• Clean Technology
• /
• v.20 no.2
• /
• pp.154-159
• /
• 2014

In this study, PVC-LMO beads were prepared by immobilizing lithium manganese oxide (LMO) with poly vinyl chloride (PVC) diluted in dimethyl sulfoxide (DMSO) solvent on behalf of N-methyl-2-pyrrolidone (NMP). XRD analysis confirmed that LMO was immobilized well in PVC-LMO beads. The diameter of PVC-LMO beads synthesized by DMSO was about 4 mm. The adsorption experiments of lithium ions by PVC-LMO beads were conducted batchwise. The maximum adsorption capacity obtained from Langmuir model was 21.31 mg/g. The adsorption characteristics of lithium ions by PVC-LMO beads was well described by the pseudo-second-order kinetic model. It was considered that the internal diffusion was the rate controlling step.

• Electrical & Electronic Materials
• /
• v.5 no.2
• /
• pp.237-243
• /
• 1992

무독성 혼합안정제인 Zn/Ca-stearate의 방사선 안정화 효과를 증진시키기 위해서 안정화 조제로 알코올들을 PVC에 배합하여 방사선 조사하였을 때 PVC의 색차변화를 측정하여 이들 안정화 조제의 방사선 안정화 효과를 비교 검토하였다. 2가알코올에 의한 PVC 안정화 효과는 2가알코올의 주쇄길이에 비례하여 나타나고 있으나 sorbitol을 제외한 다가알코올에 의한 PVC 안정화 효과는 거의 없는 것으로 나타났다. 이들 알코올에 의한 PVC의 방사선 안정화는 2가알코올이 PVC에서 발생된 고분자 라디칼에 대한 라디칼 포착제로서 작용하기 때문인 것으로 판단된다.

• Resources Recycling
• /
• v.10 no.6
• /
• pp.3-8
• /
• 2001

This study was examed about leaching behavior in order to separate plasticizer selectively before dechlorination from flexible PVC material in alkali solutions at $80~120^{\circ}C$. The dechlorination of that was not almost occurred below $100^{\circ}C$. But the yield of elution of plasticizer was 100% above 5M NaOH. Therefore, by controlling alkali concentration and reaction temperature, it is possible to extract the plasticizer selectively without taking dechlorination.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.603-608
• /
• 2001

A certain amount of MBS rubber was added to improve toughness of PVC which has a strong tendency of being brittle, producing a mixture, PVC/MBS, from which test specimens were prepared. PVC has strong chemical resistance, oil resistance, frame retardancy and high mechanical strength. Also, it is relatively inexpensive to produce, but shows weakness to impact and difficult for processing. MBS, a typical toughening agent for PVC is generally known, when added in a small amount, to improve impact resistance and to minimize difficulties during the processing of the PVC without adversely affecting the positive aspects of the PVC. In this investigation, attempts were made to observe and determine the variations in elastic and damping constants of the PVC depending on the amounts of MBS added to the mixture, PVC/MBS, and also on the thicknesses of the specimens. An acoustic resonance technique was used for the tests in this investigation. It serves as a method to characterize properties of materials set in vibrational motions, which is initiated by low level stresses generated by externally supplied acoustic energy. Substantial variations were observed in the test results with the addition of the MBS to the PVC. Generally, the magnitudes of elastic constants decrease while the damping capacity improves when MBS rubber was added.

• Polymer(Korea)
• /
• v.24 no.1
• /
• pp.128-132
• /
• 2000

The miscibility between poly(vinyl chloride) (PVC) and polycaprolactone (PCL)-polyamide block copolymer whose content of PCL block is 62.7 wt%, was studied by differential scanning calorimetry. The PCL segment in the block copolymer and PVC has the miscibility showing single glass transition temperature (T$_{g}$). The miscible PVC molecule inhibited the crystallization of PCL segment, making an amorphous homogeneous phase of PCL and PVC segments at high PVC content. The blends had rubber elasticity at the temperature range between the T$_{g}$ of amorphous homogeneous phase of PCL and PVC segments and the melting temperature of polyamide segment, when both phases coexist.ist.

