235-246
• /
• 2019

Wind loading is one of important loadings that should be considered in the design of large hyperbolic natural-draught cooling towers. Both external and internal surfaces of cooling tower are under the action of wind loading for cooling circulating water. In the previous studies, the wind loads on the external surface attracted concernedly attention, while the study on the internal surface was relatively ware. In the present study, the wind pressure on the internal surface of a 220 m high cooling tower is measured through wind tunnel testing, and the effect of ventilation rate of the packing layer on internal pressure is a major concern. The characteristics of internal wind pressure distribution and its effect on wind-induced responses calculated by finite element method are investigated. The results indicate that the wind loading on internal surface of the cooling tower behaves remarkable three-dimensional effect, and the pressure coefficient varies along both of height and circumferential directions. The non-uniformity is particularly strong during the construction stage. Analysis results of the effect of internal pressure on wind-induced responses show that the size and distribution characteristics of internal pressure will have some influence on wind-induced response, however, the outer pressure plays a dominant role in the wind-induced response of cooling tower, and the contribution of internal pressure to the response is small.

• Archives of Plastic Surgery
• /
• v.46 no.5
• /
• pp.421-425
• /
• 2019

Background The endoscopic transnasal approach is widely used for reconstructing the medial orbital wall by filling it with a silicone sheet or Merocel, but this technique has the disadvantage of retaining the packing for a long time. To overcome this drawback, a method of positioning an absorbable plate in the orbit has been introduced, but there is a risk of defect recurrence after the plate is absorbed. Here, the authors report the results of a novel surgical technique of placing a nonabsorbable titanium mesh with porous polyethylene into the orbit through the endoscopic transnasal approach. Methods Fourteen patients underwent surgery using the endoscopic transnasal approach. Preoperative computed tomography (CT) was used to calculate the size of the bone defect due to the fracture, and the titanium mesh was designed to be shorter than the anteroposterior length of the defect and longer than its height. The titanium mesh was inserted into the orbit under an endoscopic view. The authors then confirmed that the titanium mesh supported the orbital contents by pressing the eyeball and finished the operation. Immediately after surgery, CT results were evaluated. Results Postoperative CT scans confirmed that the titanium mesh was well-inserted and in the correct position. All patients were discharged without any complications. Conclusions We obtained satisfactory results by inserting a titanium mesh with porous polyethylene into the orbit via the transnasal approach endoscopically.

• Korean Chemical Engineering Research
• /
• v.46 no.2
• /
• pp.414-422
• /
• 2008

Adsorption experiments for $H_2$, $CH_4$, CO, $CO_2$ on activated carbon and zeolite 5A were performed by static volumetric method. A 4-bed pressure swing adsorption (PSA) process was to study separation of hydrogen from multi-component mixture gases ($H_2$ 72.2%, $CH_4$ 4.06%, CO 2.03%, $CO_2$ 21.6%). Dual-site langmuir (DSL) isotherm showed good or fair agreement with the experimental results. The optimum height of activated carbon layer was 55 cm with breakthrough results on the packing ratio of activated carbon to zeolite 5A. In PSA process, the effects of the process parameters such as total cycle time ($T_c$), ${\Delta}P$ at the provide purge step and adsorption pressure on the PSA performance were studied experimentally and theoretically.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.34 no.2
• /
• pp.322-328
• /
• 2007

The first molar is important for mastication and also it plays roles to formation of vertical occlusion and growth of jaw bone after mixed dentition. Impaction of mandibular first molar can result in a short lower facial height, formation of a follicular cyst, pericoronal inflammation, resorption of the roots of neighboring teeth and malocclusion. The options of treatment plans are as follows; observation, surgical exposure, orthodontic traction, surgical relocation and extraction. Surgical exposure could be considered as a basic treatment plan. For surgical exposure it is important to maintain patent channel between the crown and the normal eruptive path into the oral cavity, many techniques including cementation of a celluloid crown, packing with zinc oxide-eugenol surgical pack are used. In these cases, we could observe spontaneous eruption of mandibular first molar using surgical exposure with or without removal of odontoma. Also we could obtain the main patency effectively and conveniently by using surgical pack and translucent retainer.

