• Journal of the Korean Society of Safety
• /
• v.12 no.3
• /
• pp.38-44
• /
• 1997

6063-T5 alloys are tested in laboratory air, water and 3% NaCl solution to investigate the effects of corrosive environment on the retardation behavior through single overload fatigue test. Also, the fatigue crack propagation and the crack closure behavior are studied. The results obtained in this experimental study are summarized as follows. 1) Behaviors of fatigue crack growth retardation are observed in water and 3% NaCl solution as they do in air. The number of delay cycles and the size of affected region by single overload decrease greatly in water and 3% NaCl compared with those in air. 2) In fractographic results, the overload marking by single overload appear remarkably in air, but indistinctly in water and 3% NaCl solution. 3) The effect of crack closure on crack propagation is most remarkable in the beginning of crack propagation. With crack propagation, the crack closure level and its effect decrease greatly.

• Geomechanics and Engineering
• /
• v.8 no.3
• /
• pp.377-390
• /
• 2015

The governing equations of wave propagation in one dimension of elastic continuum materials are investigated by taking the influence of the initial stress into account. After a short review of the theory of elastic wave propagation in a rock mass with an initial stress, results indicate that the initial stress differentially influences P-wave and S-wave propagation. For example, when the initial stress is homogeneous, for the P-wave, the initial stress only affects the magnitude of the elastic coefficients, but for the S-wave, the initial stress not only influences the elastic coefficients but also changes the governing equation of wave propagation. In addition, the P-wave and S-wave velocities were measured for granite samples at a low initial stress state; the results indicate that the seismic velocities increase with the initial stress. The analysis of the previous data of seismic velocities and elastic coefficients in rocks under ultra-high hydrostatic initial stress are also investigated.

• 한국연소학회:학술대회논문집
• /
• 2002.06a
• /
• pp.95-98
• /
• 2002

A numerical investigation on the flame propagation and extinction in a micro combustor is described. Previous measurements of $H_2-air$ flame propagation in a submilimeter scale combustor exhibited significance of wall effects on burning velocity and extinction. The heat transfer to wall becomes important not only in the cooling of burnt gases but also during the flame ropagation, which has be by and large ignored in macro scale combustor calculations. In order to take the heat loss into account the combustion calculation, we developed a numerical code with a heat transfer model that was determined empirically from measured data. PISO algorithm was used for differencing of conservation equations. $H_2-air$ reaction was modeled with 10 species - 16 steps. Comparison with measured data showed good agreement in flame propagation speed. Also the pressure decrease after flame extinction was accurately predicted by the model. A further study is desirable for a better quenching model that can predict the quenching location.

• Journal of KIISE:Software and Applications
• /
• v.30 no.7_8
• /
• pp.696-702
• /
• 2003

This paper presents a static analysis based on set-based framework which estimates exception propagation paths of Java programs, and a visualization tool which visualizes propagation paths of exceptions using the static analysis information. We have implemented the exception propagation analysis and a visualization tool, which can guide programmers to handle exceptions more effectively.

• Journal of the Korean Society for Railway
• /
• v.5 no.1
• /
• pp.26-31
• /
• 2002

The more sophisticated patterns of propagation model is presented in this paper, which includes three different source characteristics (spherical, cosine and dipole). The spherical, cosine and dipole radiation characteristics compared, and sound event level and the maximum sound level are calculated by experiment and calculation. It is shown that patterns of propagation have dipole characteristics for low speed range (below about 150Km/h) at electric multiple system. We know that push-pull high speed system has cosine characteristics of noise propagation at low speed range (below about 200Km/h).

• Journal of Plant Biology
• /
• v.31 no.4
• /
• pp.249-258
• /
• 1988

Changes in starch content and activities of ADPG- and UDPG-starch synthase and $\alpha$- and, $\beta$-amylase were studied in order to investigate effects of gibberellic aicd and abscisic acid on endogenous starch content during shoot differentiation and protocorm propagation in Cymbidium spp. (Jungfrau) protocorm. Shoot differentiation was promoted during the degradation of endogenous starch and protocorn propagation was promoted during starch accumulation in protocorm. The activities of ADPG- and, UDPG-starch synthase and $\alpha$- and $\beta$-amylase seemed to be related with starch content. Shoot differentiation and protocorm propagation were slightly inhibited in protocorm explants treated with 100$\mu$M gibberellic acid. The explants treated with 10$\mu$M abscisic acid lost the capacity for shoot differentiation and protocorm propagation, and that could not be overcome by 100$\mu$M gibberellic acid added to culture medium. Starch content fluctuated as the control even after 10$\mu$M abscisic acid. None the less, the treatment completely inhibited shoot differentiation and protocorm propagation.

• Journal of Positioning, Navigation, and Timing
• /
• v.9 no.3
• /
• pp.157-167
• /
• 2020

Fingerprinting method is useful when estimating the location of a requestor based on LTE signals in an urban area. To do this, it is necessary to acquire location-based signals everywhere in the service area for fingerprint DB generation in advance. However, there may be signal uncollected area within a wide service area, which may cause a problem that the positioning accuracy of the requestor is low. In order to solve this problem, in this paper, signal propagation modeling is performed based on the obtained measurements, and based on this model, the signal information in the non-acquisition region is estimated. To this end, techniques for modeling signal propagation according to a method using measurements are proposed. The performance of the proposed techniques is verified based on the measurements obtained on a test bed selected as Seocho-gu, Seoul. As a result, it can be seen that signal propagation modeling performed based on multidivision segmented measurements has the most performance improvement.

• Structural Engineering and Mechanics
• /
• v.2 no.2
• /
• pp.173-184
• /
• 1994

The objective of this study was to develop a simple and efficient numerical modeling technique for dynamic crack propagation using the finite element method. The study focused on the analysis of a rapidly propagation crack in an elastic body. As already known, discrete crack tip advance with the stationary node procedure results in spurious oscillation in the calculated energy terms. To reduce the spurious oscillation, a simple and efficient moving node procedure is proposed. The procedure does require neither remeshing the discretization nor distorting the original mesh. Two different central difference schemes are also evaluated and compared for dynamic crack propagation problem.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.8 no.4
• /
• pp.67-73
• /
• 2008

In the Markov network which models disparity map with the Markov Random Field(MRF), the belief propagation algorithm is operated by message passing between nodes corresponding to each pixels. Belief propagation algorithm required much iteration for accurate result. In this paper, we propose the stereo matching algorithm using belief propagation in multi-resolution domain. Multi-resolution method based on wavelet or lifting can reduce the search area, therefore this algorithm can generate disparity map with fast speed.

• The Transactions of the Korea Information Processing Society
• /
• v.7 no.8
• /
• pp.2520-2527
• /
• 2000

An improved transition density propagation method for power estimation is proposed. The power estimation for the zero delay model is a proper criteria for the.lower boutldlIry for power consumption. A transition propagation method, including the zero delay model as a lower boundary for power stimation was studied. However, there were some redundancy factors in the process of transition density propagation. Hence this paper will explore the transition density propagation behavior to eliminate the redundancy factors and present theirriprQved estimation methodology for the signal transition density. The experiments show that the proposed method has comparably better estimation accuracy than the conventional methods.