• 한국추진공학회지
• /
• 제21권2호
• /
• pp.9-17
• /
• 2017

비정상 충격파 유도연소의 주기적 압력 진동 특성을 연구하기 위하여 DMD 방법을 적용하였다. Lehr의 충격파 유도 연소 실험을 기반으로 수치적인 연구를 수행하였다. Lehr의 실험을 4 수준의 격자를 이용하여 수치적으로 모사하였으며, FFT 결과로부터 430-435 kHz의 주파수가 계산되었다. 실험 결과는 약 425 kHz로 해석 결과와 유사한 것을 확인하였다. FFT 해석에서 도출되지 않은 저주파 특성을 파악하기 위해 dynamic mode decomposition (DMD) 방법을 적용하였다. 여러 가지 모드 주파수가 계산되었고, 연소불안정 평가 인자 중 하나인 damping coefficient를 도출하여 안정/불안정성을 평가하였다.

• Perinatology
• /
• 제29권4호
• /
• pp.159-164
• /
• 2018

Objective: To compare neonatal respiratory morbidity of twins according to birth order related to gestational age and mode of delivery. Methods: We performed the retrospective research of the medical records of 3,224 neonates (1,612 twin pairs) born in a single center from January 2011 to December 2015. Subjects were classified into four gestational age groups: very (<32 weeks), moderate (32-33 weeks), late (34-36 weeks) preterm, and term (${\geq}37weeks$) groups. We investigated clinical characteristics and respiratory morbidity according to birth order related to gestational age group and mode of delivery. Results: We found increased risk of respiratory morbidity in second-born twin than first-born twin (P=0.039). Second-born twin was associated with increased risk of respiratory distress syndrome (RDS) in late preterm group (odds ratio [OR] 2.8, 95% confidence interval [CI] 1.30-5.95), and transient tachypnea of newborn in term group (OR 1.4, 95% CI 1.03-1.81). In vaginal delivery mode, there was no difference of respiratory morbidity between first and second-born twin in each group, but in cases of Cesarean delivery, second-born twin was related with a greater risk of RDS in late preterm group (OR 2.3, 95% CI 1.07-5.09). Birth order and Cesarean section independently increased the risk of RDS (adjusted OR [aOR] 1.69, 95% CI 1.12-2.54; aOR 2.14, 95% CI 1.25-3.66, respectively). Conclusion: Second-born twin and Cesarean delivery are associated with increased risk of RDS, especially in late preterm twins.

• Journal of Korean Society for Atmospheric Environment
• /
• 제21권E1호
• /
• pp.23-35
• /
• 2005

Size distribution of particulate water-soluble ion components was measured at Gosan, Korea using a micro-orifice uniform deposit impactor (MOUDI). Sulfate, ammonium, and nitrate showed peaks in three size ranges; Sulfate and ammonium were of dominant species measured in the fine mode ($D_{p} < 1.8 {\mu}m$). One peak was observed in the condensation mode ($0.218\sim0.532{\mu}m$), and the other peak was obtained in the droplet mode ($0.532\sim1.8{\mu}m$). Considering the fact that the equivalent ratios of ammonium to sulfate ranged from 0.5 to 1.0 in these size ranges, it is inferred that they formed sufficiently neutralized compounds such as ($NH_{4})_{2}SO_{4} and (NH_{4})_{3}H(SO_{4})_{2}$ during the long-range transport of anthropogenic pollutants. On the other hand, nitrate was distributed mainly in the coarse mode ($3.1\sim6.2{\mu}m$) combined with soil and sea salt. Two sets of MOUDI samples were collected in each season. One sample was collected when the concentrations of criteria air pollutants were relatively high, but the other represented relatively clean air quality. The concentrations of sulfate and ammonium particles in droplet mode were the highest in winter and the lowest in summer. When the air quality was bad, the increase of nitrate was observed in the condensation mode ($0.218\sim0.282{\mu}m$). It thus suggests that the nitrate particles were produced through gas phase reaction of nitric acid with ammonia. Chloride depletion was remarkably high in summer due to the high temperature and relative humidity.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1995년도 춘계학술대회 논문집
• /
• pp.1-4
• /
• 1995

The most of conventional ultrasonic transducers are constructed to generate either longitudinal or shear waves, but not both of them. We investigated the mechanism of dual mode transducers that generates both of the longitudinal and shear waves simultaneously with a single PZT element. The study has been aimed to find the desired cut by the examining the piezoelectric properties. Theory predicts that a mixed P/S mode transducer can be constructed using a related Z-cut of a PZT ceramics. We studied the performance of a PZT element as a function of its rotation angle so that its efficiency is optimized to excite the two waves equally strongly. The results are verified by checking the impedance variation of the element with Finite Element Methods, and chocking the wave form by pulse-echo test simulation. Based upon the theory a rotated Z-cut was prepared and a transducer were fabricated. Validity of the theory calculation is verified through the

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.128-133
• /
• 2002

The main obstacle to high track density in HDD is the structural resonances of the suspension. The most critical mode is sway mode and second torsion mode, when a data is read and written. It is common fact that the effect of two modes is smaller when a thickness is bulky. But the stiffness of suspension is smaller, the slider can follow a disk better. Because these two fact are reciprocal, a compromise is needed. So we investigated another method to improve band width without changing of the thickness of suspension but with changing of the shape. In this paper, we use two method - Sensitivity analysis and SIP using ADS. And we obtained the optimized value close to target value.

