• Neonatal Medicine
• /
• 제18권2호
• /
• pp.320-327
• /
• 2011

목적: 조산아는 산화 방지 시스템이 미성숙하여 과산소증 및 저산소증에 노출되면 이차적으로 중추 신경계, 호흡계, 혈액계 등 다른 체내 기관에 손상이 올 수 있다. 저자들은 1,500 g 미만 또는 32주 미만의 조산아에서 동맥혈 산소 분압을 50-70mmHg근처로 유지하기 위하여 경피적 산소 포화도를 90-94%로 유지하여 과산소증 및 저산소증을 회피하는 전략 하에 치료하였던 군(T)과 고식적인 경피적 산소 포화도 감시를 하였던 군(C)에서 사망률, 입원 기간 및 이환율에 대해 비교하였다. 방법: 충남대학교병원 신생아 집중치료실에 입원하였던 신생아 중 1,500 g 미만 또는 32주 미만의 조산아를 대상으로 하였다. 2008년 8월부터 2010년 7월까지 경피적 산소포화도를 90-94%으로 유지하였던 조산아들을 T군으로 하였고 2007년 1월에서 2008년 8월까지 경피적 산소 포화도 감시의 지침 없이 고식적인 관리를 하였던 조산아들을 C군으로 하였다. 양 군 간에 입원 중 사망률, 입원기간, 만성폐질환으로 이행 및 치료 여부, 괴사성 장염, 미숙아 망막증, 뇌실 내 출혈, 동맥관 개존증 등을 후향적으로 비교하였다. 결과: 양 군의 기본 특징은 성별 외에 유의한 차이가 없었다. 사망률은 T군에서 C 군 보다 적은 경향은 보였으나 통계적 유의성은 없었다(5.3% vs. 16.7%, P=0.127). 두 군간에 입원기간, 만성폐질환, 산소 사용 기간과 괴사성 장염의 빈도는 차이가 없었다. ICROP 제 3기 이상의 중증 미숙아 망막증은 T군이 C군 보다 적은 경향을 보였으며(2.6% vs. 10%, P=0.203), 뇌실 내 출혈의 발생 빈도는 T군에서 C군 보다 낮은 경향을 보였다(18.4% vs. 40.0%, P=0.051). 치료가 필요하였던 동맥관 개존증의 빈도는 양 군에서 차이가 없었다. 결론: 극소 저체중 출생아 또는 극소 조산아에서 경피적 산소포화도를 90-94%으로 유지하는 전략은 과산소증 및 잠재적인 저산소증에의 노출을 최소화함으로서 합병증의 증가 없이 단기적 예후 개선에 기여할 수 있을 것이다.

• Journal of Biosystems Engineering
• /
• 제1권1호
• /
• pp.15-15
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic?iency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet?ween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr?ease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$$$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea?ses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin?ear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num?ber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco?very rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• 한국식품위생안전성학회지
• /
• 제31권3호
• /
• pp.186-193
• /
• 2016

Oxathiapiprolin은 병원균의 포자형성과 효모성장을 저해하여 노균병을 방제하는 piperidinyl thiazole isoxazoline 계열 살균제로 2015년 국내 사용등록이 요청된 신규약제이다. 본 연구에서는 oxathiapiprolin의 신규등록과 관련해 안전관리를 위한 공정시험법 마련이 요구되어 농산물 중 잔류분석법을 개발하였다. 농산물 중 oxathiapiprolin은 acetonitrile로 추출한 뒤 분배효율 향상을 위해 1 N sodium hydroxide (NaOH)를 이용해 염기성으로 조절하여 비해리 상태로 만든 뒤 dichloromethane으로 액액분배하였으며 분배추출액은 silica SPE 카트리지로 정제한 뒤 HPLC-UVD로 분석하였다. 개발된 분석법의 검출한계(LOD) 및 정량한계(LOQ)는 각각 0.003, 0.01 mg/kg이었고, 대표농산물 5종(고추, 감귤, 감자, 대두, 현미) 중 oxathiapiprolin의 평균 회수율은 86.7-112.7%(상대표준편차, $RSD{\leq}10%$)으로 나타났다. 이는 잔류물 분석에 관한 CODEX 가이드라인(CAC/GL 40)을 만족하는 것으로 확인되었다. 따라서 개발된 분석법은 국내외 유통 농산물 중 oxathiapiprolin의 안전평가를 위한 잔류량 적부 판정에 있어 공정시험법으로 사용되기에 적합할 것으로 판단된다.

• Nuclear Medicine and Molecular Imaging
• /
• 제40권5호
• /
• pp.249-256
• /
• 2006

