• Bulletin of the Korean Chemical Society
• /
• 제32권2호
• /
• pp.559-565
• /
• 2011

The following noble series of statistical copolymers, poly[(2-(3-thienyl)ethanol n-butoxycarbonylmethylurethane)-co-3-hexylthiophene] (PURET-co-P3HT), were synthesized by the chemical dehydrogenation method using anhydrous $FeCl_3$. The structure and electro-optical properties of these copolymers were characterized using $^1H$-NMR, UV-visible spectroscopy, elemental analysis, GPC, DSC, TGA, photoluminescence (PL), and cyclic voltammetry (CV). The statistical copolymers, PURET-co-P3HT (1:0, 2:1, 1:1, 1:2, 1:3), were soluble in common organic solvents and easily spin coated onto indium-tin oxide (ITO) coated glass substrates. Hybrid bulk heterojunction photovoltaic cells with an ITO/G-PEDOT/PURET-co-P3HT:PCBM:Ag nanowires/$TiO_x$/Al configuration were fabricated, and the photovoltaic cells using PURET-co-P3HT (1:2) showed the best photovoltaic performance compared with those using PURET-co-P3HT (1:0, 2:1, 1:1, 1:3). The optimal hybrid bulk heterojunction photovoltaic cell exhibits a power conversion efficiency (PCE) of 1.58% ($V_{oc}$ = 0.82 V, $J_{sc}$ = 5.58, FF = 0.35) with PURET-co-P3HT (1:2) measured by using an AM 1.5 G irradiation (100 mW/$cm^2$) on an Oriel Xenon solar simulator (Oriel 300 W).

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.343-343
• /
• 2014

We reported on the electrical, optical, structural and morphological properties fabricated by co-sputtering for use as an anode for organic solar cells (OSCs). By adjusting RF and DC power of $MoO_3$ and IZO targets during co-sputtering, we fabricated the $MoO_3$-IZO electrode with graded content of the $MoO_3$ on the IZO films. At optimized $MoO_3$ thickness of 20 nm, the $MoO_3$ graded IZO electrode showed a higher mobility ($33cm^2/V-Sec$) than directly deposited $MoO_3$ on IZO film ($26cm^2/V-Sec$). At visible range (400nm~800nm), optical transmittance of the $MoO_3$ graded IZO electrode is higher than that of directly deposited $MoO_3$ on IZO film. High mobility of $MoO_3$ graded on IZO is attributed to less interface scattering between $MoO_3$ and IZO. To investigate the feasibility of $MoO_3$ graded IZO films, we fabricated conventional P3HT:PCBM based OSCs with $MoO_3$ graded IZO as a function of MoO3 thickness. The OSC fabricated on the $MoO_3$ graded IZO anode showed a fill factor of 66.53%, a short circuit current of $8.121mA/cm^2$, an open circuit voltage of 0.592 V, and a power conversion efficiency of 3.2% comparable to OSC fabricated on ITO anode and higher than directly deposited $MoO_3$ on IZO film. We suggested possible mechanism to explain the high performance of OSCs with a $MoO_3$ graded IZO.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.257.1-257.1
• /
• 2014

We investigated characteristics of ITO/Ag-Pd-Cu (APC)/ITO multilayer electrodes prepared by direct current magnetron sputtering for use as an anode in organic solar cells (OSCs). To optimize electrical properties of ITO/APC/ITO multilayer, we fabricated the ITO/APC/ITO multilayer at a fixed ITO thickness of 30 nm as a function of APC thickness. Compare to the surface of Ag layer on ITO, the APC had a smooth surface morphology. At optimized APC thickness of 12 nm, the ITO/APC/ITO multilayer exhibited a sheet resistance of $6{\Omega}/square$ and optical transmittance of 84.15% at a wavelength of 550 nm which is comparable to conventional ITO/Ag/ITO multilayer. However, the APC-based ITO multilayer showed a higher average transmittance in a visible region than the Ag-based ITO multilayer. The higher average transmittance of ITO/APC/ITO multilayer indicated the multilayer is suitable anode for organic solar cells with P3HT:PCBM active layer. OSCs fabricated on the optimized ITO/ACP/ITO multilayer exhibited a better performance with a fill factor of 64.815%, a short circuit current of $8.107mA/cm^2$, an open circuit voltage of 0.59 V, and power conversion efficiency (3.101%) than OSC with ITO/Ag/ITO multilayer (2.8%).

