• 한국환경과학회지
• /
• 제9권5호
• /
• pp.389-392
• /
• 2000

In this study a packed tower was selected for the treatment apparatus of $NH_3$ gas produced in industry. Formerly latticework packing has been used in preventive facility of treatment of $NH_3$ gas. However recently metallic Ralu-Pack 250YC. structured packing is usually being used in petrochemical production plant. This study is for the application the packing to the $NH_3$ gas treatment in wet scrubbing process. In Air/water system hydraulic pressure drop dependent of specific liquid load and gas capacity factor was continuous and parallel from graph. The tower height can be determuined by the number of transfer unit and the height of transfer unit influenced on liquid distribution.

• 한국환경과학회지
• /
• 제6권4호
• /
• pp.391-397
• /
• 1997

The study was carried out to demonstrate the superiority of used packing in view of energy saving and efficiency of mass transfer, comparing with conventional packing. The results are as follows : 1. Owing to low Pressure drop under high load. 25mm NSW-ring, pp. can cause energy saving 2. The unique magnitudes of used packing are as follows $C_G$=5.78, m=0.67, n=0.46 3. Used packing can make high efficiency including energy saving because of low pres sure drop per the number of transfer unit. To rate the characteristic of packing, It should be carried out that the measurement of pressure drop per packing height and per the number of transfer unfit. This study demonstrated the superiority of used packing by carring out above experiment and could be used as basic reference for design and predicting efficiency of packing tower which is tilled with same packing.

• Composites Research
• /
• 제34권5호
• /
• pp.330-336
• /
• 2021

알루미나 파우더는 산업용으로 널리 사용되는 소재 중 하나이지만 파우더 패킹 상태에 따라 제품의 강도가 변하는 문제점이 있다. 위 문제해결을 위하여 입자 패킹효율을 높이려는 많은 선행연구들이 수행되었지만, 기존 연구는 밀리미터 스케일의 입자의 충진 특성을 분석한 것이 대부분이므로 마이크로미터 스케일과 물리적 특성이 달라, 그 선행연구 결과를 토대로 마이크로미터 스케일에 적용하기 어렵다. 따라서 본 논문에서는 마이크로미터 스케일의 알루미나 파우더를 이용하여 충진률을 높이기 위하여 통계적방법을 이용하여 3단계 실험을 수행하였다. 먼저, 혼합물시험계획법을 이용하여 충진율이 높은 크기 조합 및 혼합 비율을 선정하였으며, 진동 실험장치에서 가진 주파수 변경에 따른 충진 높이 변화를 분석하여 적정 가진 주파수를 선정하였다. 마지막으로 앞서 언급한 실험 결과값을 토대로 알루미나 파우더 충진율 시험을 수행하였다. 그 결과, 최대 높이 변화량은 충진 크기조합 선정을 위해 수행한 최초의 실험 결과 최댓값보다 42% 향상된 것을 확인하였다.

• Geomechanics and Engineering
• /
• 제18권3호
• /
• pp.315-328
• /
• 2019

This paper presents an investigation on bearing capacity, load-settlement behavior and safety factor of rock-soil slopes reinforced using geogrid-box method (GBM). To this end, small-scale laboratory studies were carried out to study the load-settlement response of a circular footing resting on unreinforced and reinforced rock-soil slopes. Several parameters including unit weight of rock-soil materials (loose- and dense-packing modes), slope height, location of footing relative to the slope crest, and geogrid tensile strength were studied. A series of finite element analysis were conducted using ABAQUS software to predict the bearing capacity behavior of slopes. Limit equilibrium and finite element analysis were also performed using commercially available software SLIDE and ABAQUS, respectively to calculate the safety factor. It was found that stabilization of rock-soil slopes using GBM significantly improves the bearing capacity and settlement behavior of slopes. It was established that, the displacement contours in the dense-packing mode distribute in a broader and deeper area as compared with the loose-packing mode, which results in higher ultimate bearing load. Moreover, it was found that in the loose-packing mode an increase in the vertical pressure load is accompanied with an increase in the soil settlement, while in the dense-packing mode the load-settlement curves show a pronounced peak. Comparison of bearing capacity ratios for the dense- and loose-packing modes demonstrated that the maximum benefit of GBM is achieved for rock-soil slopes in loose-packing mode. It was also found that by increasing the slope height, both the initial stiffness and the bearing load decreases. The results indicated a significant increase in the ultimate bearing load as the distance of the footing to the slope crest increases. For all the cases, a good agreement between the laboratory and numerical results was observed.

• Journal of Advanced Marine Engineering and Technology
• /
• 제15권5호
• /
• pp.23-29
• /
• 1991

Uncertainty is studied in the measurements of average packing density, thickness of packed spheres and transmittance in the experiments to study the effect of the bed height and the existence of the bed side walls on the transmittance of radiative energy through packed spheres. The packing density of the bed is obtained by counting the number of the spheres packed in three pipes with different heights. The bed height of the packed spheres is estimated from the number of spheres contained in the bed by using the relation between the bed height and the sphere number. The transmittance is obtained by dividing the intensity of the transmitted laser beam by the incoming-beam intensity. From the analysis, the uncertainity in the measurements of transmittance is shown to be less than 10.2%(95% coverage).

