• Tribology and Lubricants
• /
• v.35 no.1
• /
• pp.1-8
• /
• 2019

Demand for plastic gears are increasing in many industries due to their low production cost, light weight, applicability without lubricant, corrosion resistance and high resilience. Despite these benefits, utilizing plastic gears is limited due to their poor material properties. In this work, DLC coating was applied to improve the tribological properties of polyamide66 gear. 0 V, 40 V, and 70 V of negative bias voltages were selected as a deposition parameter in DC magnetron sputtering system. Pin-on-disk experiment was performed in order to investigate the wear characteristics of the gears. The results of the pin-on-disk experiment showed that DLC coated polyamide66 with 40 V of negative bias voltage had the lowest friction coefficient value (0.134) and DLC coated PA66 with 0 V of negative bias voltage showed the best wear resistance ($9.83{\times}10^{-10}mm^3/N{\cdot}mm$) among all the specimens. Based on these results, durability tests were conducted for DLC coated polyamide66 gears with 0 V of negative bias voltage. The tests showed that the temperature of the uncoated polyamide66 gear increased to about $37^{\circ}C$ while the DLC coated gear saturated at about $25^{\circ}C$. Also, the power transmission efficiency of the DLC coated gear increased by about 6% compared to those without coating. Weight loss of the polyamide66 gears were reduced by about 73%.

• Design & Manufacturing
• /
• v.17 no.3
• /
• pp.55-60
• /
• 2023

The fiber-reinforced plastics and cellular injection molding process can be used to efficiently reduce the weight of battery housing components of mild hybrid electronic vehicles(MHEV) made of metal. However, the fiber orientation of fiber-reinforced plastics and the growth of foaming cells are intertwined during the injection molding process, so it is difficult to predict the mechanical properties of products in the design process. Therefore, it is necessary to evaluate the mechanical properties of the materials prior to the efficient stiffness design of the target product. In this study, a study was conducted to evaluated the mechanical properties of fiber reinforced cellular injection-molded specimens. Two types of fiber-reinforced plastics that can be used in the target product were evaluated for changes in tensile properties of cellular injection-molded specimens depending on the foaming ratio and position from the injection gate. The PP and PA66 specimens showed a decrease of tensile modulus and strength of approximately 30% and 17% depending on the foaming ratio, respectively. Also, the tensile strength decreased approximately 26% and 17% depending on the position from the injection gate, respectively. As a result, it was confirmed that the PP specimens have a significantly mechanical property degradation compared to the PA66 specimens depending on the foaming ratio and position.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.6
• /
• pp.878-887
• /
• 2020

A neutral extract (NE), that is soluble in cold water and has excellent antioxidant activity, from Pinus radiata pine bark was prepared by sodium bicarbonate treatment, and its chemical characteristics were investigated. NE was prepared by treating P. radiata bark with 0.8% NaHCO₃ aqueous solution with a 5 : 1 liquor-to-bark ratio at boiling temperature for 1 h, resulting in 44% yield and final pH of 6.66. The yield of NE was 11% higher than that of the hot water extract (HWE) due to the increase in the solubility of polyphenols, the main component in the bark, by NaHCO₃ treatment. NE was characterized through FT-IR, NMR, and MALDI TOF MS analyses. The results indicated that NE is mostly composed of proanthocyanidins (PAs) consisting of procyanidin (PC) units. The acetylated neutral extract (Ac-NE) had weight average molecular weight (${\bar{M}}w$) of 5,300 Da. The Ac-NE had wide molecular weight distribution and its polydispersity (${\bar{M}}w/{\bar{M}}n$) was 6 times higher than that of pure PA. The antioxidant activity of NE was determined by 2-diphenyl-1-picrylhydrazyl (DPPH) free radical scavenging assay and showed that NE had comparable antioxidant activity with pure PA.

• Journal of Chest Surgery
• /
• v.24 no.10
• /
• pp.960-966
• /
• 1991

From February 1984 through July 1991, 104 infants less than 1 year of age with congenital heart defects underwent open heart repair with conventional cardiopulmonary bypass which occupied 10.7% of all patients with congenital heart defects operated on during same period. There were 66 boys and 38 girls 7 days to 12 months [mean age, 8.2 months]. Four patients were neonates, 8 were 1 to 3 months, 23 were 4 to 6 months, and 69 were 7 to 12 months of age. Mean body weight at repair was 6.9kg and mean BSA, 0.36m2 Indications for operation were intractable congestive heart failure and severe pulmonary hypertension in patients with VSD and severe cyanosis and anoxic spells in patients with TOF. Conditions corrected were VSD[79], TOF[8], AVSD[4], PS[2], PA+IVS[2], TAPVC [2], MR[2], DOLV[l], Truncus arteriosus[1], D-TGA[1], and PA-VSD[1]. Twenty-three of 79 patients with VSD had associated cardiovascular anomalies which included PDA in 16 patients, PS in 9 patients, ASD in 5 patients, LSVC in 2 patients, MR in 1 patient, dextrocardia in 1 patient, and single coronary artery in 1 patient. The hospital mortality rate was 24.0% which was much higher than that of 6% in patients over 1 year of age. The greatest mortality occurred in babies of low weight under 6 months of age, There was no late death. Surviving infants showed marked symptomatic improvement and change in growth patterns. These surgical results were to be overcome with proper pre- and post-operative management and improvement of surgical technique

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.1
• /
• pp.58-66
• /
• 2016

This study was performed to investigate drying characteristics and quality properties of dried persimmon with vacuum drying process. Drying characteristic curve of the dried persimmon showed that the constant rate drying period and falling rate drying period exist definitely. $_{\circ}Brix$, sugar content and hardness value of the dried persimmon increased as the vacuum pressure and heating temperature increased, but L value of the dried persimmon lower. The results indicated that the optimal conditions were at vacuum pressure of 40~50kPa abs., heating temperature of $30^{\circ}C$ and drying time of 3~4days.