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.238-239
• /
• 2010

Dimethyl sulphoxide (DMSO) is one of the widely-used secondary dopants in order to enhance the conductivity of poly(3, 4-ethylenedioxy-thiophene):poly(styrene sulfonate) (PEDOT:PSS) film. In this work, we investigated the effect of DMSO doping in to PEDOT:PSS on the electrical performance of the bulk heterojunction photovoltaics consisting of poly(3-hexylthiophene-2, 5-diyl) and phenyl-C61-butyric acid methyl ester. Correlation between the power conversion efficiency and the mechanism of improving conductivity, surface morphology, and contact properties was examined. The PEDOT:PSS films, which contain different concentration of DMSO, have been prepared and annealed at different annealing temperatures. The mixture of DMSO and PEDOT:PSS was prepared with a ratio of 1%, 5%, 15%, 25%, 35%, 45%, 55% by volume of DMSO, respectively. The DMSO-contained PEDOT:PSS solutions were stirred for 1hr at $40^{\circ}C$, then spin-coated on the ultra-sonicated glass. The spin-coated films were baked for 10min at $65^{\circ}C$, $85^{\circ}C$, and $120^{\circ}C$ in air. In order to investigate the electrical performance, P3HT:PCBM blended film was deposited with thickness of 150nm on DMSO-doped PEDOT:PSS layer. After depositing 100nm of Al, the device was post-annealed for 30min at $120^{\circ}C$ in vacuum. The fabricated cells, in this study, have been characterized by using several techniques such as UV-Visible spectrum, 4-point probe, J-V characteristics, and atomic force microscopy (AFM). The power conversion efficiency (AM 1.5G conditions) was increased from 0.91% to 2.35% by tuning DMSO doping ratio and annealing temperature. It is believed that the improved power conversion efficiency of the photovoltaics is attributed to the increased conductivity, leading to increasing short-circuit current in DMSO-doped PEDOT:PSS layer.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.217-217
• /
• 2012

Solution-processed tungsten oxide thin film with thickness of about 30 nm is prepared from ammonium tungstate. This layer is introduced into the interface between the poly(3-hexylthiophene):[6,6]-phenyl-C61-butyric acid methyl ester (P3HT:PCBM) layer and the ITO electrode to be used as an electron blocking layer. The annealed tungsten oxide thin films at $150^{\circ}C$ and $300^{\circ}C$ show amorphous phase, while the $400^{\circ}C$ -annealed tungsten oxide film shows crystalline phase. At $150^{\circ}C$ annealing temperature, the conversion efficiency is significantly improved from 0.71% to 1.42% as the condition is changed from vacuum to air atmosphere, which is related to oxidation state of tungsten in amorphous phase. For the air annealing condition, the conversion efficiency is further increased from 1.42% to 2.01% as the temperature is increased from $150^{\circ}C$ to $300^{\circ}C$, which is mainly due to the removal of the chemisorbed water. However, a slight deterioration in photovoltaic performance is observed when the temperature is increased to $400^{\circ}C$, which is ascribed to poor electron blocking ability due to the formation of crystalline phase. It is concluded that $W^{6+}$ oxidation state and amorphous nature in tungsten oxide interlayer is essential for blocking electron effectively from the active layer to the ITO electrode.

• Bulletin of the Korean Chemical Society
• /
• 제35권10호
• /
• pp.2963-2968
• /
• 2014

We report synthesis and photovoltaic properties of two new conjugated copolymers, PCPDTQxF and PDTSQxF, with 6,7-difluoro-2,3-dihexylquinoxaline unit prepared by Stille coupling reaction. The advantage of 6,7-difluoro-2,3-dihexylquinoxaline based copolymer are high PCEs due to lower HOMO energy level, long wavelength absorption and high hole mobility. The solid films of PCPDTQxF and PDTSQxF showed absorption bands with maximum peaks at about 623 and 493 nm and the absorption onsets at 711 and 635 nm, corresponding to band gaps of 1.74 and 1.95 eV, respectively. The oxidation onsets of the PCPDTQxF and PDTSQxF polymers were estimated to be 0.68 and 0.95 V, which correspond to HOMO energy levels of -5.48 and -5.75 eV, respectively. The PDTSQxF has lower HOMO energy level as compared to PCPDTQxF to lead higher $V_{OC}$ value. The device comprising PCPDTQxF:PCBM (1:2) dissolved to a concentration of 1 wt % in ODCB showed $V_{OC}$ value of 0.62 V, $J_{SC}$ value of $1.14mA/cm^2$, and FF of 0.35, which yielded PCE of 0.25%.

