• Journal of Hydrogen and New Energy
• /
• v.26 no.4
• /
• pp.331-338
• /
• 2015

Solar air heaters (SAHs) are simple in design and widely used for solar energy collection devices, and a packed bed is one of typical solar energy storage systems of thermal energy captured by SAHs. This paper presents mathematical modeling and simulation on the thermal performance of various packed bed energy storage systems. A MATLAB program is used to estimate the thermal efficiency of packed bed SAH. Among the various packed bed energy storage systems considered, the wire mesh screen packed bed SAH shows the best thermal efficiency over the entire range of design conditions. The maximum of thermal efficiency of packed bed SAH with wire mesh screen matrices has been found to be 0.794 for Re=2000 - 20000 and ${\Delta}T/I=0.002-0.02$.

• Environmental Engineering Research
• /
• v.25 no.1
• /
• pp.104-113
• /
• 2020

Adsorptive breakthrough modelling is essential for design of a sorption packed bed. In this work, breakthrough modelling of the furfural uptake in bagasse fly ash (BFA) packed bed has been performed. Effect of various parameters like bed height (Z = 15-60 cm), flow rate (Q = 0.02-0.04 L/min) and initial furfural concentration (C_o = 50-200 mg/L) on the breakthrough curve of furfural sorption in a BFA packed bed have been studied. Enhanced breakthrough performance was observed for the higher value of Z, and lower values of C_o and Q. For C_o = 100 mg/L, packed bed operated at Q = 0.03 L/min and Z = 60 cm was found to have lowest adsorbent utilization rate of 5.61 g/L with highest breakthrough volume of 14.67 L. Bed depth service time and Thomas models well represented the experimental data points under all experimental conditions. It can be concluded that BFA can be utilized efficiently in continuous system for the removal of furfural. Overall, more than 99% of furfural was adsorbed in BFA packed bed at experimental conditions.

• Advances in environmental research
• /
• v.12 no.1
• /
• pp.17-40
• /
• 2023

This article presents studies of the adsorption process in a continuous system of fluoride solutions at a concentration of 30 mg/L using a bone char packed in fixed-bed columns, as well as regeneration studies in the same system using HNO₃, HCl and NaOH at 0.01, 0.1 and 1 M. The Thomas Model, Artificial Neural Networks (ANNs), Numerical Integration and Mass Transfer Zone were used for the modeling of asyemmetrical breakthrough curves obtained from the fluoride adsorption on bone char. The maximum adsorption capacity of the breakthrough curves was estimated, and various design parameters of the columns were obtained for the different operating conditions. Results showed that an improvement in the modeling capabilities of the Thomas model can be obtained using ANNs. Moreover, ANNs are useful for determining reasonable and accurate design parameters of packed-bed adsorption columns. This modeling approach can be useful for the process system engineering of dynamic adsorption systems involved in the field of water treatment and purification. It is important to highlight that the obtained results indicate that, when using HCl or HNO₃ at a concentration of 0.1 M, a large number of adsorption-desorption cycles are obtained and, therefore, the highest values of adsorption capacity, which leads to a reduction in operation costs.

• Advances in environmental research
• /
• v.7 no.1
• /
• pp.29-37
• /
• 2018

A simple mathematical model for predicting fixed bed adsorption dynamics is described. The model is characterized by a linear adsorption isotherm and a linear driving force expression for mass transfer. Its analytic solution can be approximated with an algebraic equation in closed form which is easily evaluated by spreadsheet computation. To demonstrate one application of the fixed bed model, a previously published adsorption system is used as a case study in this work. The adsorption system examined here describes chromium breakthrough in a fixed bed adsorber packed with imidazole functionalized adsorbent particles and is characterized by a nonlinear adsorption isotherm. However, the equilibrium behavior of the fixed bed adsorber is in essence governed by a linear adsorption isotherm due to the use of a low influent chromium concentration. It is shown that chromium breakthrough is predicted reasonably well by the fixed bed model. The model's parameters can be easily extracted from independent batch experiments. The proposed modeling approach is very simple and rapid, and only Excel is used for computation.

• 한국연소학회:학술대회논문집
• /
• 2014.11a
• /
• pp.165-166
• /
• 2014

The application of particle reaction model in the packed bed process modeling is discussed for iron ore pellet induration process. Combustion of coke breeze in the pellet is estimated by using shrinking unreacted-core model and grain model in which the progress of chemical reaction is described in different concepts. Under the identical inlet gas and solid conditions, the calculation using shrinking core model showed deviated results in terms of temperature profile and conversion fraction, which may imply the significance of selecting proper particle reaction model in consideration of particle characteristics and process operation conditions.