• Journal of the Korean Solar Energy Society
• /
• v.33 no.3
• /
• pp.58-66
• /
• 2013

Recently, PV module that the most important part of the photovoltaic system is more widened to lower manufacturing costs for module. However, the broad PV module results to the serious mechanical damage corning from installation circumstances such as snow, wind etc of snow and finally lead to the dramatic degradation of the electrical behavior of PV module. In this paper, 3 kinds of PV modules that consist of the different thickness and area of front glass and the diverse cross sectional structures of the frame are prepared for this experiment. The drooped length and electrical outputs of the PV modules are measured by means of applying 600Pa mechanical load to the PV modules from 1200Pa to 5400Pa base on the mechanical load test procedure of K SC IEG 61215 standard. The simulation data are obtained by the simulation tool as ANSYS and those are validate by comparing with the those experimental results figure out relations between the deformation and the constituent part of PV module.

• Membrane Journal
• /
• v.11 no.2
• /
• pp.66-73
• /
• 2001

Ivlain objectives of this work arc to investigate basic fouling characteristics and emxts of backpulsing on the fouJing control in the free-end membrane module uo

• Journal of the Korean earth science society
• /
• v.32 no.4
• /
• pp.388-401
• /
• 2011

Asian dust was observed a total of 66 times in the springtime during the period from 2002 to 2010, with 26 cases in March, 23 cases in April and 17 cases in May. This study investigates a Asian dust episode that occurred during the period from 22 to 25 May 2010, based on synoptic weather patterns, wind vector at 850 hPa, relative humidity at 1000 hPa, Jet streams and wind vector at 300 hPa, PM10 concentration in Korea and satellite imagery. In this case, Asian dust originated on 22 May along the rear of a developing low pressure system in Mongolia. The Asian dust was then transported southeastward and bypassed the Korea peninsula from 23 to 24 May, before reaching Japan on 25 May. Jet streams on 24 May bypassed the Korean peninsula and induced the development of a surface low pressure centered over the peninsula. The resulting air flow was critical to the trajectory of the Asian dust, which likewise bypassed the Korean peninsula. 72-hour backward trajectory data reveal that the Shandong Peninsula and the East China Sea were the points of origin for the air flows that swept through the Japanese sites where Asian dust was observable to the naked eay. The Asian dust pathway is ascertained by horizontal distribution of the Asian dust of RGB imagery from MODIS satellites which captured the Asian dust moving over the Shandong Peninsula, the East China Sea, and northwest of the Kyushu region in Japan. Since the synoptic pattern and the transport way of the Asian dust case are far from typical ones, which Asian dust forecasting technique has long been based on, this study can be good example of exceptional Asian dust pattern and it will be used for more accurate Asian dust forecasting.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.3
• /
• pp.144-149
• /
• 2016

The metal-impregnated activated carbon was produced from bamboo activated carbon by soaking method of metal nitrate solution. The carbonization and activation of raw material was conducted at $900^{\circ}C$. The specific surface area and pore size distribution of the prepared activated carbons were measured. Also, NO and activated carbon reaction were conducted in a thermogravimetric analyzer in order to use as de-NOx agents of used activated carbon. Carbon-NO reactions were carried out with respect to reaction temperature ($20^{\circ}C{\sim}850^{\circ}C$) and NO gas partial pressure (0.1 kPa~1.8 kPa). As results, the specific volume and surface area of bamboo activated carbon impregnated with copper were decreased with increasing Cu amounts of activated carbon. In NO reaction, the reaction rate of Cu impregnated bamboo activated carbon[BA(Cu)] was promoted to compare with that of bamboo activated carbon[BA]. But the reaction rate of Ag impregnated bamboo activated carbon[BA(Ag)] was retarded. Measured reaction orders of NO concentration and activation energy were 0.63[BA], 0.92[BA(Cu)], and 80.5 kJ/mol[BA], 48.5 kJ/mol[BA(Cu)], 66.4 kJ/mol[BA(Ag)], respectively.

• Journal of the East Asian Society of Dietary Life
• /
• v.22 no.2
• /
• pp.271-277
• /
• 2012

Ten green leafy vegetables were cultivated from medicinal plant seed. Their nutritional content, taste, appearance and texture were evaluated. Moisture content was $91.23{\pm}0.00%$ in $Saururus$ $chinensis$ (Sc), $90.39{\pm}0.05%$ in $Perilla$ $frutescens$ (Pa) and $66.78{\pm}0.05%$ in $Agastache$ $rugosa$ (Ar). The fat content was 8.89% in $Salvia$ $plebeia$ (Sp) and 0.13% in $Peucedanum$ $japonicum$ (Pj). The protein content was $11.1{\pm}0.00%$ in Ar and $0.54{\pm}0.03%$ in Pj. Total sugar content was $20.06{\pm}0.03%$ in $Geum$ $japonicum$ (Gj), $12.73{\pm}0.03%$ in $Coixlacry$ $majobi$ (Cm) and $1.04{\pm}0.03%$ in $Atractylodes$ $japonica$ (Aj). Medicinal leafy vegetables had higher glucose, sucrose and fructose, but lower maltose. Ascorbic acid content was $33.67{\pm}1.40$ mg% in Sc, $27.91{\pm}2.91$ mg% in Pa and $15.68{\pm}1.09$ mg% in At. Chlorophyll content was higher in $Perilla$ $frutescens$ var. $acuta$ Kudo than other leafy vegetables. The evaluation also showed that Cm, Pa and Aj tasted sweeter and had low acidity.