• 한국방재학회:학술대회논문집
• /
• 2008.02a
• /
• pp.815-818
• /
• 2008

Titanium was oxidized with oxygen plasma and calcinated with rapid thermal annealing for degradation of humic acid dissolved in water. Titania photocatalytic plate was produced by titanium surface oxidized with oxygen plasma by Plasma Enhanced Chemical Vapor Deposition(PECVD). RF-power and deposition condition is controlled under 100 W, 150 W, 300 W and 500 W. Treatment time was controlled by 5 min and 10 min. The film properties were evaluated by the X-ray Photoelectron Spectroscopy (XPS) and X-Ray Diffraction (XRD). From the experimental results, we found the optimal condition of titania film which exhibited good performance. Moreover photocatalytic capacity was about twice better than thermal spray titania film, and also as good as titania powder.

• Journal of the Korean institute of surface engineering
• /
• v.32 no.1
• /
• pp.43-48
• /
• 1999

Oxidation behavior of 304 and 316 stainless steels was studied. After solution heat treatment, specimens were polished up to 1$mu \textrm{m}$ using $Al_2O_3$ powder and then subjected to oxidation between $300^{\circ}C$ and 50$0^{\circ}C$ in dry air. TEM and EDS were used for analyzing the components and structure of oxide film. TEM analysis of oxide film revealed that thin amorphous Fe oxide ($Fe_2O_3$) was formed on the top of surface while polycrystalline (Cr, $Fe_2O_3$ was formed below the amorphous Fe oxide layer. The specimens oxidized at $500^{\circ}C$ showed that 316 stainless steel had higher oxidation resistance than 304 stainless steel. These results suggest that Mo component of 316 stainless steel suppresses the formation of Cr carbide which may result in a local Cr depleted area.

• Journal of the Korean Ceramic Society
• /
• v.29 no.7
• /
• pp.551-557
• /
• 1992

X-ray diffraction patterns, IR spectra and zeta-potentials of silicon nitride and $\beta$-Sialon powders were investigated before and after surface manipulations. $\beta$-Sialon powder was produced from Hadong Kaolin by the carbothermic reduction and simulataneous nitridation. Isoelectric points of as-prepared Si3N4 and $\beta$-Sialon powders were 8.4 and 7.4, respectively. After both silicon nitride and $\beta$-Sialon powders were oxidized at 80$0^{\circ}C$ for 24 h in air, the isoelectric points of these powders corresponded to that of silica (pH=3). I case of the addition of Darvan C as deflocculant, its isoelectric point was 3 and zeta-potential was nearly constant in the range of pH 5~12. When SN 7347 was used as deflocculant, its isoelectric point was 8.3 and zeta-potential over -156 mV was measured above pH 11.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.3
• /
• pp.31-40
• /
• 1993

The vibration-proof material normally used in structural components of precision machinery or measuring instruments requires higher damping in vibration and better characteristics in dimensional stability and rigidity to accomplish the quality assurance of the products. In this study the ferrite-resin material, which is the mixture of epoxy resin and the oxidized steel (Fe$_{3}$O$_{4}$: ferrite) in consideration of characteristics of aggregator and binder, is developed and investigated as one of vibration-proof materials. Four kinds of composite plates for experiments are made by adding another filler materials such as steel powder, granite powder and carbon-fiber sheet to the basic ferrite-resin matrix. Their characteristics are compared with a cast iron specimen which has the same bending rigidity as other specimens. The ferrite-resin material gives the best damping effect in the motor-induced vibration test. Therefore, the material can be applied to the manufacturing industry for vibration damping of machine elements.