목적: 대장-직장암에서 간전이 여부를 진단하기 위한 영상 검사 방법으로 기존에는 CT 촬영을 시행하여 왔다. 최근에는 MR 및 FDG PET을 간전이 진단에 적극적으로 활용하고 있는 추세이다. 이에 이 연구에서는 대장-직장암 환자에서 간전이에 대한 FDG PET의 진단적 가치를 MR과 비교하여 보고자 하였다. 대상 및 방법 대장: 직장암으로 확진된 환자들 중에 간전이를 진단 또는 배제하기 위하여 CT 이외에도 MR 및 F-18-FDG PET (conventional PET 및 fusion PET)을 모두 시행한 환자는 26명이었다. 이 연구에서는 26명의 환자들에게서 영상화 된 35개의 병변을 분석의 대상으로 삼고, FDG PET과 MR의 민감도 및 특이도를 간분엽절제술 및 종양절제술을 통해 얻어진 병리소견 및 임상소견 또는 추적 영상 소견을 표준으로 하여 각각 구하였다. FDG PET과 MR은 평균 7일 간격으로 시행되었으며, 두 검사 사이에 치료적 요법을 시행 받은 환자는 한 명도 없었다. 결과: 병리 결과, 35개의 병변 중에서 18개(51.4%)의 병변은 간전이로 판명되었으며, 나머지 17개(48.6%)는 낭종, 지방, 혈관종, 농양, 호산구성농양 등의 양성 병변으로 판명되었다. 35개의 병변 중 MR과 FDG PET의 진단이 일치한 병변은 간전이 17개(94.4%)와 양성 병변 13개(76.5%)로 전체적으로는 85.7%의 일치도를 보였다. FDG PET의 민감도는 94.4% (17/18), 특이도는 94.1% (16/17)였으며 MR의 민감도는 100% (18/18), 특이도는 82.4% (14/17)이었다. MR에서 위양성을 보였던 3개의 병변은 낭종과 호산구성농양이었고, FDG PET에서 위음성을 보였던 1개의 병변은 직경 8 mm의 작은 병변이었다. 직경 10 mm 이하인 병변들만 분석했을 때, 총 20개의 병변에 대하여 FDG PET은 민감도 85.7%(6/7), 특이도 92.3%(12/13), MR은 민감도 100%(7/7), 특이도 76.9%(10/13)를 보였다. 그 외에도 간전이 병변의 평균 maxSUV는 $6.7{\pm}3.8$로 간전이와 양성병변을 최적으로 감별할 수 있는 maxSUV의 cutoff value는 3.1 이었다. (AUC=0.897, p<0.001, 민감도 83.3%, 특이도 94.1%) 결론: FDG PET은 간전이를 진단하는데 MR과 대등한 민감도와 특이도를 보였다. 통계적으로 유의한 차이를 보이지는 않았지만 간전이에 대한 FDG PET의 음성예측도는 MR보다 높았으며, 직경 10 mm 미만의 작은 병변에 대해서도 FDG PET은 우수한 성적을 보였다. 향후 대장암의 간전이 진단에 FDG PET이 유용하게 이용될 것이다.

• 환경위생공학
• /
• 제15권4호
• /
• pp.59-77
• /
• 2000

This study was carried out to investigate on several factors, which contaminative the water quality through the water pipe during feeding water, in 42 largescaled apart-ments(total 84 cases) and assayed the Volatile Organic Compounds(VOCs) and concen-tration of heavy metals that inflow and outflow in reservior water in Jeonnam area(Mokpo, Suncheon, Yeosu) from January 1999 to December 1999. The results obtained were summarized as follows ; 1. The quality of the water pipe composition in the order of frequency in the quality of water pipes were Copper(45.2%)> Zinc(38.9%)> Stainless steel(9.5%)> PVC(4.8%)> PM(2.4%) in observing 42 sites. All of the drain pipes were used the cast iron quality. 2. The result of certification curve from 12 items(17kind) of VOCs was $1.0-4.0{\mu{g}}/{\ell}$ range, a coefficient of correlation was shown 0.99 over. A MDL of each substance range was within $0.1-1.0{\mu{g}}/{\ell}$. 3. The result of the assay, 5 kinds(Viny chloride, Dichloromethane, Ethylbenzene, M,P-xylene, Styrene) of the VOCs of 14 kinds was not detected and the other items were detected slightly. The detection rate of one item and over in total VOCs samples, were 25.9% in inflow and 27.9% in outflow. And frequency of detect in inflow/outflow of THM(Chloroform, Bromodichloro-methane, Dibromochloromethane, Bromoform) were shown higher than 94.1%, 97.0% each stages. It comes to the conclusion that all of the samples were reason able for drinking water standards. 4. The coefficient of correlation were reasonable, it shown 0.999 over in $0.1-1.0{\mu{g}}/{\ell}$ of a measuring range conditions of 4kinds in organic substance(Zn, Cu, Fe, Mn). 5. The results were showed suitability in 78 cases(92.9%) and unsuitability in 6 cases (7.1%), in 84 cases of in organic substances. Compare to inflow stage, mean concentrations of heavy metal, were increased slightly in Zn, Cu, Fe except Mn than outflow stage. The result of the mean concentration in organic substance inflow and outflow in the apartment water tank using Pair-compared T-test, in 95% reliance index, were $0.179mg/{\ell}(0.151-0.307mg/{\ell})$ in Zinc, $0.136mg/{\ell}(0.113-0.230mg/{\ell})$ in Copper, $0.052mg/{\ell}(0.048-0.098mg/{\ell})$ in Fe, and there was a bit growing tendency but there was no differece in Mn. 6. The mean concentration of Copper which used Cu pipe as a water supply pipe in apartment were $0.216mg/{\ell}(0.161-0.338mg/{\ell})$ in case of the Zine pipe were $0.286mg/{\ell}(0.204-0.435mg/{\ell})$. It shows that the detection rate was more higher than the other material used in Cu or Zn as the water supply pipe. We supposed to Cu and Zn substance were gushing out water supply pipe.