• Journal of Electrical Engineering and Technology
• /
• 제2권3호
• /
• pp.408-412
• /
• 2007

It is almost impossible to secure the reproductibility and stability of a commercial Thick-Film Metal Oxide Semiconductor Gas Sensor since it is very difficult to keep the consistency of the manufacturing environment. Thus it is widely known that the general Semiconductor-Oxide Gas Sensors are not appropriate for precise measurement systems. In this paper, the output characteristic analyzer of the various Thick-Film Metal Oxide Semiconductor Gas Sensors that are used to recognize the air quality within an automobile are proposed and examined. The analyzed output characters in a normal air chamber are grouped by sensor ranks and used to fill out the characteristic table of the Thick-Film Metal Oxide Semiconductor Gas Sensors. The characteristic table is used to determine the rank of the sensor that is equipped in the current air cleaner system of an automobile. The proposed air control system can also adapt the on-demand operation that recognizes the history of the passenger's manual-control.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제3C권2호
• /
• pp.55-58
• /
• 2003

This paper examines the electrical characteristic of single oxide layer due to various diffusion conditions, substrate orientations, substrate resistivity and gas atmosphere in a diffusion furnace. The oxide quality was examined through the capacitance-voltage characteristic due to the annealing time after oxidation process, and the capacitance-voltage characteristics of the single oxide layer by will be described via semiconductor device simulation.

• 한국물환경학회지
• /
• 제31권2호
• /
• pp.209-215
• /
• 2015

The purpose of this study is to evaluate the characteristic of the iron oxide carrier for removing arsenic contained in the groundwater. 4 types of iron oxide carrier used in the study is iron oxide coated sand carrier (IOCSC), iron oxide coated zeolite carrier (IOCZC), iron oxide plasticity carrier (IOPC) and platinum iron oxide plasticity carrier (PIOPC). The results of this study, IOPC is showed high arsenic adsorption strength and the maximum amount of adsorption than the IOCC. Based on the results of the arsenic adsorption characteristic, by using IOCC was conducted to column test. As a result, PIOPC is showed a high arsenic adsorption amount than IOPC, it was found that the time required to reach the breakthrough point is also extended. Therefore it is determined that stably compliance with water quality standards enhanced drinking water when using the PIOPC.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2013년도 추계학술대회
• /
• pp.390-392
• /
• 2013

본 논문에서는 투명디스플레이를 구현하기 위해 가장 주목받는 ZnO 계열의 산화물반도체의 특성에 대하여 관찰하였다. 알에프 마그네트론 스퍼터링에 의해 증착된 산화물 반도체의 광학적 특성으로부터 전기적인 신호 동작특성의 상호관계를 알아보았다. 박막내의 결합 혹은 불순물이 증가할수록 PL 특성은 장파장 특성이 우세하게 나타났다. SiOC 박막위에서는 에너지 밴드갭이 증가하면서 단파장 특성이 우세하게 나타났다. 트랜지스터의 특성은 기판의 의존도가 높게 나타났다.

• 정보저장시스템학회논문집
• /
• 제8권2호
• /
• pp.56-60
• /
• 2012

Graphene oxide, which is exfoliated by oxidant from graphite, is the material for solving the problem of mass production and positioning. We made graphene oxide based devices by dielectrophoresis, studied and controlled factors which can affect the characteristic of graphene oxide channel. Graphene oxide channel assembled by dielectrophoresis can be constructed differently by various frequency options. We confirmed the change of gate characteristics and I-V characteristics in the range from 80K to 300K temperature.