• Journal of the Korean Ceramic Society
• /
• v.30 no.3
• /
• pp.181-188
• /
• 1993

The sintering and renitridation behaviors of ultrafine Si3N4 powder compacts, which were heavily oxidized and/or free-Si rich, were investigated with particular attentiion to microstructures. The specimens were heated without restoring to additives and pressure by controlling heating process attained a Xe image apparatus. The effect of particle size, free-Si contents, decomposition and renitridation, were investigated. When fired to 1$650^{\circ}C$ within 15 sec and then immediately held at 135$0^{\circ}C$ for 10min N2 atmosphere, significant densification took place in the limited region, in addition to decreasing oxygen contents to less than 0.3wt%. On the other hand, specimens decomposed due to overheating at the initial stage were rapidly renitridated at the relatively lower temperature of the holding stage. And, then, the activation energy for the renitridation was calculated to be 49kcal/mole.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.1
• /
• pp.42-45
• /
• 2017

The magnesium-base AZ61 alloy was cast while adding 1% CaO powder into the melt. It was hot extruded, and oxidized at $550-650^{\circ}C$ in air in order to study its microstructure and oxidation behavior. Initially added CaO powder reacted with Al in the melt to $Al_2Ca$ particles that aligned along the extrusion direction. The formed $Al_2Ca$ particles increased the oxidation resistance through forming the superficial CaO scale at the upper part of the thin MgO oxide scale.

• Journal of Powder Materials
• /
• v.11 no.2
• /
• pp.130-136
• /
• 2004

The passivation and oxidation process of tungsten and molybdenum narlopowders, produced by electrical explosion of wires was studied by means of FE-SEM, XPS. XRD, TEM, DIA-TGA and sire distribution analysis. In addition, the phase transformation of W and Mo nanopowders under oxidation in air was investigated. A chemical process is suggested for the oxidation of W and Mo nano-particles after a comprehensive testing of passivated and oxidized powders.

• Journal of the Korean Ceramic Society
• /
• v.20 no.1
• /
• pp.49-54
• /
• 1983

The main object of this study is to investigate the effect of Al powder as an additive on the sintering of calcined alumina comparing with that of calcined alumina alone. The degree of Al oxidation is calculated by measuring the weight increase during the firing Water absorption bulk density and compressive strength of the $Al_2O_3+Al$ system at each temperature are compared with those of $Al_2O_4$ alone. The $Al_2O_3+Al$ system shows better physical propeties than Al2O3 alone and it seems by the SEM observation that the fine oxidized Al particles(fine $Al_2O_3$ particles submicron unit) fill the interstices of the original $Al_2O_3$ par-ticles and thus result in the well-close-packed arrangement of the particles.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.3
• /
• pp.256-260
• /
• 2011

ZnO nanostructures with tetrapod, needle and multipod shapes were synthesized without catalysts through a simple thermal oxidation of metallic Zn powder in alumina crucible under air atmosphere. X-ray diffraction data revealed that the ZnO nanostructures had wurtzite structure of hexagonal phase. Energy dispersive X-ray (EDX) spectra showed that the ZnO was of high purity. After the oxidation of Zn powder, white colored product was mainly observed and yellow colored product was observed only a very little on the surface of the oxidized source materials. The white product consisted of tetrapods, while yellow product was composed of needles and multipods. Cathodoluminescece spectra showed that the crystalline quality of tetrapods was better that those of needles and multipods.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.19 no.3
• /
• pp.229-233
• /
• 1990

The compositions of hydroperoxy fatty acid components of lipid in raw adlay powder(RAP) and processed adlay powder(PAP) stored at 35$^{\circ}C$ and PAP lipid and triglyceride(TG) autoxi야-zed 35$^{\circ}C$ were studied. During autoxidation the time taken to reach 100 of peroxide and 13-hydroperoxide isomers were the major hydroperoxy fatty acids found in oxidized adlay lipid. Lower levels of 8-. 10-, 11-, 12- and 16-hydroperoxide isomer were also observed. The composi-tions of hydroperoxy fatty acid componets obtained from sutoxidized RAP lipid and TG were similar to those of hydroperoxy fatty acid components is lipid extracted from stored RAP and PAP.