• Proceedings of the KWS Conference
• /
• 2001.05a
• /
• pp.245-247
• /
• 2001

In this study, the effects of dilution on the wear behavior of PTAW (Plasma Transferred Arc Welding) Inconel 625, Inconel 718 and Stellite 6 overlays on Nimonic 80A were investigated. Inorder to evaluate the wear performance, two-body and three-body abrasive wear test, and dry sliding wear test were performed. According to wear tests, the wear rate of deposit with dilution 30% was higher than that of dilution 10% by 10%, and it was also found the plastic deformation near worn surface.

• Journal of Welding and Joining
• /
• v.22 no.2
• /
• pp.59-68
• /
• 2004

Plasma transferred arc welding (PTAW) has been taken into consideration for repairing Ni-based superalloy components used gas turbine blades. Various cracks has been generally reported to be found in the base metal heat affected zone(HAZ) along grain boundary. Thus, hot cracking susceptibility of Ni-based superalloys was evaluated according to heat treatments. Hot ductility test was conducted on specimens with solution treated at 112$0^{\circ}C$ for 2 hours and aging treated at 845$^{\circ}C$ for 24hours after solution treatment. The results of the hot ductility test appeared that solution treated specimens were the highest ductility recovery rate among three conditions. The loss of ductility at high temperature in Ni-based superalloy was mainly controlled by the degree of pain boundary wetting due to constitutional liquation of MC carbide precipitates. Meanwhile, the highest ductility recovery rate in solution-treated alloys seems to be lack of M23C6, which can be dissolved during heating and then result in the local enrichment of Cr in the vicinity of the grain boundary.

• Journal of Welding and Joining
• /
• v.19 no.5
• /
• pp.540-547
• /
• 2001

This study has evaluated the wear behavior of PTA (Plasma Transferred Arc) Inconel 625 and Stellite 6 overlays on Nimonic 80A substrate. Nimonic 80A alloy was also included for comparison. In order to evaluate the wear performance, three-body abrasive wear test and pin-on-disk dry sliding wear test were performed. Microstructural development during the solidification of deposits is also discussed. Wear test results show that the wear rate of Stellite 6 deposit is lower than that of Inconel 625 deposit and Nimonic 80A. The sliding wear resistance of overlay deposits follows a similar trend to the abrasive wear resistance, but for Nimonic 80A. The main wear mechanisms were abrasive wear for Inconel 625 deposit, adhesive wear and delamination for Stellite 6 deposit in pin-on-disk dry sliding wear test and ploughing in three-body abrasive wear test. Cross sectional examinations of the worn surface of pin specimens after pin-on-disk dry sliding wear test implies that the plastic deformation near worn surface has occurred during the wear testing.

• Journal of Welding and Joining
• /
• v.17 no.5
• /
• pp.107-115
• /
• 1999

The objective of this research was to study the formation of the thick hardened layer with the addition of metal powder(Cu) and ceramics powders(TiC) on the aluminum 5083 alloys by plasma transferred arc process(PTA process) and to characterize the effect of overlaying conditions on the overlaid layer formation. This was followed by investigating the microstructures of the overlaid layers and mechanical properties such as hardness and wear resistance. The overlaid layer containing copper powder was alloyed and intermetallic compound($CuAl_2$) was formed. The overlaid layers with high melting point TiC powders, however, did not react with base metal. Wear resistance of the alloyed layer was remarkably improved by the formation of $CuAl_2$, precipitate phase, which prevented wear of base aluminum alloys and at higher wear speed, accelerated sliding of the counter part. Wear resistance of the composite layer was also remarkably improved because TiC powder act as a load barring element and Fe debris fragments detached from the counter part act as a solid lubricant on the contact surface.

• Journal of Surface Science and Engineering
• /
• v.35 no.4
• /
• pp.241-248
• /
• 2002

Hardfacing layers of Stellite 6 alloy with different molybdenum content are deposited on AISI 1045 carbon steel using plasma transferred arc welding (PTAW). The properties of the hardfacing layer are investigated in order to clarify the effect of molybdenum addition to the cobalt-base alloy. With an increase in molybdenum contents, the size of Cr-rich carbides in the interdendritic region is abruptly refined, but volume fraction of the carbide slightly increases. Also, with an increase of Mo, $M_{6}$ C type carbides are formed instead of Cr-rich $M_{7}$ $C_{3}$ type carbided, and this microstructural change enhanced the mechanical properties of Stellite 6 alloy.

• Journal of Welding and Joining
• /
• v.15 no.5
• /
• pp.92-103
• /
• 1997

The purpose of this study is to improve the wear resistance and hardness of Al alloy by making a formation of the thick surface hardening layers. The thick surface hardening layers were formed by PTAW(Plasma Transferred Arc Welding), with the addition of metal powders (Cu), ceramics powders (NbC, TiC), and mixture powders (Cu+NbC) in Al alloy (A1050, A5083). Mechanical properties of overlaid layers (wear resistance, hardness) were investigated in relation to the microstructure. The results obtained are summarized as follows: The depth of penetration was increased with increasing powder feeding rate. It is considered that these increase were due to the thermal pinch effect by the addition of powders, especially, for the Cu powders, were due to the heat of reaction with the matrix. The hardness and wear resistance of overlaid layers were improved with increasing powder feeding rate. For the Cu powders, it is considered that these increase were due to the increase of the formation of ${\theta}(CuAl_2)$ phase with increasing feeding rate of Cu powers.

• Journal of Welding and Joining
• /
• v.27 no.3
• /
• pp.80-84
• /
• 2009

The Plasma Transferred Arc (PTA) overlay welding method is lately introduced as one of the most useful surface overlay method of the engine component. In this paper, the overlay welding on the SNCrW heat resisting alloy was conducted by the PTA overlay welding process using the super alloy powder. The characteristics of the overlay layers were investigated through the metallurgical and abrasive test. Experimental results showed that the overlay on the SNCrW heat resisting alloy surface was successfully made without hot cracking. The friction wear characteristics of the Co-base Stellite 6 overlayer were most superior. However the abrasive wear characteristics were most inferior in the Co-base Stellite 6 overlayer.

• Proceedings of the KWS Conference
• /
• 2003.05a
• /
• pp.40-42
• /
• 2003

In general, nickel-base superalloy has been extensively used as land-based gas turbine blades and vanes. Plasma transferred arc welding(PTAW) has been considered as a repair welding process of nickel-base superalloy. This research evaluated the relationship between hot ductility behavior and hot cracking susceptibility in nickel-base superalloys. Ductility recovery rate of nickel base superalloys was found to be poor due to incipient melting and constitutional liquation. This seems to increase the hot cracking susceptibility.