• Journal of Hydrogen and New Energy
• /
• v.27 no.5
• /
• pp.494-502
• /
• 2016

A 1-dimensional heterogeneous reactor model with the gas-solid interfacial phase gradients was developed for the simulation of the packed bed reactor where the exothermic reversible water gas shift reaction for the natural gas steam reformed gas was proceeding in adiabatic mode. Experimental results obtained over the WGS catalyst, C18-HA, were best simulated when the frequency factor of the reaction rate constant was adjusted to a half the value reported over another WGS catalyst, EX-2248, having the same kinds of active components as the C18-HA. For the reactor of the inside diameter 158.4 mm and the bed length 650 mm, the optimum feeding temperature of the reformed gas was simulated to be $194^{\circ}C$, giving the lowest CO content in the product gas by 1.68 mol% on the basis of dried gas. For reactors more extended in the bed length, the possible lowest CO content in the product gas with the optimum feeding temperature of the reformed gas were suggested.

• Nuclear Engineering and Technology
• /
• v.38 no.4
• /
• pp.383-390
• /
• 2006

Having its roots in medical applications, industrial gamma ray CT has opened up new roads far investigating and modeling industrial processes. Using a line of research related to industrial gamma ray CT, the authors set up a system of single source and detector gamma transmission tomography for wood timber and a packed bed phantom. The hardware of the CT system consists of two servo motors, a data logger, a computer, a radiation source and a radiation detector. One motor simultaneously moves the source and the detector for a parallel beam scanning, whereas the other motor rotates the scan table at a preset projection angle. The image is reconstructed from the measured projections by the filtered back projection method. The phantom was designed to simulate a cross section of a packed bed with a void. The radiation source was 20mCi of Cs-137 and the detector was a 1 inch $\times$ 1 inch NaI (TI) scintillator shielded by a lead collimator. The experimental gamma ray CT image has sufficient resolution to reveal air holes and the density distribution inside the phantom. The system could possibly be applied to a packed bed column or a pipe flow in a petrochemical plant.

• Journal of Hydrogen and New Energy
• /
• v.28 no.5
• /
• pp.453-458
• /
• 2017

A study on the modeling of the methane Chemical Looping Reforming system was carried out. It is aimed to predict the temperature and concentration behavior of the product through modeling of oxygen carrier fixed bed reactors composed of multiple stacks. In order to design the reaction system, first of all, the flow rate of the hydrogen to be produced was calculated. The flow rate ratio of the oxidation/reduction reactor was calculated considering the heat of reaction between adjacent reactors. Finally, in this paper, kinetic model including empirical coefficients was suggested.

• Nuclear Engineering and Technology
• /
• v.55 no.2
• /
• pp.640-647
• /
• 2023

Material corrosion in nuclear power plant (NPP) is not controlled only by amine injection but also by ion exchange (IX) which is the best option to remove trace Na⁺. This study was conducted to understand the Na⁺ leakage characteristics of IX beds packed with ethanolamine-form (ETAH-form) and hydrogen-form (H-form) resins in the simulated water-steam cycle in terms of intrinsic behaviors of four kinds of cation-exchange resins through ASTM test and Vanselow mass action modeling. Na⁺ was inappreciably escaped throughout the channel created in resin layer. Na⁺ leakage from IX bed was non-linearly raised because of its decreasing selectivity with increasing Na⁺ capture and with increasing the fraction of ETAH-form resin. Na⁺ did not reach the breakthrough earlier than ETAH⁺ and NH₄⁺ due to the increased selectivity of Na⁺ to the cation-exchange resin (H⁺ < ETAH⁺ < NH₄⁺ ≪ Na⁺) at the feed composition. Na⁺ leakage from the resin bed filled with small particles was decreased due to the enhanced dynamic IX processes, regardless of its low selectivity. Thus, the particle size is a predominant factor among intrinsic properties of IX resin to reduce Na⁺ leakage from the condensate polishing plant (CPP) in NPPs.

• Journal of the Korean Electrochemical Society
• /
• v.2 no.1
• /
• pp.13-16
• /
• 1999

A mathematical analysis of bipolar electrode reactor model for complex electrochemical reactions could estimate total current from time-concentration data, which coincided well with experimental total current data. Thus behaviour of bipolar electrode reactor could be described by a proposed simulation model. This paper demonstrates how such a model can be used a useful tool in the design for pilot plant experimentation.