• Resources Recycling
• /
• v.10 no.6
• /
• pp.35-42
• /
• 2001

A study was conducted in order to remove Poly vinyl chloride (PVC) from granular plastic mixture by using Air Table. The motion of plastic particle on Air Table was investigated, and separation test on the plastic mixture with the mixing ratio of PVC 10% and PE 90% was conducted. At the optimum condition obtained from this study, that is frequency of 9.2Hz, air velocity of 1.05 m/sec, End-slope of $7.5 ^{\circ}$, Side-slope of $1^{\circ}$, Feeding speed of 450 g/min, etc., we could separate the PE-PVC mixture to PE (99.96% grade and 98.9% yield) and PVC (88.7% grade and 99.6% yield).

• Journal of Power System Engineering
• /
• v.20 no.5
• /
• pp.72-77
• /
• 2016

The present study investigates noise and condensation characteristics of polyvinyl chloride (PVC), which is widely used for drainage piping materials, complex double structure by comparing to those of PVC single structure piping materials. In addition, effects of insulation on drainage noise has been measured experimentally. As the results of the experiments, noise reduction effect of PVC complex double structure is superior to that of PVC single structure in terms of elbow and vertical piping materials which are employed for drainage pipes of toilet bowls and bathtub. The insulation barely have effect on the noise reduction in case of the PVC single structure since there is almost no changes in noise occurrence even though the insulation is applied on both elbow and vertical piping materials. Temperature differences between inside and outside of the pipes have been measures for the PVC single and complex double structures as well. In consequence, outside temperature of the PVC complex double structure is higher than that of the PVC single structure. The condensation occurrence time of the PVC complex double structure shows a distinct difference from that of the PVC single structure, thus, the PVC complex double structure has outstanding effect on preventing the condensation.

• Elastomers and Composites
• /
• v.30 no.3
• /
• pp.195-206
• /
• 1995

To modify the NBR rubber roll which has poor abrasion and chemical resistance, NBR/PVC blends were prepared in various composition ratios. First of all, their miscibility and vulcanization characteristics were investigated. Their abrasion and chemical resistant properties and physical properties were also studied. DSC thermograms for NBR/PVC blends show only one Tg in the entire composition range, demonstrating a perfect miscibility. In the vulcanization characteristics tested by rheometer, maximum torque decreases as PVC contents increased. In the investigation of physical properties of NBR/PVC blends, hardness increases and elongation decreases along with the increasing contents of PVC. On the other hands, tensile strength increases with the increasing contents of PVC up to 11.1 wt. %, and then decreases with higher contents of PVC. While the abrasion resistance of NBR/PVC blends was similar to that of NBR itself, the chemical resistance of NBR/PVC blends was superior to that of NBR.

• Applied Chemistry for Engineering
• /
• v.26 no.1
• /
• pp.35-39
• /
• 2015

Polyvinylchloride (PVC) thin films having a microporous structure could be prepared by using the solubility difference in solvents. PVC thin film with a water contact angle of $150^{\circ}$ or more was obtained from the PVC solution consisting of the mixture of tetrahydrofuran as a solvent and propanol as a non-solvent. In the drying process of dip-coated PVC film, the increase of drying temperature reduced the tendency of roughened surface, which led the decrease of surface hydrophobicity. As the addition of propanol in the solution with 1 wt% PVC increased, the uniformity of surface roughness was improved. In the case of oxygen plasma treatments, even though the surface structure of PVC thin film was not notably changed, the surface property of the film was changed from the super-hydrophobicity to hydrophilicity as a function of the plasma exposing time.

• Elastomers and Composites
• /
• v.34 no.5
• /
• pp.391-398
• /
• 1999

Di-2-ethyl hexyl phthalate (DOP) and di-2-ethyl hexyl adiphate (DOA) were mixed with poly(vlnvl chlorides) [PVC] which have different degrees of polymerization (DP). Tensile strength, elongation, density, abrasion resistance, and hardness of these compounds were measured, High molecular weight PVC(DP 2500) was superior to that of DP 1300 for tensile strength, Hardness. But elongation and abrasion resistance of P1300 systems were better than those of P2500 systems. The densities of both systems were almost same. On the other hand, DOP Plasticized PVC was superior to DOA plasticized one for tensile strength, elongation, hardness. In cases of density, abrasion resistance, and flexual resistance, DOA systems were better than those of DOP systems.