• 소성∙가공
• /
• 제15권1호
• /
• pp.27-33
• /
• 2006

It is necessary to improve the pattern replication and birefringence in LGP(Light guide panel) for better optical performance. In the present paper, the effects of injection-compression and injection-press mode with normal injection mold on the distribution of transcription of pattern and birefringence were studied. It was found that the values of pattern replication was improved and the birefringence was reduced for the cases of low initial clamping force in injection-compression mode and for the cases of longer mold opening length in injection-press mode, repectively.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.319-321
• /
• 2007

This paper introduces a general overview of the 6000m class deep-sea ROV. Hemire and Henuvy. and then describes its motion control system. It is developed by Korea Ocean Research & Development Institute(KORDI) for 6 years since 2001. sponsored by the Ministry of Maritime Affairs and, Fisheries (MOMAF). Hemire is remotely operated by a fiber optic telemetry. where 6 thrusters are controlled by operator in manual mode and by auto depth control and auto heading control in auto mode. In this paper. operational mechanism of manual and automatic mode with some convenient functions for operator is desc.ribed. Finally, results of sea trial conducted at the Philippine sea where a depth is 5.770m are shown.

• 한국태양에너지학회 논문집
• /
• 제21권1호
• /
• pp.11-20
• /
• 2001

In this paper described common MPPT(Maximum Power Point Tracking) control algorithm; Constant Voltage Control, P&O(Perturbation and Observation), IncCond(Incremental Conductance), and investigated it's efficiency. Through simulation and efficiency evaluation, analyze the steady/transient states characteristics and efficiency of control algorithms respectively. Also, To high-efficiency proposed Two-mode MPPT control for improve on the existing control algorithm. Moreover, this paper suggested a topology for MPPT measuring efficiency and a method of examination.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.1951-1953
• /
• 2005

This paper present a new disk-type piezoelectric transformer. The input side of the transformer has a crescent-shaped electrode and the output side has a focused poling direction. The piezoelectric transformers operated in each transformer's resonance vibration mode. The electrodes and poling directions on commercially available piezoelectric ceramic disks were designed so that the planar or shear mode coupling factor $(k_p,\;k_{15})$ becomes effective rather than the transverse mode coupling factor ($k_{31}$). A single layer prototype transformer, 26[mm] in diameter and $1.5{\sim}4.0[mm]$ thick, was fabricated, such as step-up ratio, power transformation efficiency and temperature were measured.

• 대한치과보철학회지
• /
• 제35권4호
• /
• pp.719-741
• /
• 1997

This study was undertaken to compare by Atomic Force Microscope the effects of various finishing and polishing instruments on surface roughness of filling and veneering composite resins. Seven composite resins were studied : Silux Plus (3M Dental Products, U.S.A.), Charisma (Heraeus Kulzer, Germany), Prisma THP (L.D.Caulk, Dentsply, U.S.A.), Photoclearfil (Kuraray, Japan), Cesead (Kuraray, Japan), Thermoresin LC (GC, Japan), Artglass (Heraeus Kulzer, Germany). Samples were placed and polymerized in holes (2mm thick and 8.5mm in diameter) machined in Teflon mold under glass plate, ensuring excess of material and moulded to shape with polyester matrix strip. Except control group (Polyester matrix strip), all experimental groups were finished and polishied under manufacturer's instructions. The finishing and polishing procedure were : carbide bur (E.T carbide set 4159, Komet, Germany), diamond bur (composite resin polishing bur set, GC, Japan), aluminum-oxide disc (Sof-Lex Pop-On, 3M Dental Products, U.S.A.), diamond-particle disc (Dia-Finish, Renfert Germany), white stone bur & rubber point( composite finishing kit, EDENTA, Swiss), respectively. Each specimens were evaluated for the surface roughness with Atomic Force Microscope (AutoProbe CP, Park Scientific Instruments, U.S.A.) under contact mode and constant height mode. The results as follows : 1. Except Thermoresin LC, all experimental composite resin groups showed more rougher than control group after finishing and polishing(p<0.1). 2. A surface as smooth as control group was obtained by $Al_{2}O_{3}$ disc all filling composite resin groups except Charisma and all veneering composite resin groups except Thermoresin LC(p<0.05). 3. In case of Thermoresin LC, there were no statistically significant differences before and after finishing and polishing(p>0.1). 4. Carbide bur, diamond bur showed rough surfaces in all composite resin groups, so these were inappropriate for the final polishing instruments.