• Bulletin of the Korean Chemical Society
• /
• 제35권2호
• /
• pp.569-574
• /
• 2014

Inverted bulk hetero-junction polymer solar cells (iPSC) composed of P3HT/PC61BM blends on the ZnO modified with benzoic acid derivatives-based self-assembled monolayers (SAM) are fabricated. Compared with the device using the pristine ZnO, the devices with ZnO surface modified SAMs derived from benzoic acid such as 4-(diphenylamino)benzoic acid (DPA-BA) and 4-(9H-carbazol-9-yl)benzoic acid (Cz-BA) as an electron transporting layer show improved the performances. It is mainly attributed to the favorable interface dipole at the interface between ZnO and the active layer, the eective passivation of the ZnO surface traps, decrease of the work function and facilitating transport of electron from PCBM to ITO electrode. The power conversion eciency (PCE) of iPSCs based on DPA-BA and Cz-BA treated ZnO reaches 2.78 and 2.88%, respectively, while the PCE of the device based on untreated ZnO is 2.49%. The open circuit voltage values ($V_{oc}$) of the devices with bare ZnO and SAM treated ZnO are not much different. Whereas, higher the fill factor (FF) and lower the series resistance ($R_s$) are obtained in the devices with SAMs modification.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.131-131
• /
• 2010

We compared the electrical, optical, structural, and interface properties of indium zinc oxide (IZO)-Ag-IZO and IZO-Au-IZO multilayer electrodes deposited by linear facing target sputtering system at room temperature for organic photovoltaics. The IZO-Ag-IZO and IZO-Au-IZO multilayer electrodes show a significant reduction in their sheet resistance (4.15 and 5.49 Ohm/square) and resistivity ($3.9{\times}10^{-5}$ and $5.5{\times}10^{-5}$Ohm-cm) with increasing thickness of the Ag and Au layers, respectively. In spite of its similar electrical properties, the optical transmittance of the IZO-Ag-IZO electrode is much higher than that of the IZO-Au-IZO electrode, due to the more effective antireflection effect of Ag than Au in the visible region. In addition, the Auger electron spectroscopy depth profile results for the IZO/Ag/IZO and IZO/Au/IZO multilayer electrodes showed no interfacial reaction between the IZO layer and Ag or Au layer, due to the low preparation temperature. To investigate in detail the Ag and Au structures on the bottom IZO electrode with increasing thickness, a synchrotron x-ray scattering examination was employed. Moreover, the OSC fabricated on the IZO-Ag-IZO electrode shows a higher power conversion efficiency (3.05%) than the OSC prepared on the IZO-Au-IZO electrode (2.66%), due to its high optical transmittance in the wavelength range of 400-600 nm, which is the absorption wavelength of the P3HT:PCBM active layer.

• 공업화학
• /
• 제22권1호
• /
• pp.15-20
• /
• 2011

2,3-Dimethyl-5,8-dithiophen-2-yl-quinoxaline을 기본 골격으로 한 poly[2,3-dimethyl-5,8-dithiophene-2-yl-quinoxaline-alt-9,9-dihexyl-9H-fluorene] (PFTQT)과 poly[2,3-dimethyl-5,8-dithiophene-2-yl-quinoxaline-alt-10-hexyl-10H-phenothiazine] (PPTTQT)을 Suzuki coupling법을 이용하여 중합 하였다. 합성된 고분자들은 chloroform, chlorobenzene, o-dichlorobenzene, tetrahydrofuran (THF), toluene과 같은 유기용매에 대한 용해도가 우수하였고, PFTQT의 최대흡수파장과 밴드 갭은 각각 440 nm와 2.30 eV이고, PPTTQT의 경우는 각각 445 nm와 2.23 eV이었다. PFTQT의 HOMO 및 LUMO 에너지준위는 -6.05와 -3.75 eV이고, PPTTQT의 경우는 각각 -5.89와 -3.66 eV이었다. 합성된 고분자들과 전자 받개 물질인 (6)-1-(3-(methoxycarbonyl)-{5}-1-phenyl[5,6]-fullerene (PCBM)을 1 : 2의 중량비로 블렌딩하여 제작한 태양전지의 효율은 AM (air mass) 1.5 G, 1 sun 조건($100mA/cm^2$)에서 PFTQT는 0.24%, PPTTQT의 경우는 0.16%로 측정되었다. 그리고 소자의 단락전류 밀도($J_{sc}$), FF (fill factor)와 개방전압($V_{oc}$)은 PFTQT의 경우 각각 $0.97mA/cm^2$, 29%, 0.86 V이며, PPTTQT의 경우 각각 $0.80mA/cm^2$, 28%, 0.71 V이었다.