• 대한치과기공학회지
• /
• 제35권4호
• /
• pp.359-364
• /
• 2013

Purpose: This study was to observe characteristic of metal oxidation and bonding strength according to composition of Ni-Cr alloy for porcelain fused to metal crown. The three kinds of Ni-Cr alloy with different composition ratio of parent metal were observed general properties and chemical properties of each alloy surface and measured the shear bonding strength between ceramic and each alloys. The aim of study was to suggest the material for design of parent metal's composition ratio to development of alloy for porcelain fused to metal crown. Methods: The three kinds of alloy as test specimen was Ni(59wt%)-Cr(24wt%), Ni(67wt.%)-Cr(16wt.%) alloy and Ni(71wt%)-Cr(12wt%)alloy. The oxide on surface was observed by EDX. And the shear test was performed by MTS. Results: The surface property and oxide characteristic analysis of oxide layer, weight percentage of Element O within $Ni_{59}Cr_{24}$ alloy measured 23.03wt%, $Ni_{67}Cr_{16}$ alloy measured 21.13wt% and $Ni_{71}Cr_{12}$ alloy was measured 48.55wt%. And the maximum shear bonding strength was measured 58.02Mpa between $Ni_{59}Cr_{24}$ alloy and vintage halo(H2 group). Conclusion: The surface property and oxide characteristic three kind of Ni-Cr alloy was similar. and shear bonding strength showed the highest bonding strength in H2 specimens.

• 대한치과기공학회지
• /
• 제35권2호
• /
• pp.105-112
• /
• 2013

Purpose: This study was to analyze the castability, surface oxide characteristic of Co-Cr alloy for porcelain fused to metal crown and the bonding strength of porcelain fused to metal crown. Co-Cr and Ni-Cr alloy for porcelain fused to metal crown was used for tests of the castability and surface oxide state and shear bonding strength by various porcelain. The aim of this study was to suggest the differences of result according to Co-Cr and Ni-Cr alloy. Methods: The kinds of alloy as test specimen was Co-Cr and Ni-Cr alloy. The castability index on the alloy specimens. The surfaces of two alloys were analyzed by SEM and EDX in order to observe oxide characteristic. And the shear test was performed by MTS. Results: The castability index of Co-Cr alloy was 96.8% and Ni-Cr alloy was 94.4%. The strongest bonding strength of Co-Cr alloy was shown 67.37 MPa. Conclusion: The shear bonding strength between Co-Cr alloy and EX3 porcelain was the strongest comparing with others. And all of each alloy was indicated as same level about the castability.

• 대한치과기공학회지
• /
• 제35권4호
• /
• pp.353-358
• /
• 2013

Purpose: This study was observation shear bonding strength by compositional change and firing step of a Ni-Cr alloy for porcelain fused metal crown. The aim of study was to suggest the material for firing step of Ni71-Cr14 alloy to development of alloy for porcelain fused to metal crown. Methods: The test was on the two kinds of Ni-Cr alloy specimens. The surfaces of two alloys were analyzed by EDX in order to observe oxide characteristic. And the shear test was performed by MTS. Results: The surface property and oxide characteristic analysis of oxide layer, weight percentage of Element O within $Ni_{71}Cr_{14}$ alloy measured 23.32wt%, and $Ni_{59}Cr_{24}$ alloy was measured 23.03wt%. And the maximum shear bonding strength was measured 58.02MPa between $Ni_{59}Cr_{24}$ alloy and vintage halo(H4 group). Conclusion: The surface property and oxide characteristic three kind of Ni-Cr alloy was similar. and shear bonding strength showed the highest bonding strength in H4 specimens.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2003년도 춘계학술발표회 초록집
• /
• pp.2-2
• /
• 2003

• 대한전자공학회논문지
• /
• 제23권1호
• /
• pp.65-73
• /
• 1986

Experiment have been conducted about thin oxide characteristics according to O2/N2 ratio needed for EEPROM cell fabrication. As a result, we think that there is no problem even if we grow oxide layer with large O2/N2 ratio and short exidation time and when the water is implated by As before oxidation, the oxide breakdown field is about IMV/cm lower than that is not implanted. Especially, the thin oxide characteristic seems to be affected largely by wafer cleaning and oxidation in air. On the basis of these, tunnel type EEPROM cell is fabricated by 3um CMOS process and its characteristic is studied. Tunnel oxide thickness(100\ulcorner is chosen to allow Fowler-Nordheim tunneling to charge the floating gate at the desired programming voltage and tunnel area(2x2um\ulcorneris chosen to increase capacitive coupling ratio. For program operation, high voltage (20-22V) is applied to the control gate, while both drain and source are gdrounded. The drain voltage for erase is 16V. It is shown that charge retention characteristics is not limited by leakage in the oxide and program/erase endurance is over 10E4 cycles of program erase operation.