• Resources Recycling
• /
• v.19 no.6
• /
• pp.43-50
• /
• 2010

The crisis of energy gives rise to the growing concerns over continuing uncertainty in the energy market. Under these circumstances, there are also increasing interests on coals. In particular, Low Rank Coal (LRC) is receiving gradual attentions from green industry. But due to is high moisture content range from 30 - 60%, drying process has to be preceded before being utilized as power plant. In this study drying kinetics of LRC is induced by using a fixed-bed reactor. The drying kinetics was evaluated in from of the particle size, the inlet gas temperature, the drying time, the gas velocity, and the LID ratio. The consideration of the reynold's number was taken for correction of gas velocity, particle size and LID was taken for correction of reactor diameter, packing height of coal. As being seen as characteristic of drying coal, it can be found that fixed-bed reactor can contributed to active drying of free water. In this sense, it could be considered that phase boundary reaction is appropriate mechanism.

• Journal of the Korean Wood Science and Technology
• /
• v.17 no.2
• /
• pp.34-64
• /
• 1989

Corner block with anchor bolt(CBA) joint method used in knock-down type table furniture manufacturing can reduce the packing and transporting cost. Unfortunately. it also has the disastrous defect to be loosend and unstable during the service life mainly due to fatigue and creep(repeated and prolonged loading). So 22 joint groups constructed were tested to evaluate the effect of some design factors related to the size of side rail(apron). block attachment to side rail. and the number of anchor bolt as well as the effect of the type of corner block(mitered type vs. rectangular type) Usable strength from the stiffness coefficients of each joint group were analysed with SPSS /PC+ and described as the criteria of CBA joint construction. The conclusions were as follows: The height of side rail(50, 75 and 100 mm) and the addition of polyvinyl acetate(PVAc) emulsion in the corner block attactment to side rail had the effect on raising the usable strength of CBA joint with remarkable high significance. And the effect of 2 - anchor bolts was also superior to that of 1 - bolt significantly. However. the thickness of side rail(22 mm vs. 25 mm) had no effect on the strengthening the table joint rigidity. Mitered type corner block joint appeared to he recommendable for CBA jointed table construction rather than the rectangular type one regardless of the method of block attachment to side rail. The best result identified from Duncan's multiple comparison was in the construction with 25 mm thick and 100 mm height of side rail fastened using 2 - anchor bolts in mitered type corner block. But it would be reasonable to use 22 mm thick & 75 mm high side rail and mitered corner block with PVAc emulsion & 2 bolts considering the productivity and production cost down in the MDF furniture manufacturing industries.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.64 no.2
• /
• pp.144-151
• /
• 2019

The establishment rate of foxtail millet seeds is greatly affected by soil environment conditions. To enhance germination viability and stable production of foxtail millet seeds, it is important to select seeds with a high density. Therefore, this study tested the selection of high-quality seeds using salt solution (specific gravity: 1.000, 1.005, 1.010, 1.015, 1.020, 1.025, 1.030, 1.035, and $1.040g\;L^{-1}$) and investigated their germination rates, percentages of emergence, and seeding quality. In this study, three varieties were tested: 'Hwanggeum', 'Samdachal', and 'Kyeongkwan1'. The thousand seed weight of all three varieties increased proportionally with specific gravity. The highest thousand seed weight was observed at the selection with $1.040g\;L^{-1}$ specific gravity, which also had the highest germination rate of 88.3%, 86.7%, and 90.6%, for 'Hwanggeum'; 'Samdachal'; and 'Kyeongkwan1', respectively. The results of seeding quality indicated that higher the specific gravity during selection, the higher were the values of plant growth (plant height, leaf length, stem diameter, root length, root weight, and stem weight). All the three varieties were found to be longer or heavier for seeds selected at the specific gravity of $1.040g\;L^{-1}$. The packing germination viability investigation found that higher the specific gravity for selection of seeds, the higher was the percentage of emergence (PE) and the emergence rate index (ERI). The PE was the highest for seeds selected at $1.040g\;L^{-1}$ specific gravity (85.3, 83.0, and 87.0%), and ERI was also as high as $2.82d^{-1}\;m^{-1}$ or more at $1.040g\;L^{-1}$. Selection of seeds with salt solution resulted in high germination viability of foxtail millet. Therefore, sowing seeds selected at $1.040g\;L^{-1}$ specific gravity is expected to help substantially in increased productivity.