• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권9호
• /
• pp.438-443
• /
• 2001

In the shallow trench isolation(STI)-chemical mechanical polishing(CMP) process, the key issues are the optimized thickness control, within-wafer-non-uniformity, and the possible defects such as pad oxide damage and nitride residue. The defect like nitride residue and silicon (or pad oxide) damage after STI-CMP process were discussed to accomplish its optimum process condition. To understand its optimum process condition, overall STI related processes including reverse moat etch, trench etch, STI fill and STI-CMP were discussed. Consequently, we could conclude that law trench depth and high CMP thickness can cause nitride residue, and high trench depth and over-polishing can cause silicon damage.

• 한국재료학회지
• /
• 제12권2호
• /
• pp.117-120
• /
• 2002

We investigated the possibility of direct bonding of the Si ∥SiO$_2$/Si$_3$N$_4$∥Si wafers for Oxide-Nitride-Oxide(ONO) gate oxide applications. 10cm-diameter 2000$\AA$-thick thermal oxide/Si(100) and 500$\AA$-Si$_3$N$_4$LPCVD/Si (100) wafers were prepared, and wet cleaned to activate the surface as hydrophilic and hydrophobic states, respectively. Cleaned wafers were premated wish facing the mirror planes by a specially designed aligner in class-100 clean room immediately. Premated wafer pairs were annealed by an electric furnace at the temperatures of 400, 600, 800, 1000, and 120$0^{\circ}C$ for 2hours, respectively. Direct bonded wafer pairs were characterized the bond area with a infrared(IR) analyzer, and measured the bonding interface energy by a razor blade crack opening method. We confirmed that the bond interface energy became 2,344mJ/$\m^2$ when annealing temperature reached 100$0^{\circ}C$, which were comparable with the interface energy of homeogenous wafer pairs of Si/Si.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.118-118
• /
• 2008

The oxide CMP has been applied to interlayer dielectric(ILD) and shallow trench isolation (STI) in chip fabrication. Recently the slurry used in oxide CMP being changed from silica slurry to ceria (cerium dioxide) slurry particularly in STI CMP, because the material selectivity of ceria slurry is better than material selectivity of silica slurry. Moreover, the ceria slurry has good a planarization efficiency, compared with silica slurry. However ceria abrasives make a material removal rate too high at the region of wafer center. Then we focuses on why profile of material removal rate is convex. The material removal rate sharply increased to 3216 $\AA$/min by $4^{th}$ run without conditioning. After $4^{th}$ run, material removal rate converged. Furthermore, profile became more convex during 12 run. And average material removal rate decreased when conditioning process is added to end of CMP process. This is due to polishing mechanism of ceria. Then the ceria abrasive remains at the pad, in particular remains more at wafer center contacted region of pad. The field emission scanning electron microscopy (FE-SEM) images showed that the pad sample in the wafer center region has a more ceria abrasive than in wafer outer region. The energy dispersive X-ray spectrometer (EDX) verified the result that ceria abrasive is deposited and more at the region of wafer center. Therefore, this result may be expected as ceria abrasives on pad surface causing the convex profile of material removal rate.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.86-87
• /
• 2007

The dispersive method of white-light interferometry is proper for in-line 3-D inspection of dielectric thin-film thickness to be used in the semiconductor and flat-panel display industry. This research is the measurement application of CMP patterned wafer. The results describe 3-D and 2-D profile of the step height during polishing time.

• 대한금속재료학회지
• /
• 제46권1호
• /
• pp.39-43
• /
• 2008

PSII (Plasma Source Ion Implantation) using high density pulsed ICP source was employed to implant oxygen ions in Si wafer. The PSII technique can achieve a nominal oxygen dose of $3 {\times}10^{17}atoms/cm^2$ in implantation time of about 20min. In order to prevent oxidation of SOI layer during high temperature annealing, the wafer was capped with $2,000{\AA}$ $Si_3N_4 $ by PECVD. Cross-sectional TEM showed that continuous $500{\AA}$ thick buried oxide layer was formed with $300{\AA}$ thick top silicon layer in the sample. This study showed the possibility of SOI fabrication using the plasma source ion implantation with pulsed ICP source.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 C
• /
• pp.1820-1822
• /
• 2004

In this study, major research fields are classified as ozone generation system for dry cleaning wafer of etched silicon wafer, dry cleaning process of etched silicon wafer which includes SEM analysis and ESCA analysis. The following results are deduced from each experiment and analysis. The magnitudes of carbon and silicon were similar to the survey spectrum of silicon wafer which does not cleaning, but magnitude of oxygen was much bigger Because UV light activates oxygen molecules in the oxide film on the silicon wafer.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.211-213
• /
• 1999

In this paper, we documented the controlling oxide removal amount on the pattern wafer using removal rate and removal thickness of blanket wafer. There was the strong correlation relationship for both(correlation factor:0.7109). So, we could confirm the repeatability as applying for STI CMP process from the obtained linear formular. As the result of repeatability test, the difference of calculated polishing time and actual polishing time was 3.48 seconds based on total 50 lots. If this time is converted into the thickness, it is from 104$\AA$ to 167$\AA$. It is possible to be ignored because it is under the process margin.