• Bulletin of the Korean Chemical Society
• /
• 제26권1호
• /
• pp.127-130
• /
• 2005

The early stage of the self assembly for octadecyltrichlorosilane (OTS)-based monolayers is investigated using atomic force microscopy (AFM). Height measurements using AFM prove that the island height of the monolayers gradually increases with increasing the island size, and is close to the limiting value (h = $\sim$25 $\AA$) after d = $\sim$600 nm in size. Since the theoretical length of a covalently bound OTS molecule is 26.2 Å, the limiting value of the island height means that the islands with d ${\geq}$ 600 nm consist of close-packed, fully extended chains. The heights for the islands with d < 600 nm are lower than the limiting value and decrease with decreasing the island sizes. This observation indicates that the OTS molecules in the small islands are less densely packed, and that the packing densities of the islands increase as the islands grow in size.

• 한국안전학회지
• /
• 제14권3호
• /
• pp.101-109
• /
• 1999

This study attempts to analyse the solid mixing in the feeder and the packing effect for pressure fluctuations in the fluidized bed. To study the mixing characteristics of solid in vibrating feeder for the stable operations of fluidized combustion, the system consisted of two groups of particles such that fine particles were located on the top of the coarse particles before vibratory mixing had started. The effects of packing materials on the pressure fluctuations in a fluidized bed were analysed by using a statistical method to interpret the behavior of fluidized bed. The experiments were carried out in a fluidized bed of 6.7cm-ID, and the experimental variables were particle sizes, of 115 to 1,015$\mu\textrm{m}$ in diameter and the multi-sized particles haying Rosin-Rammler and Gaussian distributions. The settled bed heights of particles to diameter ratios (L/D) were ranged from 0.5 to 2.0. And fluidizing of particles was carried out by air. The packing materials used were screen packing, and the properties of the pressure fluctuations in the fluidized bed were measured by a differential pressure transducer. The properties of the pressure fluctuations calculated were the mean, the standard deviation, and the major frequency of the power spectral density functions. From the characteristics of fluidizing, it was found that the standard deviation of pressure fluctuations could be effectively used to explain the fluidized phenomena, and the packing materials affected severely the properties of the pressure fluctuations. As a result, from the interpretation by spectral analysis, the effects of measuring radius of pressure fluctuations on standard deviation were constant in the case of the fluidized bed with and without packing materials. However, the effects of measuring the height of pressure fluctuations on standard deviations were linear increasing for the fluidized bed with packing materials, but were constant for the fluidized bed without packing materials at 4.5cm above the gas distributor. The major frequency of pressure fluctuations was found to be nearly independent of fluidized system. Also, the major frequency of pressure fluctuations decreased with increasing packing size, and it had maximum value at 10% of the packing amount.

• 경영과학
• /
• 제22권1호
• /
• pp.167-178
• /
• 2005

The 2DBPP(Two-Dimensional Bin Packing Problem) is a problem of packing each item into a bin so that no two items overlap and the number of required bins is minimized under the set of rectangular items which may not be rotated and an unlimited number of identical .rectangular bins. The 2DBPP is strongly NP-hard and finds many practical applications in industry. In this paper we discuss a tabu search approach which includes tabu list, intensifying and diversification Strategies. The HNFDH(Hybrid Next Fit Decreasing Height) algorithm is used as an internal algorithm. We find that use of the proper parameter and function such as maximum number of tabu list and space utilization function yields a good solution in a reduced time. We present a tabu search algorithm and its performance through extensive computational experiments.

• 한국생산제조학회지
• /
• 제25권3호
• /
• pp.224-229
• /
• 2016

Recently, polymeric micro-fluidic biochips with numerous micro patterns on the surface were fabricated by injection molding for realizing low-cost mass production of devices. To evaluate the effects of process parameters on large-scale micro-structure replication, a $50{\times}50mm^2$ tool insert with surface structures having a patterns of trapezoidal shapes (height: $30{\mu}m$) was employed. During injection molding, PMMA was used; packing phase parameters and mold temperature were investigated. The replicated surface textures were quantitatively characterized by confocal laser microscopy with 10-nm resolution. The degree of replication at low mold temperatures was found to be higher than that at high mold temperature at the beginning of the packing stage. Thereafter, the degree of replication increased to a greater extent at higher mold temperatures; application of higher mold temperatures improved the degree of replication.

• Korean Chemical Engineering Research
• /
• 제48권5호
• /
• pp.668-671
• /
• 2010

증류시스템 검증용 소형 다단 증류 장치에 활용할 수 있는 소형 충전물을 사용하여 실험실 규모의 증류실험을 실시하였다. 직경 6.7 mm의 실린더형 스테인레스 스틸 충전물을 이용하여 충분한 겉보기 표면적을 얻었고, 액의 체류량과 체류 속도도 양호한 결과를 얻었다. HYSYS를 이용한 이론단수의 계산치와 증류실험치를 비교하여 27 cm 충전층에 대해서는 7 cm이고, 45 cm 충전층에 대해서는 8 cm의 충전층이 이론단 1 단에 해당함을 알았다. 상업용 일정구조 배열의 충전탑에서 8 cm의 충전층이 이론단 1 단에 해당함과 비교하면 유사한 증류효율을 얻을 수 있음을 보여 주었다. 이러한 결과는 증류관의 보온이 완벽할 때 가능하였으며, 실험실에서의 증류 실험에서는 보온이 중요함을 입증하였다. 본 실험 결과로부터 실험실에서도 실제 현장에서 사용하는 증류탑과 유사한 증류 시스템의 시험이 가능함을 보여 준다.