• Transactions on Electrical and Electronic Materials
• /
• 제15권4호
• /
• pp.207-212
• /
• 2014

Aluminum-doped zinc oxide (AZO) films were deposited on SiOC/Si wafer by an RF-magnetron sputtering system, by varying the deposition parameters of radio frequency power from 50 to 200 W. To assess the correlation of the optical properties between the substrate and AZO thin film, photoluminescence was measured, and the origin of deep level emission of AZO thin films grown on SiOC/Si wafer was studied. AZO formed on SiOC/Si substrates exhibited ultraviolet emission due to exciton recombination, and the visible emission was associated with intrinsic and extrinsic defects. For the AZO thin film deposited on SiOC at low RF-power, the deep level emission near the UV region is attributed to an increase of the variations of defects related to the AZO and SiOC layers. The applied RF-power influenced an energy gap of localized trap state produced from the defects, and the gap increased at low RF power due to the formation of new defects across the AZO layer caused by lattice mismatch of the AZO and SiOC films. The optical properties of AZO films on amorphous SiOC compared with those of AZO film on Si were considerably improved by reducing the roughness of the surface with low surface ionization energy, and by solving the problem of structural mismatch with the AZO film and Si wafer.

• 전자통신동향분석
• /
• 제5권1호
• /
• pp.55-70
• /
• 1990

SIMOX SOI is known to be one of the most useful technologies for fabrications of new generation ULSI devices. This paper describes the current status of SIMOX SOI technology for ULSI applications. The SIMOX wafer is vertically composed of buried oxide layer and silicon epitaxial layer on top of the silicon substrate. The buried oxide layer is used for the vertical isolation of devices The oxide layer is formed by high energy ion implantation of high dose oxygen into the silicon wafer, followed by high temperature annealing. SIMOX-based CMOS fabrication is transparent to the conventional IC processing steps without well formation. Furthermore, thin film CMOX/SIMOX can overcome the technological limitations which encountered in submicron bulk-based CMOS devices, i.e., soft-error rate, subthreshold slope, threshold voltage roll-off, and hot electron degradation can be improved. SIMOX-based bipolar devices are expected to have high density which comparable to the CMOX circuits. Radiation hardness properties of SIMOX SOI extend its application fields to space and military devices, since military ICs should be operational in radiation-hardened and harsh environments. The cost of SIMOX wafer preparation is high at present, but it is expected to reduce as volume increases. Recent studies about SIMOX SOI technology have demonstrated that the performance of the SIMOX-based submicron devices is superior to the circuits using the bulk silicon.

• 한국전기전자재료학회논문지
• /
• 제16권8호
• /
• pp.700-704
• /
• 2003

This paper describes on characteristics of 2" 3C-SiC wafer bonding using PECVD (plasma enhanced chemical vapor deposition) oxide and HF (hydrofluoride acid) for SiCOI (SiC-on-Insulator) structures and MEMS (micro-electro-mechanical system) applications. In this work, insulator layers were formed on a heteroepitaxial 3C-SiC film grown on a Si (001) wafer by thermal wet oxidation and PECVD process, successively. The pre-bonding of two polished PECVD oxide layers made the surface activation in HF and bonded under applied pressure. The bonding characteristics were evaluated by the effect of HF concentration used in the surface treatment on the roughness of the oxide and pre-bonding strength. Hydrophilic character of the oxidized 3C-SiC film surface was investigated by ATR-FTIR (attenuated total reflection Fourier transformed infrared spectroscopy). The root-mean-square suface roughness of the oxidized SiC layers was measured by AFM (atomic force microscope). The strength of the bond was measured by tensile strength meter. The bonded interface was also analyzed by IR camera and SEM (scanning electron microscope), and there are no bubbles or cavities in the bonding interface. The bonding strength initially increases with increasing HF concentration and reaches the maximum value at 2.0 ％ and then decreases. These results indicate that the 3C-SiC wafer direct bonding technique will offers significant advantages in the harsh MEMS applications.ions.